INSTRUMENT PANEL SAFETY PAD REMOVAL

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. TABLE OF BOLT, SCREW AND NUT

    Tech Tips

    All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet code in the table below.

    B001Z8DE03

  2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (w/ Cool Box)

    Click here

  3. DISABLE AUTOAWAY/RETURN FUNCTION (for Power Tilt and Power Telescopic Steering Column)


    1. Disable the autoaway/return function by changing the customize parameter Click here.

      CAUTION:

      Record the current customize parameter setting (whether the autoaway/return function is enabled or disabled) in order to restore the current setting after finishing the operation.

      Tech Tips

      Performing the above operation causes the autoaway/return function to be disabled when the engine switch is turned off.

    2. Turn the ignition switch on (IG). Operate the tilt and telescopic switch to fully extend and lower the steering column assembly.

    3. Turn the ignition switch off.

  4. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  5. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  6. REMOVE FRONT SEAT ASSEMBLY LH


    1. for Manual Seat:

      Click here

    2. for Power Seat:

      Click here

  7. REMOVE FRONT SEAT ASSEMBLY RH


    1. for Manual Seat:

      Click here

    2. for Power Seat:

      Click here

    3. for Bench Seat Type:

      Click here

  8. REMOVE HEADLIGHT DIMMER SWITCH ASSEMBLY

    Click here

  9. REMOVE REAR CONSOLE BOX SUB-ASSEMBLY (w/o Cool Box)

    Click here

  10. REMOVE COOLING BOX ASSEMBLY (w/ Cool Box)

    Click here

  11. REMOVE LOWER CONSOLE BOX (w/o Console Box Lid)

    Click here

  12. REMOVE INSTRUMENT SIDE PANEL LH

    B001W1ME01
    Text in Illustration
    *a Protective Tape

    1. Put protective tape around the instrument side panel LH.

    2. Using a moulding remover A, detach the 6 claws and remove the instrument side panel LH.

  13. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

    B001XJYE01
    Text in Illustration
    *a Protective Tape

    1. Put protective tape around the No. 1 instrument cluster finish panel garnish.

    2. Using a moulding remover A, detach the 3 claws and remove the No. 1 instrument cluster finish panel garnish.

  14. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

    B001W7AE01
    Text in Illustration
    *a Protective Tape

    1. Put protective tape around the No. 2 instrument cluster finish panel garnish.

    2. Using a moulding remover A, detach the 2 claws and remove the No. 2 instrument cluster finish panel garnish.

  15. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

    B001Y6NE01
    Text in Illustration
    *a Protective Tape

    1. Put protective tape around the No. 2 instrument cluster finish panel sub-assembly.

    2. Detach the 9 claws.

    3. Disconnect the connectors and remove the No. 2 instrument cluster finish panel sub-assembly.

  16. REMOVE COMBINATION METER ASSEMBLY

    B001YNW

    1. Remove the 4 screws.

    2. Disconnect the connectors and remove the combination meter assembly.

  17. REMOVE FRONT DOOR SCUFF PLATE LH

    Click here

  18. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

    B001WB3E01
    Text in Illustration
    *a Screw <A>

    1. Remove the 2 screws <A>.

    2. Detach the 3 claws.

    3. Disconnect the connector and remove the No. 1 instrument panel under cover sub-assembly.

  19. REMOVE COWL SIDE TRIM BOARD LH

    B00202CE01
    Text in Illustration
    *a Cap Nut

    1. Remove the cap nut.

    2. Detach the 2 clips and remove the cowl side trim board LH.

  20. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

    B001X0HE01

    1. Using a screwdriver, detach the 2 claws and open the hole cover.

      Tech Tips

      Tape the screwdriver tip before use.

      Text in Illustration
      *a Protective Tape
    2. B001XPUE01

      Put protective tape around the lower No. 1 instrument panel finish panel.

    3. Remove the 2 bolts <B>.

      Text in Illustration
      *a Protective Tape
      *b Bolt <B>

    4. w/ Driver Side Knee Airbag:


      1. Detach the 16 claws.

        B001Y7S

    5. w/o Driver Side Knee Airbag:


      1. Detach the 9 claws.

        B001Z8Q

    6. for Automatic Air Conditioning System:


      1. B001WCJ

        Detach the 2 claws and remove the room temperature sensor.

    7. B001XC5

      Detach the 2 claws and disconnect the 2 control cables.

