ECD SYSTEM White Smoke Emitted

DESCRIPTION


  1. Faults and Symptoms of Common Rail Diesel Components


    1. Engine Control

      Turbocharger System
      Main fault Turbocharger (compressor side seal ring, turbine side seal ring, shaft, oil drain)
      Symptoms

      White smoke

      Excessive oil consumption
      Glow System
      Main fault Open circuit, glow plug relay fault
      Symptoms Difficult to start, rough idle, knocking, white smoke (when cold)
      Data List Check the glow plug indicator light
      Diagnostic Point Measure the resistance of the glow plug
      Engine
      Main fault Loss of compression
      Symptoms Rough idle (constant lack of power)
      Data List

      Engine Speed of Cyl #1 to #4


      • When cranking during the "Check the Cylinder Compression" Active Test, if there is a high speed cylinder (approx. 100 rpm more than the other cylinders) that cylinder may lose compression.

      Injection Feedback Val #1 to #4


      • If Injection Feedback Val #1 to #4 is more than 3 mm3/st, the cylinder may have a fault.

    2. Diesel Injection

      Injector Assembly
      Main fault Blockage
      Symptoms Rough idle, lack of power, black smoke, white smoke, knocking
      Data List

      Injection Feedback Val #1 to #4


      • When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder. Injection Feedback Val #1 to #4 can be read after idling for 1 minute with the engine warmed up (engine coolant temperature is higher than 70°C (158°F)).

      Tech Tips

      When the sliding resistance of the internal parts of the injector assemblies (i.e. armature shaft, command piston and plunger) has increased due to internal contamination, injection quantity will increase at high common rail pressure due to a delay in injector assembly closure.

      Injector Driver
      Main fault Circuit fault: The injector assembly does not open.
      Symptoms Difficult to start, rough idle, lack of power, black smoke, white smoke, knocking
      Data List Same as injector assembly
      Diagnostic Trouble Code When the injector driver has a fault, some DTCs may be stored.
      Poor Quality Fuel
      Main fault -
      Symptoms Difficult to start, rough idle (especially when cold)

    3. Diesel EGR

      EGR System
      Main fault

      • Does not move smoothly

      • Does not close fully
      Symptoms

      • Rough Idle

      • EGR valve stuck closed: A loud turbocharger sound.

      • EGR valve stuck open: Difficult to start (does not stall), black smoke, white smoke (when engine is cold), lack of power, jerking (If there is an excess in the quantity of EGR and there is a heavy load, when the vehicle starts moving, a lack of power will be felt. Also, when racing the engine, there will be some black smoke).
      Data List

      Actual EGR Valve Pos., Target EGR Position


      • Generally, Actual EGR Valve Pos. = Target EGR Pos. +/-5% (fully closed: 0%, fully open: 100%).

      • Using the EGR valve Active Test, check whether Actual EGR Valve Pos. follows Target EGR Position (the engine coolant temperature and intake air temperature should be considered when a malfunction occurs).

      • EGR valve is fully closed when the ignition switch is ON (engine stopped).

      • EGR valve opens to the halfway point at idling after the engine is warmed up.

      • When the EGR valve does not close, MAF (Mass Air Flow) decreases when the vehicle is accelerated at full throttle. MAP also decreases in comparison to Target Booster Pressure, however there is not a large difference.

      EGR Close Lrn. Val., EGR Close Lrn. Status


      • When leaving the vehicle idling, when EGR Close Lrn. Status is OK, the normal range of EGR Close Lrn. Val. is 0 to 1 V.

      • In cases when EGR Close Lrn. Status. is NG or EGR Close Lrn. Val. is out of the normal range (0 to 1 V), it is possible that the EGR valve cannot completely close.

CAUTION / NOTICE / HINT

Note


  • After replacing the ECM, the new ECM requires registration (See page ) and initialization Click here.

  • After replacing a fuel supply pump assembly, the ECM requires initialization Click here.

  • After replacing an injector assembly, the ECM requires registration Click here.


  1. Explanation of Symptom

    White Smoke When the engine is misfiring, any fuel that has been injected but remains unburned is emitted as white smoke.

    Turbocharger internal oil leak Click here

    If oil leak occurs from turbine side seal, large amount of white smoke will be emitted from exhaust pipe.

    Internal oil leak is not visible from outside of turbocharger.

PROCEDURE


  1. CONFIRM CONDITIONS PRESENT WHEN WHITE SMOKE APPEARED WITH CUSTOMER


    1. Ask the customer about the conditions when the white smoke was emitted.

      - What were the driving conditions when the white smoke was generated?

      - Is the white smoke constantly emitted, or only occasionally?

      - Does the white smoke occur only when the vehicle is cold, or when the vehicle is both cold and hot?

      - Is the white smoke emitted just after starting the vehicle only, or does it continue while the vehicle is idling?

