LIN COMMUNICATION SYSTEM, Diagnostic DTC:B2325

DTC Code DTC Name
B2325 LIN Communication Bus Malfunction

DESCRIPTION

The main body ECU (cowl side junction block LH) intermittently monitors the LIN communication bus between the components related to the door, double lock control relay*2 and sliding roof*1. DTC B2325 is stored when a malfunction in the LIN communication bus between the components related to the doors, double lock control relay*2 and sliding roof*1 is detected consecutively 3 times.

Tech Tips

*1: w/ Sliding Roof System

*2: w/ Double Locking System

DTC Code DTC Detection Condition Trouble Area
B2325 The main body ECU (cowl side junction block LH) detects a malfunction in the LIN communication bus between components related to the doors and sliding roof consecutively 3 times.

  • for Models with jam protection function on 4 windows


    • Master switch

    • Front power window regulator motor LH

    • Front power window regulator motor RH

    • Rear power window regulator motor LH

    • Rear power window regulator motor RH

    • Sliding roof ECU*1

    • Double lock door control relay*2

    • Main body ECU (cowl side junction block LH)

    • Harness or connector


  • for Models with jam protection function on driver door window only


    • Front power window regulator motor LH (for LHD)

    • Front power window regulator motor RH (for RHD)

    • Double lock door control relay*2

    • Main body ECU (cowl side junction block LH)

    • Harness or connector

WIRING DIAGRAM

A01X8UIE04
A01X8GEE01

CAUTION / NOTICE / HINT

Note

When using the intelligent tester with the ignition switch off to troubleshoot:

Connect the intelligent tester to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

Tech Tips

When DTC B2325 and a LIN communication stop DTC are output simultaneously, first perform the troubleshooting for the LIN communication stop DTC. Then perform the troubleshooting for DTC B2325.

PROCEDURE


  1. CLEAR DTC


    1. Clear the DTC Click here.


    NEXT

  2. CHECK FOR DTC


    1. Recheck for DTCs Click here.

      Result
      Result Proceed to
      DTC B2325 is output (for Models with Jam Protection Function on 4 Windows) A
      DTC B2325 is output (for Models with Jam Protection Function on Driver Door Window Only) B
      DTC B2325 is not output C

    B

    CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT POWER WINDOW REGULATOR MOTOR) Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

  3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - MASTER SWITCH)


    1. A01X9IOE01

      Disconnect the E3 ECU connector.

    2. Disconnect the I11*1 or I22*2 switch connector.

      Tech Tips

      *1: for LHD

      *2: for RHD

    3. Measure the resistance and voltage according to the value(s) in the tables below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E3-10 (LIN2) - I11-17 (LIN1)*1 or I22-17 (LIN1)*2 Always Below 1 Ω
      E3-10 (LIN2) - Body ground Always 10 kΩ or higher
      Standard Voltage
      Tester Connection Condition Specified Condition
      E3-10 (LIN2) - Body ground Always Below 1 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CLEAR DTC


    1. Reconnect the E3 ECU connector.

    2. Disconnect the I11*1 or I22*2 switch connector.

      Tech Tips

      *1: for LHD

      *2: for RHD

    3. Clear the DTC Click here.


    NEXT

  5. CHECK FOR DTC


    1. Recheck for DTCs Click here.

      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output B

    B

    REPLACE MASTER SWITCH

    A

  6. CLEAR DTC


    1. Reconnect the I11*1 or I22*2 switch connector.

      Tech Tips

      *1: for LHD

      *2: for RHD

    2. Disconnect the I12 motor connector.

    3. Clear the DTC Click here.


    NEXT

  7. CHECK FOR DTC


    1. Recheck for DTCs Click here.

      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output B

    B

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR LH Click here

    A

  8. CLEAR DTC


    1. Reconnect the I12 motor connector.

    2. Disconnect the I4 motor connector.

    3. Clear the DTC Click here.


    NEXT

  9. CHECK FOR DTC


    1. Recheck for DTCs Click here.

      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output B

    B

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR RH Click here

    A

  10. CLEAR DTC


    1. Reconnect the I4 motor connector.

    2. Disconnect the J4 motor connector.

    3. Clear the DTC Click here.


    NEXT

  11. CHECK FOR DTC


    1. Recheck for DTCs Click here.

      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output B

    B

    REPLACE REAR POWER WINDOW REGULATOR MOTOR LH Click here

    A

  12. CLEAR DTC


    1. Reconnect the J4 motor connector.

    2. Disconnect the J11 motor connector.

    3. Clear the DTC Click here.


    NEXT

  13. CHECK FOR DTC


    1. Recheck for DTCs Click here.

      Result
      Result Proceed to
      DTC B2325 is output (w/ Double Locking System) A
      DTC B2325 is output (w/o Double Locking System, w/ Sliding Roof System) B
      DTC B2325 is output (w/o Double Locking System, w/o Sliding Roof System) C
      DTC B2325 is not output D

    B

    CLEAR DTC Click here

    C

    REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

    D

    REPLACE REAR POWER WINDOW REGULATOR MOTOR RH Click here

    A

  14. CLEAR DTC


    1. Reconnect the J11 motor connector.

    2. Disconnect the E86 relay connector.

    3. Clear the DTC Click here.


    NEXT

  15. CHECK FOR DTC


    1. Recheck for DTC Click here.

      Result
      Result Proceed to
      DTC B2325 is output (w/ Sliding Roof System) A
      DTC B2325 is output (w/o Sliding Roof System) B
      DTC B2325 is not output (for LHD) C
      DTC B2325 is not output (for RHD) D

    B

    REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

    C

    REPLACE DOUBLE LOCK DOOR CONTROL RELAY Click here

    D

    REPLACE DOUBLE LOCK DOOR CONTROL RELAY Click here

    A

  16. CLEAR DTC


    1. Reconnect the E86 relay connector.

    2. Disconnect the R5 ECU connector.

    3. Clear the DTC Click here.


    NEXT

  17. CHECK FOR DTC


    1. Recheck for DTCs Click here.

      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output B

    A

    REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

    B

    REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY Click here

  18. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT POWER WINDOW REGULATOR MOTOR)


    1. A01X2IAE03

      Disconnect the E3 ECU connector.

    2. Disconnect the I12*1 or I4*2 motor connector.

      Tech Tips

      *1: for LHD

      *2: for RHD

    3. Measure the resistance and voltage according to the value(s) in the tables below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E3-10 (LIN2) - I12-9 (LIN)*1 or I4-9 (LIN)*2 Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  19. CLEAR DTC


    1. Reconnect the E3 ECU connector.

    2. Disconnect the I12*1 or I4*2 motor connector.

      Tech Tips

      *1: for LHD

      *2: for RHD

    3. Clear the DTC Click here.


    NEXT

  20. CHECK FOR DTC


    1. Recheck for DTCs Click here.

      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output (for LHD) B
      DTC B2325 is not output (for RHD) C

    B

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR LH Click here

    C

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR RH Click here

    A

  21. CLEAR DTC


    1. Reconnect the I12*1 or I4*2 motor connector.

      Tech Tips

      *1: for LHD

      *2: for RHD

    2. Disconnect the E86 relay connector.

    3. Clear the DTC Click here.


    NEXT

  22. CHECK FOR DTC


    1. Recheck for DTCs Click here.

      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output (for LHD) B
      DTC B2325 is not output (for RHD) C

    A

    REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

    B

    REPLACE DOUBLE LOCK DOOR CONTROL RELAY Click here

    C

    REPLACE DOUBLE LOCK DOOR CONTROL RELAY Click here