FRONT UPPER SUSPENSION ARM(for 2WD) INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedures for the RH side and LH side.

  • The procedures listed below are for the LH side.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.

PROCEDURE


  1. TEMPORARILY TIGHTEN FRONT NO. 1 SUSPENSION UPPER ARM ASSEMBLY LH


    1. A001F66

      Insert the bolt as shown in the illustration. Then temporarily install the front No. 1 suspension upper arm assembly LH to the No. 1 arm attachment plate inner LH with the nut.

  2. TEMPORARILY TIGHTEN FRONT NO. 2 SUSPENSION UPPER ARM ASSEMBLY LH


    1. A001DEJ

      Insert the bolt as shown in the illustration. Then temporarily install the front No. 2 suspension upper arm assembly LH to the No. 2 arm attachment plate inner LH with the nut.

  3. INSTALL NO. 1 ARM ATTACHMENT PLATE INNER LH


    1. A001FL1E01
      *1 Spacer

      Install the No. 1 arm attachment plate inner LH with the 3 bolts and spacers.

      Torque:
      32 N*m  { 326 kgf*cm, 24 ft.*lbf }

  4. INSTALL NO. 2 ARM ATTACHMENT PLATE INNER LH


    1. A001EDZE02
      *1 Spacer

      Install the No. 2 arm attachment plate inner LH with the 2 bolts and spacer.

      Torque:
      32 N*m  { 326 kgf*cm, 24 ft.*lbf }

  5. INSTALL STEERING KNUCKLE SUB-ASSEMBLY LH

    Click here

  6. INSTALL FRONT PNEUMATIC CYLINDER LH O-RING (w/ Air Suspension)

    Click here

  7. INSTALL FRONT SHOCK ABSORBER ASSEMBLY LH (w/o Air Suspension)

    Click here

  8. INSTALL PNEUMATIC CYLINDER WITH FRONT SHOCK ABSORBER ASSEMBLY LH (w/ Air Suspension)

    Click here

  9. INSTALL ABSORBER CONTROL ACTUATOR (w/ Air Suspension)

    Click here

  10. INSTALL FRONT SHOCK ABSORBER CAP LH (w/ Air Suspension)

    Click here

  11. INSTALL ENGINE ROOM SIDE COVER LH

    Click here

  12. INSTALL AIR CLEANER INLET COVER SUB-ASSEMBLY

    Click here

  13. TEMPORARILY TIGHTEN FRONT NO. 2 SUSPENSION LOWER ARM ASSEMBLY LH

    Click here

  14. CONNECT NO. 8 HEIGHT CONTROL TUBE (w/ Air Suspension)

    Click here

  15. INSTALL AIR CONNECTOR CLIP HOLDER (w/ Air Suspension)

    Click here

  16. INSTALL FRONT STABILIZER LINK ASSEMBLY LH

    Click here

  17. CONNECT FRONT HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH

    Click here

  18. CONNECT FRONT NO. 1 SUSPENSION LOWER ARM ASSEMBLY LH

    Click here

  19. CONNECT TIE ROD ASSEMBLY LH

    Click here

  20. INSTALL FRONT DISC BRAKE DUST COVER LH

    Click here

  21. INSTALL FRONT DISC

    Click here

  22. CONNECT FRONT DISC BRAKE CALIPER ASSEMBLY LH

    Click here

  23. CONNECT SPEED SENSOR CONNECTOR

    Click here

  24. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

  25. INSTALL COWL TOP VENTILATOR LOUVER


    1. Install the cowl top ventilator louver for 1UR-FSE Click here.

    2. Install the cowl top ventilator louver for 1UR-FE Click here.

  26. PERFORM INITIALIZATION


    1. Perform the initialization Click here.

  27. STABILIZE SUSPENSION (w/o Air Suspension)

    Click here

  28. STABILIZE SUSPENSION (w/ Air Suspension)

    Click here

  29. TIGHTEN FRONT NO. 1 SUSPENSION UPPER ARM ASSEMBLY LH


    1. A001EEA

      Tighten the installation nut of the front No. 1 suspension upper arm assembly LH.

      Torque:
      50 N*m  { 510 kgf*cm, 37 ft.*lbf }

  30. TIGHTEN FRONT NO. 2 SUSPENSION UPPER ARM ASSEMBLY LH


    1. A001E7V

      Tighten the installation nut of the front No. 2 suspension upper arm assembly LH.

      Torque:
      50 N*m  { 510 kgf*cm, 37 ft.*lbf }

  31. TIGHTEN FRONT NO. 2 SUSPENSION LOWER ARM ASSEMBLY LH

    Click here

  32. INSTALL FRONT WHEEL

    Torque:
    140 N*m  { 1428 kgf*cm, 103 ft.*lbf }

  33. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT


    1. Inspect and adjust the front wheel alignment Click here.

  34. ADJUST VEHICLE HEIGHT

    Click here

  35. INSPECT FOR AIR LEAK (w/ Air Suspension)

    Click here

  36. ADJUST HEADLIGHT ASSEMBLY

    Click here

  37. ADJUST OBJECT RECOGNITION CAMERA

    Click here