PROCEDURES NECESSARY WHEN CABLE IS DISCONNECTED/RECONNECTED TO BATTERY TERMINAL
Necessary Procedures | Effects / Inoperative Functions When Necessary Procedures are not Performed | See page |
---|---|---|
Steering angle sensor zero point calibration | Adaptive high beam system | |
Correction of steering angle neutral point | Parking assist monitor system | |
Reset rear door sunshade system | Rear door curtain function | |
Reset power trunk lid system | Power trunk lid function |
Note
After the engine switch is turned off, the multi-media module receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.
Condition | Waiting Time |
---|---|
Vehicle enrolled in telematics system (w/ telematics transceiver for G-BOOK) | 6 minutes |
Vehicle not enrolled in telematics system (w/ telematics transceiver for G-BOOK) | 1 minute |
CAUTION:
Make sure that the bracket of the earth wire is fixed to the vehicle body with the ground bolt.
PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED
Replacement Part | Necessary Procedures | Effects / Inoperative Functions When Necessary Procedures are not Performed | See Page |
---|---|---|---|
for 1UR-FE |
Register VIN | DTC P0630 is output | |
Register cruise control system | Cruise control system | ||
for 1UR-FSE |
Register VIN | DTC P0630 is output | |
Register cruise control system | Cruise control system | ||
for AA80F |
|
|
|
for AA80E |
|
|
|
for AA80F |
Learning by driving (Road test) |
|
|
AA80E |
Learning by driving (Road test) |
|
|
for AA80F |
|
|
|
for AA80E |
|
|
|
for AA80F |
|
|
|
for AA80E |
|
|
|
|
|
|
|
|
|
|
Click here (for Registration) Click here (for Initialization) |
|
|
|
Click here (for Initialization) Click here (for Calibration) |
|
|
Brake does not operate properly | |
|
|
|
|
|
|
|
|
|
|
Electric parking brake does not operate normally | |
|
|
|
|
|
Parking brake bedding | Parking brake performance may not be normal | |
|
Actuator angle neutral point calibration and initialization | Steering wheel off-center | |
|
|
|
|
|
|
|
|
w/ Blocking System |
Registration | Engine Starting | Refer to the Service Bulletin for the registration procedure. |
|
Inspect rear millimeter wave radar sensor (Rear radar sensor check) |
Rear millimeter wave radar sensor sensitivity may decrease | |
|
Adjust rear millimeter wave radar sensor | DTC C1A13 or C1A15 is output | |
|
Adjust object recognition camera | DTC C1A22 or C1A23 is output | |
|
Adjust object recognition camera (night view camera) | DTC B281A, B2827, C1A22 AND C1A3 are output | |
|
Initialize driving support ECU | Object recognition camera does not operate normally | |
|
Adjust front millimeter wave radar sensor | DTC C1A11 or C1A14 is output | |
Multi-media module receiver assembly |
for G-BOOK: |
G-BOOK service | |
for G-BOOK: |
Some G-BOOK service content will be unavailable | ||
Parking assist monitor system initialize | Parking assist function | ||
Telematics Transceiver |
for G-BOOK: |
G-BOOK service | |
except G-BOOK: |
Emergency call service | ||
Telematics mobilephone battery | Reset mobilephone battery condition | Emergency call service | |
|
Parking assist monitor system initialize |
|
|
|
Television camera optical axis (Camera position setting) | Vehicle width extension lines and expected course are deviated | |
|
|||
|
Adjust adaptive high beam camera beam axis | DTC B2454 is output | |
|
|
|
|
|
Initialize power window control system |
|
|
|
Position sensor initialization |
|
|
|
Position sensor initialization |
|
|
|
Reset power trunk lid system | Power trunk lid function | |
|
Rear curtain position reset operation | Rear curtain function | |
|
Initialize sliding roof system |
|
|
|
Registration |
|
Refer to service Bulletin for registration procedure |