CAMSHAFT TIMING CONTROL MOTOR INSTALLATION

PROCEDURE


  1. INSTALL CAMSHAFT TIMING CONTROL WITH EDU MOTOR ASSEMBLY LH


    1. A0019U2E02

      Turn the camshaft timing gear's eccentric shaft keyway part counterclockwise by hand and set it to the maximum retard angle.

      Tech Tips


      • When the cam of the camshaft lifts the valve, the eccentric shaft becomes difficult to turn.

      • The position where the eccentric shaft stops is the maximum retard angle.

      Note

      When turning the eccentric shaft keyway part, do not use any tools as the keyway part may be damaged.

    2. Turn the eccentric shaft clockwise until the groove labeled A and mark labeled B are aligned as shown in the illustration.

      Tech Tips

      Make sure that the groove labeled A is positioned as close as possible to the center of the mark labeled B.

    3. Install a new O-ring to the timing chain cover.

    4. A001AWP

      Align the joint of the camshaft timing control with EDU motor assembly LH and the keyway of the camshaft timing gear assembly, and install the camshaft timing control with EDU motor assembly LH with the 3 bolts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

      Note


      • Do not allow foreign matter to contact the oil seal face of the camshaft timing control with EDU motor assembly LH (connecting surface with timing chain cover).

      • When installing the camshaft timing control with EDU motor assembly LH, do not use excessive force.

      • Do not drop the camshaft timing control with EDU motor assembly LH. If dropped, replace it.

      • Do not disassemble the camshaft timing control with EDU motor assembly LH. If disassembled, replace it.

      Tech Tips


      • Check that [L] is printed on the label of the camshaft timing control with EDU motor assembly LH.

      • When installing the camshaft timing control with EDU motor assembly LH, be sure to align the timing chain cover knock pin with the camshaft timing control with EDU motor assembly LH pin hole.

      • Install the camshaft timing control with EDU motor assembly LH with the arrow facing upward.

    5. A0019TT

      Connect the 2 camshaft timing control with EDU motor assembly LH connectors and engine wire clamp.

  2. INSTALL CAMSHAFT TIMING CONTROL WITH EDU MOTOR ASSEMBLY RH


    1. A001D2PE01

      Turn the camshaft timing gear's eccentric shaft keyway part counterclockwise by hand and set it to the maximum retard angle.

      Tech Tips


      • When the cam of the camshaft lifts the valve, the eccentric shaft becomes difficult to turn.

      • The position where the eccentric shaft stops is the maximum retard angle.

      Note

      When turning the eccentric shaft keyway part, do not use any tools as the keyway part may be damaged.

    2. Turn the eccentric shaft clockwise until the groove labeled A and mark labeled B are aligned as shown in the illustration.

      Tech Tips

      Make sure that the groove labeled A is positioned as close as possible to the center of the mark labeled B.

    3. Install a new O-ring to the timing chain cover.

    4. A001EVA

      Align the joint of the camshaft timing control with EDU motor assembly RH and the keyway of the camshaft timing gear assembly, and install the camshaft timing control with EDU motor assembly RH with the 3 bolts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

      Note


      • Do not allow foreign matter to contact the oil seal face of the camshaft timing control with EDU motor assembly RH (connecting surface with timing chain cover).

      • When installing the camshaft timing control with EDU motor assembly RH, do not use excessive force.

      • Do not drop the camshaft timing control with EDU motor assembly RH. If dropped, replace it.

      • Do not disassemble the camshaft timing control with EDU motor assembly RH. If disassembled, replace it.

      Tech Tips


      • Check that [R] is printed on the label of the camshaft timing control with EDU motor assembly RH.

      • When installing the camshaft timing control with EDU motor assembly RH, be sure to align the timing chain cover knock pin with the camshaft timing control with EDU motor assembly RH pin hole.

      • Install the camshaft timing control with EDU motor assembly RH with the arrow facing upward.

    5. A001CJ4

      Install the engine wire bracket with the bolt.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

    6. Connect the 2 camshaft timing control with EDU motor assembly RH connectors.

  3. INSTALL INTAKE AIR CONNECTOR PIPE

    Click here

  4. REMOVE COWL TOP VENTILATOR LOUVER

    Click here

  5. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  6. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    Tech Tips

    Disconnect the cable from the negative (-) battery terminal so that the maximum retard angle of the camshaft timing control with EDU motor assembly will be learned.

  7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  8. INSTALL COWL TOP VENTILATOR LOUVER

    Click here