ROOF HEADLINING(for Wagon) REMOVAL

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY

    Click here

  4. REMOVE REAR SIDE SEATBACK ASSEMBLY LH

    Click here

  5. REMOVE REAR SIDE SEATBACK ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  6. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

    A004TFC

    1. Pull the lever and remove the tonneau cover.

  7. REMOVE ROOM PARTITION NET ASSEMBLY (w/ Partition Net)

    A004U4Z

    1. Push the 2 buttons and remove the room partition net.

  8. REMOVE LOWER DECK TRIM SIDE BOARD LH (w/ Partition Board)


    1. Remove the lower deck trim side board.

  9. REMOVE LOWER DECK TRIM SIDE BOARD RH (w/ Partition Board)


    1. Remove the lower deck trim side board.

  10. REMOVE DECK BOARD ASSEMBLY

    A004U1M

    1. Detach the clip and 2 guides, and remove the deck board.

  11. REMOVE DECK BOARD SUB-ASSEMBLY

    A004QDV

    1. Pull the lever and remove the deck board.

  12. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY


    1. Detach the clip and remove the No. 3 deck board.

      A004TWVE01
      *1 w/o Deck Rail:
      *2 w/ Deck Rail:
      Text in Illustration
      *A w/o Deck Rail *B w/ Deck Rail

  13. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY

    Tech Tips

    Use the same procedure described for the No. 3 deck board.

  14. REMOVE REAR DECK FLOOR BOX


    1. Detach the 7 guides and remove the rear deck floor box.

      A004TODE01
      *1 w/ Spare Tire:
      *2 w/o Spare Tire:
      Text in Illustration
      *A w/ Spare Tire *B w/o Spare Tire

  15. REMOVE FLOOR SIDE RAIL LH (w/ Deck Rail)

    A004QS7

    1. Remove the 3 bolts and floor side rail.

  16. REMOVE FLOOR SIDE RAIL RH (w/ Deck Rail)

    Tech Tips

    Use the same procedure described for the LH side.

  17. REMOVE NO. 2 DECK SIDE TRIM COVER (w/o Deck Rail)

    A004PMU

    1. Detach the 2 clips and 3 guides, and remove the deck side trim cover.

  18. REMOVE NO. 1 DECK SIDE TRIM COVER (w/o Deck Rail)

    Tech Tips

    Use the same procedure described for the No. 2 deck side trim cover.

  19. REMOVE NO. 6 DECK SIDE TRIM COVER (w/o Deck Rail)

    A004Q1X

    1. Detach the 3 claws and remove the No. 6 deck side trim cover.

  20. REMOVE NO. 5 DECK SIDE TRIM COVER (w/o Deck Rail)

    Tech Tips

    Use the same procedure described for the No. 6 deck side trim cover.

  21. REMOVE ROPE HOOK ASSEMBLY (w/o Deck Rail)

    A004PBP

    Tech Tips

    Use the same procedure for all the rope hooks.


    1. Remove the bolt and rope hook.

  22. REMOVE DECK FLOOR BOX LH

    A004QXJ

    1. Remove the bolt.

    2. Detach the 5 guides and remove the deck floor box.

  23. REMOVE DECK FLOOR BOX RH

    Tech Tips

    Use the same procedure described for the LH side.

  24. REMOVE REAR FLOOR FINISH PLATE

    A004NWX

    1. Detach the 4 clips and remove the rear floor finish plate.

  25. REMOVE FRONT DECK FLOOR BOX

    A004OEG

    1. Remove the 2 clips.

    2. Detach the 4 guides and remove the front deck floor box.

  26. REMOVE FRONT DOOR SCUFF PLATE LH

    Click here

  27. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  28. REMOVE COWL SIDE TRIM BOARD LH

    Click here

  29. REMOVE COWL SIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure described for the LH side.

  30. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    Click here

  31. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  32. REMOVE REAR DOOR SCUFF PLATE LH

    Click here

  33. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  34. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

    A004TFM

    1. Remove the rear door opening trim weatherstrip.

  35. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  36. REMOVE BACK DOOR WEATHERSTRIP

    A004OMA

    1. Remove the back door weatherstrip.

  37. REMOVE FRONT PILLAR GARNISH LH

    A004NROE02
    Text in Illustration
    *1 Front Pillar Garnish Clip

    1. Pull the upper part of the garnish toward the inside of the cabin and detach the 2 clips.

      Tech Tips

      Make the front pillar garnish hang down from the front pillar garnish clip.

    2. A004SK1E02
      Text in Illustration
      *1 Front Pillar Garnish Clip

      Cut the front pillar garnish clip.

    3. Detach the 2 guides and remove the front pillar garnish.

    4. Using a clip remover, remove the remaining front pillar garnish clip on the body side.

    5. A004R97E01
      Text in Illustration
      *1 Curtain Shield Airbag Assembly
      *2 Adhesive Tape
      *3 Protective Cover

      Protect the curtain shield airbag assembly.


