LIGHTING SYSTEM, Diagnostic DTC:B241E, B241F

DTC Code DTC Name
B241E Headlamp Shade Motor LH Circuit
B241F Headlamp Shade Motor RH Circuit

DESCRIPTION

The headlight shade ECU operates the shade motor inside the headlight based on information from the AFS ECU.

DTC Code DTC Detection Condition Trouble Area
B241E Malfunction in headlight shade motor LH

  • Headlight assembly LH

  • Headlight LED unit assembly LH (for LO/ HI beam)*

  • Headlight shade ECU

  • AFS ECU
B241F Malfunction in headlight shade motor RH

  • Headlight assembly RH

  • Headlight LED unit assembly RH (for LO/ HI beam)*

  • Headlight shade ECU

  • AFS ECU

WIRING DIAGRAM

A001AVBE06
A001AZ5E01

PROCEDURE


  1. CLEAR DTC


    1. Clear the DTC Click here.


    NEXT

  2. PERFORM ACTIVE TEST USING GTS (VARIABLE SHADE BEAM)


    1. Using the GTS, perform the Active Test Click here.

      AHS
      Tester Display Test Part Control Range
      Variable Shade Beam LH Variable shade beam LH operation OFF - ON
      Variable Shade Beam RH Variable shade beam RH operation OFF - ON

    NEXT

  3. CHECK FOR DTC


    1. Check for DTC Click here.

      OK
      DTC B241E or B241F output does not occur

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

  4. CHECK HEADLIGHT TYPE


    1. Check headlight type.

      Result
      Result Proceed to
      for HID Headlight A
      for LED Headlight B

    B

    INSPECT HEADLIGHT ASSEMBLY Click here

    A

  5. CHECK HEADLIGHT SHADE ECU


    1. Temporarily replace the headlight shade ECU with a new or normally functioning one Click here.


    NEXT

  6. PERFORM ACTIVE TEST USING GTS (VARIABLE SHADE BEAM)


    1. Using the GTS, perform the Active Test Click here.

      AHS
      Tester Display Test Part Control Range
      Variable Shade Beam LH Variable shade beam LH operation OFF - ON
      Variable Shade Beam RH Variable shade beam RH operation OFF - ON

    NEXT

  7. CHECK FOR DTC


    1. Check for DTC Click here.

      OK
      DTC B241E or B241F output does not occur

    OK

    END (HEADLIGHT SHADE ECU WAS DEFECTIVE)

    NG

  8. CHECK HEADLIGHT ASSEMBLY


    1. Temporarily replace the headlight with a new or normally functioning one Click here.


    NEXT

  9. PERFORM ACTIVE TEST USING GTS (VARIABLE SHADE BEAM)


    1. Using the GTS, perform the Active Test Click here.

      AHS
      Tester Display Test Part Control Range
      Variable Shade Beam LH Variable shade beam LH operation OFF - ON
      Variable Shade Beam RH Variable shade beam RH operation OFF - ON

    NEXT

  10. CHECK FOR DTC


    1. Check for DTC Click here.

      OK
      DTC B241E or B241F output does not occur

    OK

    END (HEADLIGHT WAS DEFECTIVE)

    NG

    REPLACE AFS ECU Click here

  11. INSPECT HEADLIGHT ASSEMBLY


    1. A001FG4E03
      *1 Front view of wire harness connector: (to Headlight LED Unit [for LO/HI Beam])
      *2 Front view of wire harness connector: (to Headlight Shade ECU)

      Remove the headlight Click here.

    2. Disconnect the headlight LED unit (for LO/HI beam) connector Click here.

    3. Disconnect the headlight shade ECU connector Click here.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (ACG1) - 2 Always Below 1 Ω
      2 (ACT1) - 1 Always Below 1 Ω
      9 (ACT2) - 3 Always Below 1 Ω
      10 (ACG2) - 4 Always Below 1 Ω

    NG

    REPLACE HEADLIGHT ASSEMBLY Click here

    OK

  12. CHECK HEADLIGHT LED UNIT ASSEMBLY (FOR LO/HI BEAM)


    1. Temporarily replace the headlight LED unit (for LO/HI beam) with a new or normally functioning one Click here.


    NEXT

  13. PERFORM ACTIVE TEST USING GTS (VARIABLE SHADE BEAM)


    1. Using the GTS, perform the Active Test Click here.

      AHS
      Tester Display Test Part Control Range
      Variable Shade Beam LH Variable shade beam LH operation OFF - ON
      Variable Shade Beam RH Variable shade beam RH operation OFF - ON

    NEXT

  14. CHECK FOR DTC


    1. Check for DTC Click here.

      OK
      DTC B241E or B241F output does not occur

    OK

    END (HEADLIGHT LED UNIT [FOR LO/HI BEAM] WAS DEFECTIVE)

    NG

  15. CHECK HEADLIGHT SHADE ECU


    1. Temporarily replace the headlight shade ECU with a new or normally functioning one Click here.


    NEXT

  16. PERFORM ACTIVE TEST USING GTS (VARIABLE SHADE BEAM)


    1. Using the GTS, perform the Active Test Click here.

      AHS
      Tester Display Test Part Control Range
      Variable Shade Beam LH Variable shade beam LH operation OFF - ON
      Variable Shade Beam RH Variable shade beam RH operation OFF - ON

    NEXT

  17. CHECK FOR DTC


    1. Check for DTC Click here.

      OK
      DTC B241E or B241F output does not occur

    OK

    END (HEADLIGHT SHADE ECU WAS DEFECTIVE)

    NG

    REPLACE AFS ECU Click here