    8. Disconnect the connectors and remove the lower No. 1 instrument panel finish panel.

  21. REMOVE NO. 1 SWITCH HOLE BASE

    B001YJPE01
    Text in Illustration
    *a Protective Tape

    1. Put protective tape around the No. 1 switch hole base.

    2. Detach the 4 claws.

    3. Disconnect the connectors and remove the No. 1 switch hole base.

  22. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

    Click here

  23. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

    B001WYFE01
    Text in Illustration
    *a Bolt <B>

    1. Detach the 2 claws and disconnect the DLC3.

    2. Remove the 5 bolts <B> and lower instrument panel sub-assembly.

  24. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

    B001WYZE01
    Text in Illustration
    *a Protective Tape

    1. Put protective tape around the No. 1 instrument panel register assembly.

    2. Detach the 4 claws and remove the No. 1 instrument panel register assembly.

  25. REMOVE INSTRUMENT SIDE PANEL RH

    B001WKCE01
    Text in Illustration
    *a Protective Tape

    1. Put protective tape around the instrument side panel RH.

    2. Using a moulding remover A, detach the 6 claws and remove the instrument side panel RH.

    3. w/ Airbag Cut Off Switch:


      1. Disconnect the connector and remove the instrument side panel RH.

  26. REMOVE FRONT DOOR SCUFF PLATE RH

    Click here

  27. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

    B001XWE

    1. Detach the 4 claws and 3 guides.

    2. Disconnect the connector and remove the No. 2 instrument panel under cover sub-assembly.

  28. REMOVE COWL SIDE TRIM BOARD RH

    B001WPRE01
    Text in Illustration
    *a Cap Nut

    1. Remove the cap nut.

    2. Detach the 2 clips and remove the cowl side trim board LH.

  29. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Passenger Side Knee Airbag)

    Click here

  30. REMOVE LOWER INSTRUMENT PANEL (w/o Passenger Side Knee Airbag)

    B001WJ9E01
    Text in Illustration
    *a Bolt <B>

    1. Remove the 2 bolts <B>.

    2. Detach the 4 claws and remove the lower instrument panel.

  31. REMOVE NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH

    B001VRNE01
    Text in Illustration
    *a Protective Tape

    1. Put protective tape around the No. 3 instrument cluster finish panel garnish.

    2. Using a moulding remover A, detach the 6 claws and remove the No. 3 instrument cluster finish panel garnish.

  32. REMOVE INSTRUMENT PANEL BOX DOOR KNOB

    Tech Tips

    Use the same procedure for both instrument panel box door knobs.


    1. B001ZZZ

      Using a moulding remover B, detach the 2 claws and remove the instrument panel box door knob.

  33. REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

    B001X1JE01

    1. Put protective tape around the lower No. 2 instrument panel finish panel.

    2. Remove the 4 screws <C>.

      Text in Illustration
      *a Protective Tape
      *b Screw <C>
    3. B001VR0

      Detach the 3 claws.

    4. Disconnect the connector and remove the lower No. 2 instrument panel finish panel.

  34. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY

    B001Z9NE01
    Text in Illustration
    *a Protective Tape

    1. Put protective tape around the No. 2 instrument panel register assembly.

    2. Detach the 4 claws and remove the No. 2 instrument panel register assembly.

  35. REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. for Type A:


      1. B001XROE01
        Text in Illustration
        *a Protective Tape

        Put protective tape around the No. 3 instrument panel register assembly.

      2. B001ZML

        Using moulding remover B, raise the No. 3 instrument panel register assembly.

      3. B001XZX

        Pull the No. 3 instrument panel register assembly by hand to detach the 7 claws and guide and remove the No. 3 instrument panel register assembly.

    2. for Type B:


      1. B001Z0BE01
        Text in Illustration
        *a Protective Tape

        Put protective tape around the No. 3 instrument panel register assembly.

      2. B001X7X

        Using moulding remover B, raise the No. 3 instrument panel register assembly.

      3. B001ZMI

        Pull the No. 3 instrument panel register assembly by hand to detach the 6 claws and remove the No. 3 instrument panel register assembly.

  36. REMOVE NO. 4 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. for Type A:


      1. B001YOXE01
        Text in Illustration
        *a Protective Tape

        Put protective tape around the No. 3 instrument panel register assembly.

      2. B001YJG

        Using moulding remover B, raise the No. 3 instrument panel register assembly.

      3. B001YAK

        Pull the No. 3 instrument panel register assembly by hand to detach the 7 claws and guide and remove the No. 3 instrument panel register assembly.

    2. for Type B:


      1. B001YORE01
        Text in Illustration
        *a Protective Tape

        Put protective tape around the No. 3 instrument panel register assembly.

      2. B001XGX

        Using moulding remover B, raise the No. 3 instrument panel register assembly.

      3. B001ZYC

        Pull the No. 3 instrument panel register assembly by hand to detach the 6 claws and remove the No. 3 instrument panel register assembly.

