REAR DOOR REMOVAL

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. REMOVE COWL TOP VENTILATOR LOUVER RH

    Click here

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG LH


    1. A001AUT

      Using a screwdriver, detach the 3 claws and remove the rear door inside handle bezel plug LH.

      Tech Tips

      Tape the screwdriver tip before use.

  5. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

    A001ESQE01

    1. Apply protective tape to the area around the rear rear power window regulator switch assembly with rear door armrest base panel.

    2. Using a clip remover, detach the 2 clips in the order shown in the illustration.

      Text in Illustration
      *1 Protective Tape
    3. A001EBX

      Disconnect the connector.

    4. Remove the screw and illumination light.

    5. Remove the rear rear power window regulator switch assembly with rear door armrest base panel.

  6. REMOVE ROOM TEMPERATURE SENSOR (w/ Rear Cooler)

    Click here

  7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH (w/o Rear Door Sunshade)


    1. A001E6P

      for Long Body:


      1. Remove the 3 screws.

      2. Detach the 13 clips.

        Note

        Do not use a tool to detach the clips of the rear door trim board sub-assembly LH.

      3. A00198O

        Disconnect the 2 cables from the inside handle.

      4. Disconnect the connectors and remove the trim board.

    2. A001DIX

      for Standard Body:


      1. Remove the 3 screws.

      2. Detach the 11 clips.

        Note

        Do not use a tool to detach the clips of the rear door trim board sub-assembly LH.

      3. A00198O

        Disconnect the 2 cables from the inside handle.

      4. Disconnect the connectors and remove the trim board.

  8. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH (w/ Rear Door Sunshade)


    1. A001F9U

      for Long Body:


      1. Remove the 3 screws.

      2. Detach the 14 clips.

        Note

        Do not use a tool to detach the clips of the rear door trim board sub-assembly LH.

      3. A00198O

        Disconnect the 2 cables from the inside handle.

      4. Disconnect the connectors and remove the rear door trim board sub-assembly LH.

    2. A001FYK

      for Standard Body:


      1. Remove the 3 screws.

      2. Detach the 12 clips.

        Note

        Do not use a tool to detach the clips of the rear door trim board sub-assembly LH.

      3. A00198O

        Disconnect the 2 cables from the inside handle.

      4. Disconnect the connectors and remove the rear door trim board sub-assembly LH.

  9. REMOVE REAR DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY LH


    1. A001A0X

      Detach the claw, disconnect the connector and then remove the light.

  10. REMOVE COURTESY LIGHT ASSEMBLY


    1. A001F95

      Detach the claw.

    2. Disconnect the connector and remove the courtesy light assembly.

  11. REMOVE REAR SEAT MEMORY SWITCH (w/ Rear Seat Memory System)

    Click here

  12. REMOVE REAR NO. 3 SPEAKER ASSEMBLY (for 19 Speakers)

    Click here

  13. REMOVE REAR DOOR TRIM COVER LH


    1. A001AYN

      Remove the cushion.

    2. Using a clip remover, detach the 5 clips and remove the rear door trim cover LH.

  14. REMOVE REAR DOOR FRAME GARNISH LH


    1. A001CI2

      w/o Rear Door Sunshade:


      1. Remove the screw and detach the clip.

      2. Detach the claws and remove the rear door frame garnish LH.

    2. A001AAE

      w/ Rear Door Sunshade:


      1. Detach the 2 clips.

      2. Detach the claws and remove the rear door frame garnish LH.

  15. REMOVE REAR DOOR NO. 3 WEATHERSTRIP LH


    1. A001BFFE01
      Text in Illustration
      *1 Double-sided Tape

      Detach the 2 claws and remove the rear door No. 3 weatherstrip LH.

  16. REMOVE REAR DOOR NO. 2 FRAME GARNISH LH


    1. A001AFHE08
      Text in Illustration
      *A w/o Rear Door Sunshade
      *B w/ Rear Door Sunshade

      Detach the claws and remove the rear door No. 2 frame garnish LH.

  17. REMOVE REAR DOOR NO. 2 WEATHERSTRIP LH


    1. A001EQ6

      Detach the clip and remove the rear door No. 2 weatherstrip LH.

  18. REMOVE REAR ACCESS PANEL WEATHERSTRIP LH


    1. A001FVRE01
      Text in Illustration
      *1 Double-sided Tape

      Remove the rear access panel weatherstrip LH.

  19. REMOVE REAR CURTAIN SUB-ASSEMBLY LH (w/ Rear Door Sunshade)

    Click here

  20. REMOVE NO. 1 AUTO CURTAIN RAIL BRACKET LH (w/ Rear Door Sunshade)


    1. A001A0H

      Using a clip remover, detach the clip and remove the No. 1 auto curtain rail bracket LH.

  21. REMOVE REAR SIDE TRIM BOARD COVER LH (w/ Rear Door Sunshade)


    1. A001C0E

      Remove the 2 screws and rear side trim board cover LH.

  22. REMOVE REAR DOOR GLASS INNER WEATHERSTRIP LH


    1. for Long Body:


      1. A001FC2

        Remove the rear door glass inner weatherstrip LH by pulling it upward in the direction indicated by the arrow.

    2. for Standard Body:


      1. A001CXE

        Remove the rear door glass inner weatherstrip LH by pulling it upward in the direction indicated by the arrow.

  23. REMOVE REAR NO. 1 SPEAKER ASSEMBLY

    Click here

  24. REMOVE REAR DOOR SPEAKER COVER


    1. A001FM5

      Remove the 3 screws.

