REAR SEAT OUTER BELT ASSEMBLY INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedures for LHD and RHD vehicles.

  • The procedures listed below are for LHD vehicles.

PROCEDURE


  1. INSTALL REAR SEAT OUTER BELT ASSEMBLY CENTER

    A001ES6E01
    *1 Claw

    1. Align the seat belt positioning hole with the claw.

    2. Temporarily install the rear seat outer belt assembly center with the 2 bolts.

    3. Tighten the rear side bolt first, then the front side bolt to install the rear seat outer belt assembly center.

      Torque:
      for rear bolt
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
      for front bolt
      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }

  2. INSTALL REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH

    A001EJ7E01
    *1 Claw

    1. Insert the claw of the retractor (a) into the hole.

    2. Align the seat belt positioning hole with the claw and install the retractor of the rear seat 3 point type belt assembly LH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    3. A001DFT

      Connect the pretensioner connector and lock the locking button as shown in the illustration.

    4. w/ Tension Reducer System:

      Connect the tension reducer connector.

  3. INSTALL REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH

    A001ESVE03
    *1 Claw

    1. Insert the claw of the retractor (a) into the hole.

    2. Align the seat belt positioning hole with the claw and install the retractor of the rear seat 3 point type belt assembly RH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    3. A001C2K

      Attach the wire harness clamp.

    4. Connect the pretensioner connector and lock the locking button as shown in the illustration.

    5. w/ Tension Reducer System:

      Connect the tension reducer connector.

  4. INSTALL NO. 4 AIR DUCT REAR (w/ Rear Cooler)

    Click here

  5. INSTALL NO. 5 AIR DUCT REAR (w/ Rear Cooler)

    Click here

  6. INSTALL ROOF SIDE NO. 2 AIR DUCT LH (w/ Rear Cooler)

    Click here

  7. INSTALL ROOF SIDE NO. 2 AIR DUCT RH (w/ Rear Cooler)

    Click here

  8. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY

    Click here

  9. INSTALL INNER ROOF SIDE GARNISH LH

    Click here

  10. INSTALL INNER ROOF SIDE GARNISH RH

    Click here

  11. INSTALL REAR SEAT SIDE GARNISH LH

    Click here

  12. INSTALL REAR SEAT SIDE GARNISH RH

    Click here

  13. INSTALL REAR DOOR SCUFF PLATE LH


    1. for Standard Body:

      Click here

    2. for Long Body:

      Click here

  14. INSTALL REAR DOOR SCUFF PLATE RH


    1. for Standard Body:

      Click here

    2. for Long Body:

      Click here

  15. INSTALL REAR SEAT CENTER ARMREST ASSEMBLY


    1. for Power Seat:

      Click here

    2. for 5-Passenger with Ottoman:

      Click here

  16. INSTALL REAR SEATBACK ASSEMBLY (for Fixed Seat Type)

    Click here

  17. INSTALL REAR SEATBACK ASSEMBLY LH


    1. for Power Seat:

      Click here

    2. for Ottoman:

      Click here

  18. INSTALL REAR SEATBACK ASSEMBLY RH


    1. for Power Seat:

      Click here

    2. for Ottoman:

      Click here

  19. INSTALL REAR SEAT CONSOLE BOX ASSEMBLY (for 4-Passenger with Ottoman)

    Click here

  20. INSTALL REAR SEAT LOWER CONSOLE BOX COVER (for 4-Passenger with Ottoman)

    Click here

  21. CONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH

    A001B8EE01
    *1 Protruding Part

    1. Connect the anchor part of the rear seat 3 point type belt assembly LH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear seat 3 point type belt assembly LH to overlap the protruding parts of the floor panel.

    2. Check if the ELR locks.

      Note

      The check should be performed with the rear seat 3 point type belt assembly LH installed.


      1. With the rear seat 3 point type belt assembly LH installed, check that the belt locks when it is pulled out quickly.

  22. CONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  23. CONNECT REAR SEAT OUTER BELT ASSEMBLY CENTER

    A001FZQE01
    *1 Protruding Part

    1. for Power Seat, 5-Passenger with Ottoman:

      Connect the anchor part of the rear seat outer belt assembly center with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear seat outer belt assembly center to overlap the protruding parts of the floor panel.

    2. A0019K6E02
      *1 Protruding Part

      for Fixed Seat Type:

      Connect the anchor part of the rear seat outer belt assembly center with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear seat outer belt assembly center to overlap the protruding parts of the floor panel.

    3. Check if the ELR locks.

      Note

      The check should be performed with the outer belt assembly installed.


      1. With the rear seat outer belt assembly center installed, check that the belt locks when it is pulled out quickly.

  24. INSTALL REAR CENTER SEAT CUSHION ASSEMBLY


    1. for Power Seat:

      Click here

    2. for 5-Passenger with Ottoman:

      Click here

  25. INSTALL REAR SEAT CUSHION ASSEMBLY (for Fixed Seat Type)

    Click here

  26. INSTALL REAR SEAT CUSHION ASSEMBLY LH


    1. for Power Seat:

      Click here

    2. for Ottoman Seat:

      Click here

  27. INSTALL REAR SEAT CUSHION ASSEMBLY RH


    1. for Power Seat:

      Click here

    2. for Ottoman Seat:

      Click here

  28. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  29. INSTALL COWL TOP VENTILATOR LOUVER RH

    Click here

  30. CHECK SRS WARNING LIGHT

    Click here