  37. REMOVE MULTI-DISPLAY ASSEMBLY (w/ Navigation System)

    Click here

  38. REMOVE NO. 1 CENTER INSTRUMENT CLUSTER FINISH PANEL (w/o Navigation System)


    1. for Type A:


      1. B001YZM

        Detach the 8 claws and 3 clips.

      2. Disconnect the connectors and remove the No. 1 center instrument cluster finish panel.

    2. for Type B:


      1. B001W0V

        Detach the 10 claws.

      2. Disconnect the connectors and remove the No. 1 center instrument cluster finish panel.

  39. REMOVE RADIO TUNER OPENING COVER (w/o Radio Receiver)

    B001WMW

    1. Remove the 2 bolts.

    2. Remove the 2 screws and radio tuner opening cover.

  40. REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)

    Click here

  41. REMOVE RADIO RECEIVER ASSEMBLY (for Radio Receiver Type)

    Click here

  42. REMOVE MULTI-MEDIA MODULE RECEIVER ASSEMBLY (w/ Navigation System)

    Click here

  43. REMOVE AIR CONDITIONING CONTROL ASSEMBLY (w/o Navigation System)

    Click here

  44. REMOVE ASSIST GRIP SUB-ASSEMBLY

    Click here

  45. REMOVE FRONT PILLAR GARNISH LH

    Click here

  46. REMOVE FRONT PILLAR GARNISH RH

    Click here

  47. REMOVE NO. 1 SPEAKER OPENING COVER ASSEMBLY

    B001Y65E01
    Text in Illustration
    *a Protective Tape

    1. Put protective tape around the No. 1 speaker opening cover assembly.

    2. Using a moulding remover A, detach the 8 clips and remove the No. 1 speaker opening cover assembly.

  48. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

    B001Y2OE01
    Text in Illustration
    *a Protective Tape

    1. Put protective tape around the No. 1 instrument panel speaker panel sub-assembly.

    2. Using a moulding remover A, detach the 3 claws and 2 guides and remove the No. 1 instrument panel speaker panel sub-assembly.

  49. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

    B001ZE5E01
    Text in Illustration
    *a Protective Tape

    1. Put protective tape around the No. 2 instrument panel speaker panel sub-assembly.

    2. Using a moulding remover A, detach the 3 claws and 2 guides and remove the No. 2 instrument panel speaker panel sub-assembly.

  50. REMOVE FRONT NO. 4 SPEAKER ASSEMBLY (w/ Front Center Speaker)

    Click here

  51. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY

    Tech Tips

    Use the same procedure for the RH and LH sides Click here.

  52. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. w/o Wireless Charger:


      1. B00207G

        Detach the 6 claws.

      2. Disconnect the connectors and remove the center instrument cluster finish panel sub-assembly.

    2. w/ Wireless Charger:


      1. B001ZIZ

        Detach the 6 claws.

      2. Disconnect the connectors and remove the center instrument cluster finish panel sub-assembly.

  53. REMOVE REAR NO. 4 AIR DUCT (w/ Rear Air Duct)

    B001WYX

    1. Fold back the front floor carpet.

    2. Detach the clip and remove the rear No. 4 air duct.

  54. REMOVE REAR NO. 2 AIR DUCT (w/ Rear Air Duct)

    B001ZFM

    1. Fold back the front floor carpet.

    2. Detach the clip and remove the rear No. 2 air duct.

  55. REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY


    1. Disconnect the connector and detach the clamps.

      B001VQUE01
      Text in Illustration
      *A w/ Multi-terrian Monitor System *B w/ TOYOTA Parking Assist-sensor System

    2. Disconnect the connectors and detach the clamps.

    3. Remove the bolt and disconnect the wire harness.

      B001ZXGE01
      Text in Illustration
      *a Connector *b Bolt
    4. B001XUSE01
      Text in Illustration
      *a Lock Slider

      Pull and slide the lock slider in the direction indicated by the arrow to release the connector lock and disconnect the passenger airbag connector.

      Note

      When handling the passenger airbag connector, take care not to damage the airbag wire harness.

    5. Disconnect the connectors.

    6. Remove the 2 passenger airbag installation bolts <D>.

    7. Remove the 6 bolts <E>.

    8. Remove the 2 nuts <F>.

    9. Remove the 2 bolts <B> and instrument panel safety pad assembly.

      B001VYQE01
      Text in Illustration
      *a Passenger Airbag Connector *b Connector
      *c Passenger Airbag Installation Bolt <D> *d Bolt <E>
      *e Nut <F> *f Bolt <B>