    2. Disconnect the claw and remove the rear door speaker cover.

  25. REMOVE REAR NO. 2 SPEAKER ASSEMBLY (for 19 Speakers)

    Click here

  26. REMOVE REAR DOOR ECU LH


    1. A001B0S

      Remove the 2 screws and rear door ECU LH.

    2. Disconnect the 3 connectors.

  27. REMOVE REAR DOOR SERVICE HOLE COVER LH


    1. A001BWW

      Remove the rear door service hole cover LH.

  28. REMOVE REAR DOOR DIVISION BAR LOWER BRACKET LH


    1. A001A5M

      Remove the 3 nuts and rear door division bar lower bracket LH.

  29. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH


    1. A001CHW

      Remove the 2 nuts.

    2. Remove the rear door window division bar sub-assembly LH together with the rear door glass run LH.

  30. REMOVE REAR DOOR GLASS RUN LH


    1. Remove the rear door glass run LH from the division bar assembly.

  31. REMOVE REAR DOOR QUARTER WINDOW GLASS LH


    1. A001DIZ

      Remove the rear door quarter window glass LH and rear door quarter window weatherstrip LH as a unit as shown in the illustration.

  32. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH


    1. Remove the hole plug.

    2. A001CYH

      Remove the 2 bolts.

      Note

      Be careful when removing the bolts as the glass may fall and become damaged.

    3. Remove the rear door glass sub-assembly LH.

      Tech Tips

      Remove the glass upward.

      Note

      Be careful not to damage the glass.

  33. REMOVE REAR DOOR UPPER WINDOW FRAME MOULDING LH


    1. for Standard Body:

      Click here

    2. for Long Body:

      Click here

  34. REMOVE REAR DOOR BELT MOULDING LH


    1. A001BEZ

      Remove the 2 screws.

    2. A0019L0

      Loosen the 5 belt line screws indicated by the arrows in the illustration.

    3. Remove the 3 screws.

    4. A001FF8E05

      Put protective tape around the rear door belt moulding LH.

    5. While making sure not to pull the rear door belt moulding LH away from the vehicle, rotate the rear door belt moulding LH in the direction shown in the illustration and remove it.

      Note

      Be careful not to damage the door panel when rotating the belt moulding.

      Tech Tips

      The clip will break when the rear belt moulding is removed.

    6. Remove the remaining part of the clip from the body.

      Text in Illustration
      *1 Protective Tape

  35. REMOVE REAR DOOR FRONT WINDOW GUIDE SUB-ASSEMBLY LH


    1. A001EJ3

      Remove the 2 bolts and rear door front window guide sub-assembly LH.

  36. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH


    1. Disconnect the connector.

    2. A001F9NE04
      Text in Illustration
      *1 Temporary Bolt

      Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the window regulator may fall and become damaged.

    3. Remove the 3 bolts and rear door window regulator sub-assembly LH.

      Note

      Be careful when removing the screws as the motor may fall and become damaged.

    4. Remove the temporary bolt from the rear door window regulator sub-assembly LH.

  37. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


    1. A001BMD

      Using a T25 ''TORX'' driver, remove the 3 screws and power window regulator motor assembly LH.

      Note

      Be careful when removing the screws as the motor may fall and become damaged.

  38. REMOVE REAR DOOR LOCK ASSEMBLY LH

    Click here

  39. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    1. A001E5JE04
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the claw.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A001CWM

      Remove the rear door lock remote control cable assembly LH.

  40. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    1. A00198YE06

      Using a screwdriver, detach the 3 claws.

      Tech Tips

      Tape the screwdriver tip before use.

      Text in Illustration
      *1 Protective Tape
    2. A001CKY

      Remove the rear door inside locking cable assembly LH.

  41. REMOVE REAR DOOR OUTSIDE HANDLE COVER LH


    1. A001DHR

      Using a T30 ''TORX'' socket, loosen the screw and remove the rear door outside handle cover LH.

  42. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH


    1. A001EW6

      Using a T30 "TORX" wrench, loosen the screw.

    2. A001E5A

      Disconnect the connector.

    3. Remove the rear door outside handle assembly LH by sliding and pulling it in the direction indicated by the arrow in the illustration.

  43. REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH


    1. A001FW7

      Using a T30 ''TORX'' socket, remove the screw and rear door outside handle frame sub-assembly LH.

      Tech Tips

      Remove the outside handle frame through the service hole.

    2. A001G00

      Disconnect the connector and detach the 3 clamps.

  44. REMOVE DOOR ELECTRICAL KEY OSCILLATOR (for Rear Door)


    1. A001DHO

      Remove the screw and door electrical key oscillator.

  45. REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD


    1. A001ELI

      Detach the 3 claws and remove the rear door front outside handle pad.

  46. REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD


    1. A001EAW

      Detach the 2 claws and remove the rear door rear outside handle pad.

  47. REMOVE REAR DOOR CHECK COVER LH


    1. A001C63

      Remove the rear door check cover LH.

  48. REMOVE REAR DOOR CHECK ASSEMBLY LH


    1. A001D97

      Remove the bolt, 2 nuts and rear door check assembly LH.

      Tech Tips

      Remove the door check through the service hole.

      Note

      Be careful when removing the bolts as the door check may fall and become damaged.

  49. REMOVE REAR DOOR WEATHERSTRIP LH


    1. for Long Body:


      1. A001DV6

        Detach the 19 clips and remove the rear door weatherstrip LH.

    2. for Standard Body:


      1. A001FZ0

        Detach the 18 clips and remove the rear door weatherstrip LH.