SPEED SENSOR INSTALLATION

PROCEDURE


  1. INSTALL SPEED SENSOR SP2

    A001EOD

    1. Install the speed sensor to the transmission case with the bolt.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

    2. Connect the sensor connector.

  2. INSTALL SPEED SENSOR NC3

    A0019SG

    1. Install the speed sensor to the transmission case with the bolt.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

    2. Connect the sensor connector.

  3. INSTALL SPEED SENSOR NT

    A001A13

    1. Coat a new O-ring of the speed sensor with ATF.

    2. Using a T30 ''TORX'' wench, install the speed sensor with the bolt.

      Torque:
      6.8 N*m  { 69 kgf*cm, 60 in.*lbf }

    3. Connect the sensor connector.

  4. INSTALL TRANSMISSION VALVE BODY ASSEMBLY

    A001B0D

    1. Install the spring and check ball body.

    2. A001EJK

      Align the groove of the manual valve with the lever pin.

    3. A001AVIE02

      Install the 17 bolts.

      Torque:
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }

      Tech Tips

      Each bolt length is indicated below.

      Bolt length
      21 mm (0.83 in.) for bolt A
      31 mm (1.22 in.) for bolt B
      64 mm (2.52 in.) for bolt C
    4. A001EH1

      Install the detent spring and detent spring cover with the bolt.

      Note

      Make sure to install the detent spring so that its roller is perpendicularly at the center of the manual valve lever.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }
    5. A001F6S

      Connect the 8 connectors to the solenoid valves.

    6. Connect the oil pressure switch connector.

    7. Coat a new O-ring with ATF and install it to the ATF temperature sensor.

    8. Install the ATF temperature sensor and lock plate with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  5. INSTALL VALVE BODY OIL STRAINER ASSEMBLY

    A001BFBE02
    *1 New O-Ring

    1. Coat a new O-ring with ATF and install it to the oil strainer.

      Note

      Ensure that the O-ring is not twisted or pinched.

    2. A001CBE

      Install the oil strainer to the valve body with the 4 bolts.

      Torque:
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }

  6. INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY


    1. A0019ESE02
      *1 Magnet

      Install the 3 magnets to the oil pan.

    2. A001DU7

      Install a new gasket and the oil pan to the transmission case with the 9 bolts.

      Torque:
      7.4 N*m  { 75 kgf*cm, 65 in.*lbf }

      Note


      • A0019UDE01
        *1 CORRECT
        *2 INCORRECT
        *3 Protrusion
        *4 Sleeve

      • Make sure that there is no oil or foreign matter on the gasket seal surface and oil pan contact surface.

      • Install the gasket so that there is no slack in the gasket, and that the seal surface's entire circumference is level.

      • Make sure that the 9 gasket drop prevention protrusions are set on the oil pan.

      • When tightening the oil pan, make sure that the gasket is not pinched between the gasket tightening area's sleeve and the transmission's seal surface.

  7. INSTALL NO. 1 EXHAUST PIPE SUPPORT BRACKET SUB-ASSEMBLY

    Click here

  8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

  9. INSTALL COWL TOP VENTILATOR LOUVER

    Click here

  10. ADD AUTOMATIC TRANSMISSION FLUID


    1. Add automatic transmission fluid Click here.

  11. PERFORM INITIALIZATION


    1. Perform initialization Click here.

      Note

      Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.