FRONT POWER SEAT MOTOR ASSEMBLY INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.

PROCEDURE


  1. INSTALL FRONT SEAT WIRE LH


    1. Attach the 13 wire harness clamps to install the front seat wire LH.

    2. Connect the 4 connectors.

    3. Install the bolt.

      Torque:
      16 N*m  { 163 kgf*cm, 12 ft.*lbf }
      A0019TW

  2. INSTALL SEAT POSITION AIRBAG SENSOR

    Click here

  3. INSTALL SEAT CLIMATE CONTROL BLOWER LH

    Click here

  4. INSTALL FRONT SEAT CLIMATE CONTROL ECU LH

    Click here

  5. INSTALL FRONT NO. 2 SEAT TRAVEL LINK

    Click here

  6. INSTALL FRONT NO. 1 SEAT TRAVEL LINK

    Click here

  7. INSTALL NO. 1 SEAT CUSHION PLATE

    Click here

  8. INSTALL FRONT SEAT CUSHION SPRING

    Click here

  9. INSTALL FRONT SEAT LOWER CUSHION SHIELD

    Click here

  10. INSTALL RECLINING ADJUSTER INSIDE COVER LH

    Click here

  11. INSTALL RECLINING ADJUSTER INSIDE COVER RH

    Click here

  12. INSTALL FRONT SEATBACK FRAME ASSEMBLY LH

    Click here

  13. INSTALL FRONT SEAT HEADREST ADJUSTER SUB-ASSEMBLY


    1. w/ Active Headrest:


      1. A001EBS

        Attach the 2 claws.

      2. Install the headrest adjuster with the 2 bolts.

        Torque:
        5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
      3. A001FVE

        Connect the connector and attach the 2 wire harness clamps.

    2. w/ Pre-crash Intelligent Headrest:


      1. A001EJH

        Attach the 2 claws to connect the connector to the connector holder.

      2. A001BK5

        Attach the guide to install the plate.

      3. Install the screw.

      4. A001AHR

        Attach the 2 claws.

      5. Install the headrest adjuster with the 2 bolts.

        Torque:
        5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      6. Attach the 4 wire harness clamps.

      7. A001FVE

        Connect the connector and attach the 2 wire harness clamps.

    3. w/ Retractable Headrest:


      1. A001944

        Install the headrest stay cover with the 2 screws.

      2. A001EX6

        Attach the 2 claws to install the cable.

      3. A001DSW

        Attach the 2 claws to install the motor.

      4. A001B37

        Attach the 2 claws to install the headrest adjuster.

      5. Install the 4 bolts and 2 screws.

        Torque:
        21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  14. INSTALL ACTIVE HEADREST INFLATOR (w/ Active Headrest)

    Click here

  15. INSTALL FRONT SEATBACK COVER WITH PAD

    Click here

  16. INSTALL POWER SEAT SWITCH ASSEMBLY (w/ Shoulder Switch)

    Click here

  17. INSTALL FRONT SEAT HEADREST SUPPORT

    Click here

  18. INSTALL FRONT SEAT HEADREST ASSEMBLY

    Click here

  19. INSTALL FRONT SEAT CUSHION ASSEMBLY LH

    Click here

  20. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH

    Click here

  21. INSTALL FRONT SEAT INNER CUSHION SHIELD LH

    Click here

  22. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

    Click here

  23. INSTALL FRONT SEAT INNER NO. 1 CUSHION SHIELD LH (for Driver Side)

    Click here

  24. INSTALL FRONT SEAT INNER NO. 1 CUSHION SHIELD RH (for Front Passenger Side)

    Click here

  25. INSTALL FRONT SEAT CUSHION SHIELD LH

    Click here

  26. INSTALL FRONT SEAT ASSEMBLY LH

    Click here

  27. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  28. INSTALL COWL TOP VENTILATOR LOUVER RH

    Click here

  29. CHECK SRS WARNING LIGHT

    Click here

  30. CHECK FRONT SEAT ASSEMBLY


    1. Check the power seat operation:

      Click here

    2. Check the climate control seat system:

      Click here