    2. Determine the symptoms of the problem to narrow down the possible causes.


    NEXT

  2. READ OUTPUT DTC (RELATING TO ENGINE)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON and turn the tester on.

    3. Enter the following menus: Powertrain / Engine and ECT / DTC.

    4. Read pending DTCs.

      Result
      Result Proceed to
      No DTCs are output A
      Engine related DTCs are output B

    B

    GO TO DTC CHART Click here

    A

  3. CHECK WHEN WHITE SMOKE IS EMITTED

    B001HBJE01
    *1 Example:

    1. Start the engine.

    2. Fully depress the accelerator pedal, and then release it.

    3. Check whether white smoke is emitted or not when racing the engine.

      Note

      Be sure not to check for white smoke indoors.

      Tech Tips


      • If the white smoke is emitted only just after engine start and disappears later, the smoke is not from the turbocharger.

      • If the turbocharger is the cause of the problem, regardless of whether the engine is cold or warmed up, there will be a large amount of white smoke to the extent that visibility is obstructed for a few meters in the area of the smoke (as shown in the illustration).

      • Depending on whether there is oil mixed with the fuel, or whether there is unburned fuel present, the smell of the exhaust gas differs. When oil is mixed in, the exhaust gas smells like burning oil.

      • When continuously traveling with the engine close to idle for 1 hour or more, such as when in heavy traffic, unburned fuel accumulates in the catalytic converter, and can produce white smoke when accelerating.

      Result
      Result Proceed to
      White smoke is emitted just after engine start only A
      White smoke is always and continuously emitted B

      There is oil on the exhaust pipe, etc.

      Tech Tips

      The oil on the exhaust pipe may be from the transmission, etc.

      		 C

    B

    CHECK IDLING CONDITION Click here

    C

    CHECK FOR OIL LEAKAGE Click here

    A

  4. CHECK TEMPERATURE WHEN WHITE SMOKE IS EMITTED


    1. Check whether the white smoke is emitted only when the engine coolant temperature is below 0°C (32°F).

      Tech Tips


      • If so, the smoke is not from the turbocharger and may be the smoke of unburned fuel.

      • If misfiring occurs, unburned fuel is emitted.

      Result
      Result Proceed to
      White smoke is emitted when the temperature is below 0°C (32°F) A
      White smoke is emitted regardless of temperature B

    B

    READ VALUE USING INTELLIGENT TESTER Click here

    A

  5. INSPECT GLOW PLUG RELAY (GLOW)


    1. Inspect the glow plug relay (glow) Click here.


    NG

    REPLACE GLOW PLUG RELAY

    OK

  6. INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)


    1. Inspect the glow plug Click here.


    NG

    REPLACE GLOW PLUG ASSEMBLY Click here

    OK

  7. READ VALUE USING INTELLIGENT TESTER


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON and turn the tester on.

    3. Start the engine

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Common Rail Pressure, Target Common Rail Pressure.

    5. B001D63E02
      *1 Snapshot Button

      Take a snapshot with the intelligent tester.

      Tech Tips

      Detailed graphs can be displayed by transferring the stored snapshot from the tester to a PC (personal computer) with Intelligent Viewer installed.

    6. Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Common Rail Pressure) when racing the engine with the accelerator pedal fully depressed.

      Result
      Result Proceed to
      Fuel pressure is within 5000 kPa of Target Common Rail Pressure A
      Except above B

      Tech Tips


      • "Target Common Rail Pressure" is the target fuel pressure controlled by the ECM.

      • "Common Rail Pressure" is the actual fuel pressure.


    B

    BLEED AIR FROM FUEL SYSTEM Click here

    A

  8. CHECK INJECTOR COMPENSATION CODE


    1. Read the injector compensation codes Click here.

      OK
      Compensation codes stored in the ECM match the compensation codes of the installed injector assemblies.

    NG

    REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING

    OK

  9. READ VALUE USING INTELLIGENT TESTER (INJECTION FEEDBACK VAL #1 TO #4, INJECTION VOLUME)


    1. Check Injection Feedback Val #1 to #4 and Injection Volume in the snapshot taken after the engine is warmed up and idled for 1 minute with the A/C off.

      Tech Tips

      Engine coolant temperature is 70°C (158°F) or higher.

      Result
      Result Proceed to

      Injection Feedback Val #1 to #4 are 3 mm3/st or less and Injection Volume is 4.5 to 10 mm3/st

      		 A
      Other than above B

    A

    CHECK ELECTRIC EGR CONTROL VALVE ASSEMBLY Click here

    B

  10. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE CYLINDER #1 TO #4 FUEL CUT)

    Tech Tips

    Use this Active Test to determine the malfunctioning cylinder.


    1. Connect the intelligent tester to the DLC3.

    2. Start the engine and turn the tester on.

    3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1 to #4 Fuel Cut.

