AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) USB Audio System Recognition/Play Error

WIRING DIAGRAM

A004VLPE09
*a (Shielded)
*b No. 1 Stereo Jack Adapter Assembly
*c Radio Receiver Assembly

CAUTION / NOTICE / HINT

Tech Tips


  • When a large amount of data is in a USB device, it may take a while before play begins.

  • When using a USB device, files that are copy protected or encrypted due to copyright reasons cannot be played.

  • When files are not played in the sorted order, perform the following procedure before inspection.


    1. Add numbers in front of the file names.

    2. Put the files in a folder and copy the folder data to the USB device.

PROCEDURE


  1. CHECK USB DEVICE OR "iPod"


    1. Disconnect the USB device or "iPod" from the No. 1 stereo jack adapter assembly.

    2. Check if playable files are present on the USB device or "iPod".

      Tech Tips

      Refer to System Description for playable files Click here.

    3. Check if the USB device is a compatible format or "iPod" is a compatible version.

      Tech Tips

      Refer to System Description for compatible formats and versions Click here.

      Result
      Condition Proceed to
      No playable files exist, or incompatible device format or version A
      Playable files exist, and compatible device format or version B

    A

    USB DEVICE FORMAT WAS INCOMPATIBLE, "iPod" VERSION WAS INCOMPATIBLE, OR NO PLAYABLE FILES PRESENT

    B

  2. CHECK HARNESS AND CONNECTOR


    1. Disconnect the radio receiver assembly and No. 1 stereo jack adapter assembly connectors.

    2. A004XUBE04
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 1 Stereo Jack Adapter Assembly)
      *b

      Front view of wire harness connector

      (to Radio Receiver Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H120-1 (UPI) - H122-1 (USV1) Always Below 1 Ω
      H120-2 (UDO-) - H122-2 (US1-) Always Below 1 Ω
      H120-3 (UDO+) - H122-3 (US1+) Always Below 1 Ω
      H120-4 (UJSG) - H122-4 (UGD1) Always Below 1 Ω
      H120-5 (UJSS) - H122-5 (USG1) Always Below 1 Ω
      H120-1 (UPI) - Body ground Always 10 kΩ or higher
      H120-2 (UDO-) - Body ground Always 10 kΩ or higher
      H120-3 (UDO+) - Body ground Always 10 kΩ or higher
      H120-4 (UJSG) - Body ground Always 10 kΩ or higher
      H120-5 (UJSS) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK POWER SOURCE


    1. Reconnect the radio receiver assembly connector.

    2. A004Z20E03
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 1 Stereo Jack Adapter Assembly)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      H120-1 (UPI) - H120-4 (UJSG) Power switch on (ACC) 5 V

    NG

    REPLACE RADIO RECEIVER ASSEMBLY Click here

    OK

  4. FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK


    1. Delete all files in the USB device or "iPod" and format/restore it.

    2. Save the data again and check if it can be played on the in-vehicle device.

      Note

      Formatting a USB device or restoring an "iPod" erases all music on the device.

      Ensure that backup music data is available before performing this operation.

      OK
      Malfunction disappears.

    OK

    END

    NG

  5. REPLACE USB DEVICE OR "iPod"


    1. Turn the power switch off.

      Tech Tips

      When this malfunction occurs, it is necessary to turn off the power switch to make it possible for the vehicle to recognize a new device when it is connected.

    2. Turn the power switch on (ACC).

    3. Connect a known good USB device or "iPod" to the No. 1 stereo jack adapter assembly.

      Tech Tips


      • If the malfunction occurred when a USB device was in use, use another USB device for the inspection. If the malfunction occurred when an "iPod" was in use, use another "iPod" for the inspection.

      • Refer to System Description for compatible formats and versions Click here.


    NEXT

  6. CHECK USB DEVICE OR "iPod"


    1. Check if the USB device or "iPod" is recognized by the radio receiver assembly, or if information such as track, artist and album names are displayed on the screen.

      OK
      USB device or "iPod" is recognized or track information such as track, artist and album names are displayed.

    OK

    USB DEVICE OR "iPod" WAS INCOMPATIBLE OR DEFECTIVE

    NG

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here