DYNAMIC RADAR CRUISE CONTROL SYSTEM, Diagnostic DTC:C1A4A

DTC Code DTC Name
C1A4A Skid Control Buzzer Circuit

DESCRIPTION

A buzzer sounds to alert the driver when the vehicle-to-vehicle distance becomes less than the set value.

DTC No. DTC Detection Condition Trouble Area
C1A4A While power switch is on (IG), skid control buzzer circuit malfunction signal is received by brake booster with master cylinder (skid control ECU) for 1 second

  • Electronically controlled brake system

  • Driving support ECU assembly

WIRING DIAGRAM

A004YL9E10

PROCEDURE


  1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SKID CONTROL BUZZER)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Chassis / ABS/VSC/TRC / Active Test / DSS Signal Buzzer.

    5. Perform the Active Test.

      OK
      Skid control buzzer sounds.

    NG

    GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM Click here

    OK

  2. CHECK WHETHER DTC OUTPUT RECURS (DTC C1A4A)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Clear the DTCs Click here.

    4. Perform the following to make sure that the DTC detection conditions are met.

      Tech Tips

      If the detection conditions are not met, the malfunction cannot be detected.


      1. Drive the vehicle at a speed of 50 km/h (30 mph) and 170 km/h (105 mph).

      2. Turn the cruise control switch (ON-OFF button) on.

      3. Push the -/SET switch to activate the cruise control.

    5. Enter the following menus: Powertrain / Radar Cruise / DTC.

    6. Read the DTCs.

      Result
      Result Proceed to
      DTC is not output A
      DTC C1A4A is output B

    A

    USE SIMULATION METHOD TO CHECK Click here

    B

  3. REPLACE DRIVING SUPPORT ECU ASSEMBLY


    1. Replace the driving support ECU assembly Click here.


    NEXT

  4. CHECK WHETHER DTC OUTPUT RECURS (DTC C1A4A)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Clear the DTCs Click here.

    4. Perform the following to make sure that the DTC detection conditions are met.

      Tech Tips

      If the detection conditions are not met, the malfunction cannot be detected.


      1. Drive the vehicle at a speed of 50 km/h (30 mph) and 170 km/h (105 mph).

      2. Turn the cruise control switch (ON-OFF button) on.

      3. Push the -/SET switch to activate the cruise control.

    5. Enter the following menus: Powertrain / Radar Cruise / DTC.

    6. Read the DTCs.

      Result
      Result Proceed to
      DTC is not output A
      DTC C1A4A is output B

    A

    END

    B

  5. REPLACE BRAKE BOOSTER WITH MASTER CYLINDER


    1. Replace the brake booster with master cylinder (skid control ECU) (See page for LHD, Click here for RHD).


    NEXT

  6. CHECK WHETHER DTC OUTPUT RECURS (DTC C1A4A)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Clear the DTCs Click here.

    4. Perform the following to make sure that the DTC detection conditions are met.

      Tech Tips

      If the detection conditions are not met, the malfunction cannot be detected.


      1. Drive the vehicle at a speed of 50 km/h (30 mph) and 170 km/h (105 mph).

      2. Turn the cruise control switch (ON-OFF button) on.

      3. Push the -/SET switch to activate the cruise control.

    5. Enter the following menus: Powertrain / Radar Cruise / DTC.

    6. Read the DTCs.

      Result
      Result Proceed to
      DTC is not output A
      DTC C1A4A is output B

    A

    END

    B

    REPLACE POWER MANAGEMENT CONTROL ECU Click here