VEHICLE STABILITY CONTROL SYSTEM TRC OFF Indicator Light Remains ON

DESCRIPTION

The TRC OFF indicator light comes on when the VSC OFF switch is operated.

WIRING DIAGRAM

B001XVUE25
*a VSC OFF Switch
*b Skid Control ECU (Master Cylinder Solenoid)
*c Combination Meter Assembly
*d CAN Communication System

CAUTION / NOTICE / HINT

Note

After replacing the master cylinder solenoid, perform zero point calibration and store the system information Click here.

PROCEDURE


  1. INSPECT IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED


    1. Check the skid control ECU (master cylinder solenoid) connector connection.

      OK
      The connector is securely connected.

    NG

    CONNECT CONNECTOR TO ECU CORRECTLY

    OK

  2. CHECK CAN COMMUNICATION LINE


    1. Turn the ignition switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the ignition switch to ON and the GTS on.

    4. Select "CAN Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN Bus.

      OK
      "CAN Bus Check" indicates no malfunctions in CAN communication.
      Result
      Result Proceed to
      OK A
      NG (for LHD) B
      NG (for RHD) C

    B

    GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) Click here

    C

    GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) Click here

    A

  3. CHECK DTC (CAN COMMUNICATION SYSTEM)


    1. Turn the ignition switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the ignition switch to ON and the GTS on.

    4. Check for DTCs (for LHD: See page , for RHD: Click here.

      Result
      Result Proceed to
      CAN system DTC is not output A
      CAN system DTC is output (for LHD) B
      CAN system DTC is output (for RHD) C

    B

    GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) Click here

    C

    GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) Click here

    A

  4. READ VALUE USING GTS (TRC/VSC OFF MODE)


    1. Turn the ignition switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the GTS on.

    5. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

      ABS/VSC/TRC
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      TRC/VSC Off Mode TRC/VSC off mode/ Normal, TRC OFF, Unknown or VSC OFF

      Normal: Normal mode

      TRC OFF: TRC OFF mode

      VSC OFF: VSC OFF mode

      		 -

    6. Check that the mode display changes according to VSC OFF switch operation.

      OK
      Display changes according to switch operation.

    OK

    GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) Click here

    NG

  5. INSPECT VSC OFF SWITCH


    1. Remove the VSC OFF switch Click here.

    2. Inspect the VSC OFF switch Click here.


    NG

    REPLACE VSC OFF SWITCH Click here

    OK

  6. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)


    1. Turn the ignition switch off.

    2. Disconnect the A24 skid control ECU (master cylinder solenoid) connector.

    3. Disconnect the G13 VSC OFF switch connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A24-9 (CSW) - G13-6 Always Below 1 Ω
      A24-9 (CSW) - Body ground Always 10 kΩ or higher
      G13-3 - Body ground Always Below 1 Ω
      Result
      Result Proceed to
      NG A
      OK (for LHD) B
      OK (for RHD) C

    A

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    B

    REPLACE MASTER CYLINDER SOLENOID Click here

    C

    REPLACE MASTER CYLINDER SOLENOID Click here