FRONT SHOCK ABSORBER REMOVAL

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. REMOVE FRONT WHEEL

  2. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

    Click here

  3. REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL (for LHD)

    Click here

  4. REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL (for RHD)

    Click here

  5. REMOVE NO. 2 HEATER AIR DUCT SPLASH SHIELD SEAL (for LHD)

    Click here

  6. REMOVE NO. 2 HEATER AIR DUCT SPLASH SHIELD SEAL (for RHD)

    Click here

  7. REMOVE COWL BODY MOUNTING REINFORCEMENT LH (for LHD)

    Click here

  8. REMOVE COWL BODY MOUNTING REINFORCEMENT RH (for RHD)

    Click here

  9. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

    Click here

  10. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

    Click here

  11. SEPARATE FRONT STABILIZER LINK ASSEMBLY


    1. A004ZTZ

      Remove the nut and separate the front stabilizer link assembly from the front shock absorber with coil spring.

      Tech Tips

      If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud bolt.

  12. SEPARATE FRONT SPEED SENSOR


    1. A004Z22

      Remove the bolt and clamp, and separate the front speed sensor and front flexible hose from the front shock absorber with coil spring.

      Note

      Be sure to separate the front speed sensor from the front shock absorber with coil spring completely.

  13. REMOVE FRONT SUSPENSION SUPPORT DUST COVER


    1. A004VK0

      Remove the front suspension support dust cover.

  14. REMOVE FRONT SHOCK ABSORBER WITH COIL SPRING


    1. A004YQG

      Loosen the front support to front shock absorber nut.

      Note


      • Do not remove the front support to front shock absorber nut.

      • Loosen the front support to front shock absorber nut only when the front shock absorber with coil spring needs to be disassembled.

    2. A005020E04
      Text in Illustration
      *1 Wooden Block
      *2 Jack

      Support the front lower No. 1 suspension sub-assembly using a jack and wooden block.

    3. B001LEU

      Remove the 2 bolts and 2 nuts, and separate the front shock absorber with coil spring (lower side) from the steering knuckle.

      Note

      When removing the nuts, keep the bolts from rotating.

    4. A004VKU

      Remove the 3 nuts and front shock absorber with coil spring.

      Note

      Make sure that the front speed sensor is completely separated from the front shock absorber with coil spring.

  15. REMOVE FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT


    1. A004XABE07

      Secure SST in a vise.

      SST
      09727-30021   ( 09727-00010, 09727-00021, 09727-00031 )
    2. A0050CQE01
      Text in Illustration
      *a Correct
      *b Incorrect

      Attach the arm of SST to the diameter of the front coil spring.

      CAUTION:


      • Make sure that the front coil spring is installed so that the distance between the upper and lower hooks of SST is at the maximum.

      • Make sure that the claws of the hooks are securely attached.

    3. Using SST, compress the front coil spring.

      CAUTION:


      • If the front coil spring bends during the compression, immediately stop the compression and reinstall SST.

      • Do not compress the spring until the coil springs contact each other.

      • Do not use an impact wrench. It will damage SST.

    4. A004ZC1

      Confirm that the front coil spring becomes free and remove the front support to front shock absorber nut.

      CAUTION:

      Do not remove the front support to front shock absorber nut when the front coil spring is not free.

  16. REMOVE FRONT SUSPENSION SUPPORT SUB-ASSEMBLY

  17. REMOVE FRONT SUSPENSION SUPPORT DUST SEAL

  18. REMOVE FRONT UPPER COIL SPRING SEAT

  19. REMOVE FRONT UPPER COIL SPRING INSULATOR

  20. REMOVE FRONT COIL SPRING

  21. REMOVE FRONT SPRING BUMPER

  22. REMOVE FRONT LOWER COIL SPRING INSULATOR

  23. REMOVE FRONT SHOCK ABSORBER ASSEMBLY