LIN COMMUNICATION SYSTEM, Diagnostic DTC:B2325

DTC Code DTC Name
B2325 LIN Communication Bus Malfunction

DESCRIPTION

The main body ECU (multiplex network body ECU) monitors communication between all the ECUs connected to the door bus lines. When the main body ECU (multiplex network body ECU) detects errors in communication with all the ECUs connected to the door bus lines at 2.6-second intervals and 3 times in a row, DTC B2325 will be stored.

DTC No. DTC Detection Condition Trouble Area
B2325 Main body ECU (multiplex network body ECU) detects errors in communication with the ECUs connected to the door bus lines 3 times in a row.

  • Power window regulator motor assembly (for driver door)

  • Power window regulator motor assembly (for front passenger door)

  • Power window regulator master switch assembly

  • Sliding roof ECU (sliding roof drive gear sub-assembly)*

  • Main body ECU (multiplex network body ECU)

  • Instrument panel junction block assembly

  • Wire harness or connector

WIRING DIAGRAM

A01HZR7E06

INSPECTION PROCEDURE

Note


  • When the sliding roof ECU (sliding roof drive gear sub-assembly) is replaced or removed and reinstalled, it requires initialization Click here.

  • When a power window regulator motor assembly is replaced or removed and reinstalled, it requires initialization Click here.

  • When using the Techstream to troubleshoot with the ignition switch off:

    Connect the Techstream to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the Techstream and vehicle begins.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR) - POWER WINDOW REGULATOR MASTER SWITCH)


    1. Disconnect the K11 power window regulator master switch assembly connector.

    2. Disconnect the K9 power window regulator motor assembly (for driver door) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K11-7 (LIN2) - K9-9 (LIN) Always Below 1 Ω
      K11-7 (LIN2) or K9-9 (LIN) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


    1. A01HYHOE38
      Text in Illustration
      *a

      Component without harness connected

      (Power Window Regulator Master Switch Assembly)

      Remove the power window regulator master switch assembly Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      7 (LIN2) - 6 (LIN1) Always Below 1 Ω
      7 (LIN2) or 6 (LIN1) - Body ground Always 10 kΩ or higher

    NG

    REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY Click here

    OK

  3. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


    1. Remove the instrument panel junction block assembly Click here.

      A01HYFKE02

    2. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Tech Tips

      This inspection is to check the LIN line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).

      Standard Resistance
      Tester Connection Condition Specified Condition
      3B-30 (LIN2) - MB-16 (LIN2) Always Below 1 Ω
      Text in Illustration
      *a

      Component without harness connected

      (Instrument Panel Junction Block Assembly)

      		 *b

      Component without harness connected

      (Instrument Panel Junction Block Assembly)

    NG

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY Click here

    OK

  4. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - EACH ECU)


    1. Disconnect the J18 power window regulator motor assembly (for front passenger door) connector.

    2. Disconnect the K11 power window regulator master switch assembly connector.

    3. Disconnect the S4 sliding roof ECU (sliding roof drive gear sub-assembly)* connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3B-30 (LIN2) - K11-6 (LIN1) Always Below 1 Ω
      3B-30 (LIN2) - J18-9 (LIN) Always Below 1 Ω
      3B-30 (LIN2) - S4-11 (MPX1)* Always Below 1 Ω
      3B-30 (LIN2) - Body ground Always 10 kΩ or higher
      K11-6 (LIN1) - Body ground Always 10 kΩ or higher
      J18-9 (LIN) - Body ground Always 10 kΩ or higher
      S4-11 (MPX1)* - Body ground Always 10 kΩ or higher

      • *: w/ Sliding Roof System


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK DTC OUTPUT (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)


    1. Disconnect the K11 power window regulator master switch assembly connector.

    2. Clear the DTC Click here.

    3. After 10 seconds have elapsed, check if the trouble occurs again.

    4. Check for DTCs again.

      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output B

    B

    REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY Click here

    A

  6. CHECK DTC OUTPUT (POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR))


    1. Disconnect the K9 power window regulator motor assembly (for driver door) connector.

    2. Clear the DTC Click here.

    3. After 10 seconds have elapsed, check if the trouble occurs again.

    4. Check for DTCs again.

      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output B

    B

    REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR) Click here

    A

  7. CHECK DTC OUTPUT (POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR))


    1. Disconnect the J18 power window regulator motor assembly (for front passenger door) connector.

    2. Clear the DTC Click here.

    3. After 10 seconds have elapsed, check if the trouble occurs again.

    4. Check for DTCs again.

      Result
      Result Proceed to
      DTC B2325 is output (w/ Sliding Roof System) A
      DTC B2325 is output (w/o Sliding Roof System) B
      DTC B2325 is not output C

    B

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    C

    REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR) Click here

    A

  8. CHECK DTC OUTPUT (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY))


    1. Disconnect the S4 sliding roof ECU (sliding roof drive gear sub-assembly) connector.

    2. Clear the DTC Click here.

    3. After 10 seconds have elapsed, check if the trouble occurs again.

    4. Check for DTCs again.

      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output B

    B

    REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) Click here

    A

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here