      Tech Tips

      If the engine idle speed does not change when an injector assembly is disabled, the cylinder being tested is malfunctioning. Record any malfunctioning cylinders.


    NEXT

  11. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CHECK THE CYLINDER COMPRESSION)

    Tech Tips

    Use this Active Test to help determine whether a cylinder has compression loss or not.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON and turn the tester on.

    3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed of Cyl #1 to #4.

    4. Crank the engine.

    5. Check the engine speed during the Active Test.

      Result
      Result Proceed to
      The values of Engine Speed Cyl #1 to #4 are within 10 rpm of each other A
      Other than above B

      Tech Tips

      When cranking, if the speed of a cylinder is approximately 100 rpm more than the other cylinders, there is probably a complete loss of compression in that cylinder.


    A

    REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER Click here

    B

  12. CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER

    Tech Tips

    Measure the compression of the cylinder that had a high speed during the "Control the All Cylinders Fuel Cut" Active Test.


    1. Check cylinder compression pressure Click here.


    NG

    CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

    OK

  13. REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER

    Tech Tips

    It can be determined that the injector assembly is faulty as the corresponding cylinder is malfunctioning, but has no compression loss.


    1. Replace the injector assembly of the malfunctioning cylinder Click here.


    NEXT

  14. BLEED AIR FROM FUEL SYSTEM


    1. Bleed the air from the fuel system Click here.


    NEXT

  15. REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING


    1. Register the injector compensation codes Click here.

    2. Perform the injector pilot quantity learning Click here.


    NEXT

  16. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Check whether the white smoke problem has been successfully repaired by starting the engine.


    OK

    END

    NG

  17. CHECK FUEL QUALITY


    1. Check that only diesel fuel is being used.

    2. Check that the fuel does not contain any impurities.


    NEXT

    END

  18. BLEED AIR FROM FUEL SYSTEM


    1. Bleed the air from the fuel system Click here.


    NEXT

  19. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Check whether the white smoke problem has been successfully repaired by starting the engine.


    OK

    END

    NG

  20. CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP ASSEMBLY


    1. Disconnect the inlet hose from the fuel supply pump assembly.

    2. Operate the priming pump and check that fuel is being supplied to the fuel supply pump assembly.

      OK
      Fuel is properly supplied to the fuel supply pump assembly when the priming pump is operated.

      Tech Tips


      • A lack of fuel causes the fuel pressure to drop.

      • Check that the fuel filter element sub-assembly is not clogged.

    3. Reconnect the inlet hose.


    NEXT

  21. REPLACE FUEL FILTER ELEMENT SUB-ASSEMBLY


    1. If the fuel filter is obviously dirty or clogged, replace the fuel filter element sub-assembly.


    NEXT

  22. CHECK AND REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - FUEL SUPPLY PUMP)


    1. Check and replace the clogged fuel pipe.


    NEXT

  23. BLEED AIR FROM FUEL SYSTEM

    Tech Tips

    If the fuel filter element sub-assembly or fuel pipe has been replaced, be sure to remove any air in the system.


    1. Bleed the air from the fuel system Click here.


    NEXT

  24. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Check whether the white smoke problem has been successfully repaired by starting the engine.


    NEXT

    END

  25. CHECK ELECTRIC EGR CONTROL VALVE ASSEMBLY


    1. Inspect the electric EGR control valve assembly Click here.


    NG

    REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY Click here

    OK

  26. CHECK ENGINE ASSEMBLY


    1. Inspect the engine to see whether white smoke is being emitted due to defects in the engine itself.


      1. Check for oil leaking into the combustion chamber due to a faulty valve stem oil seal.

      2. Check for oil leaking into the combustion chamber due to a faulty injector assembly nozzle sheet.

      3. Check for low compression.

        Tech Tips

        If the engine runs too rough, Injection Feedback Val #1 to #4 cannot be corrected and the readout will (incorrectly) show that Injection Feedback Val #1 to #4 are within the normal range.

        Tech Tips

        If defects are found, perform repairs, and then check that the symptoms are no longer present.


    NEXT

    END

  27. CHECK IDLING CONDITION


    1. Start the engine.

    2. Check the idling condition.

      Result
      Result Proceed to
      There are problems such as rough idling or engine stall, and white smoke is emitted. A
      Engine runs smoothly at idle, however white smoke is emitted. B

      Tech Tips

      It is possible to determine the faulty cylinder by carrying out the "Check the Cylinder Compression" Active Test.


    B

    GO TO TURBOCHARGER OIL LEAK AND WHITE SMOKE Click here

    A

    REPAIR ENGINE ASSEMBLY

  28. CHECK FOR OIL LEAKAGE


    1. Remove any oil in the front exhaust pipe assembly.

      Tech Tips

      Oil in the exhaust pipe is producing white smoke.

    2. If there is an oil leak, repair the leak.


    NEXT

    END