REAR DOOR BELT MOULDING(for Standard Body) INSTALLATION

CAUTION / NOTICE / HINT

PROCEDURE

1. INSTALL REAR DOOR BELT MOULDING LH

   
   

   1. Attach the clip to install the new rear belt moulding.

   2. Install the 5 screws.

      Tech Tips

      Install the screws in the order shown in the illustration.

   3. Tighten the 5 belt line screws indicated by the arrows in the illustration.

      

   4. Install a nose piece to an air riveter or hand riveter. Then insert the mandrel part of a new φ4 mm waterproof rivet into the nose piece.

   5. Using the air riveter or hand riveter, install the 4 rivets shown in the illustration.

      Tech Tips

      
      

      • The rivet labeled (A) is the second rivet from the front of the rear door window frame moulding.

      • The rivet labeled (B) is the third rivet from the front of the rear door window frame moulding.

      • The rivet labeled (C) is the fourth rivet from the front of the rear door window frame moulding.

      • The rivet labeled (D) is the fifth rivet from the front of the rear door window frame moulding.

      • If the rivet cannot be cut, pull it once and cut it.

      

      *1	Rivet A
      *2	Rivet B
      *3	Rivet C
      *4	Rivet D

      Note

      
      

      • 

        *1	INCORRECT
        *2	Riveter
        *3	Mandrel
        *4	CORRECT

        Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

      • 

        *1	Riveter
        *2	INCORRECT
        *3	CORRECT

        Confirm that the rivets are seated properly against the moulding.

      • Do not tilt the riveter when installing the rivet to the moulding.

      • Do not leave any space between the rivet head and moulding.

      • 

        *1	Riveter
        *2	INCORRECT
        *3	CORRECT

        Do not leave any space between the moulding and door frame. Firmly hold together the 2 items while installing the rivet.

2. INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH

   Click here

3. INSTALL REAR DOOR QUARTER WINDOW GLASS LH

   Click here

4. INSTALL REAR DOOR GLASS RUN LH

   Click here

5. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

   Click here

6. INSTALL REAR DOOR DIVISION BAR LOWER BRACKET LH

   Click here

7. INSTALL REAR DOOR SERVICE HOLE COVER LH

   Click here

8. INSTALL REAR DOOR GLASS INNER WEATHERSTRIP LH

   Click here

9. INSTALL REAR SIDE TRIM BOARD COVER LH (w/ Rear Door Sunshade)

   Click here

10. INSTALL REAR CURTAIN SUB-ASSEMBLY LH (w/ Rear Door Sunshade)

    Click here

11. INSTALL REAR DOOR NO. 2 WEATHERSTRIP LH

    Click here

12. INSTALL REAR DOOR NO. 2 FRAME GARNISH LH

    Click here

13. INSTALL REAR DOOR NO. 3 WEATHERSTRIP LH

    Click here

14. INSTALL REAR DOOR FRAME GARNISH LH

    Click here

15. INSTALL REAR DOOR TRIM COVER LH

    Click here

16. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

    
    

    1. w/o Rear Door Sunshade:

       Install the rear door trim board Click here.

    2. w/ Rear Door Sunshade:

       Install the rear door trim board Click here.

17. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

    Click here

18. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH

    Click here

19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some system need to be initialized after the cable is reconnected Click here.

20. INSTALL COWL TOP VENTILATOR LOUVER RH

    Click here