      1. Completely cover the airbag with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.

        Note

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

  38. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  39. REMOVE LOWER CENTER PILLAR GARNISH LH

    Click here

  40. REMOVE LOWER CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  41. REMOVE LAP BELT OUTER ANCHOR COVER

    Click here

  42. REMOVE CENTER PILLAR GARNISH LH

    Click here

  43. REMOVE CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  44. REMOVE INNER ROOF SIDE GARNISH CAP LH

    A004PHDE01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the inner roof side garnish cap.

    2. Using a screwdriver, detach the 2 claws and remove the inner roof side garnish cap.

      Tech Tips

      Tape the screwdriver tip before use.

  45. REMOVE INNER ROOF SIDE GARNISH CAP RH

    Tech Tips

    Use the same procedure described for the LH side.

  46. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH


    1. Remove the bolt and clip.

    2. Detach the 7 clips and 3 claws.

    3. Pass the fuel lid opener cable through the panel, disconnect the connector, and then remove the deck trim side panel.

      A004RPEE02
      Text in Illustration
      *1 Fuel Lid Opener Cable - -

  47. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH


    1. Remove the bolt and clip.

    2. Detach the 7 clips and 3 claws, and remove the deck trim side panel.

      A004T57

  48. REMOVE INNER ROOF SIDE GARNISH LH

    A004SFBE02
    Text in Illustration
    *1 Clip A

    1. Detach the 6 clips (do not detach clip A).

    2. Pull the inner roof side garnish in the direction indicated by the arrow in the illustration and remove it.

      Tech Tips

      Clip A remains attached to the body.

    3. Remove clip A from the vehicle body.

  49. REMOVE INNER ROOF SIDE GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  50. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY

    Tech Tips


    • Use the same procedure for RHD and LHD vehicles.

    • The procedure listed below is for LHD vehicles.


    1. Remove the upper instrument panel sub-assembly Click here.

  51. REMOVE COIN BOX ASSEMBLY

    Click here

  52. REMOVE MAP LIGHT ASSEMBLY

    Click here

  53. REMOVE NO. 1 ROOM LIGHT ASSEMBLY

    Click here

  54. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

    Click here

  55. REMOVE RAIN SENSOR COVER (w/ Rain Sensor)

    Click here

  56. REMOVE NO. 2 PRE-CRASH SAFETY CITY COVER (w/ Pre-crash Safety System)

    Click here

  57. REMOVE PRE-CRASH SAFETY CITY COVER (w/ Pre-crash Safety System)

    Click here

  58. REMOVE VISOR ASSEMBLY LH

    Click here

  59. REMOVE VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  60. REMOVE VISOR HOLDER

    Click here

  61. REMOVE ASSIST GRIP SUB-ASSEMBLY

    Click here

  62. REMOVE REAR ASSIST GRIP ASSEMBLY LH

    Click here

  63. REMOVE REAR ASSIST GRIP ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  64. REMOVE REAR ROOM PARTITION NET HOOK LH

    A004NCY

    1. Remove the screw.

    2. Detach the 2 claws and remove the rear room partition net hook.

  65. REMOVE REAR ROOM PARTITION NET HOOK RH

    Tech Tips

    Use the same procedure described for the LH side.

  66. REMOVE ROOF HEADLINING ASSEMBLY

    A004PSM

    Tech Tips

    Before removing the roof headlining, move the front seats and rear seat to the positions shown in the illustration.


    1. A004PRD

      w/ EC Mirror:

      Disconnect the EC mirror connector.

    2. A004SXD

      w/ Rain Sensor:

      Disconnect the rain sensor connector.

    3. A004QO9

      w/ Pre-crash Safety System:

      Disconnect the pre-crash safety city sensor connector.

    4. A004QQ4

      Disconnect the connector and 3 clamps from the front pillar RH.

    5. A004S8K

      Remove the 2 bolts.

    6. Disconnect the 3 connectors and 3 clamps from the rear pillar RH.

    7. A004O9U

      w/ Roof Sunshade System:

      Disconnect the connector from the rear pillar LH.

    8. A004OK2

      Disconnect the 4 clamps from the front pillar LH.

    9. for LHD:


      1. A004SE7E02
        Text in Illustration
        *A for LHD

        Disconnect the 2 clamps.

      2. A004Q9OE02
        Text in Illustration
        *A for LHD

        Disconnect the 2 roof wire connectors.

    10. for RHD:


      1. A004NNSE02
        Text in Illustration
        *A for RHD

        Disconnect the 2 clamps and roof wire connector.

      2. A004P0ME02
        Text in Illustration
        *A for RHD

        Disconnect the roof wire connector.

    11. w/o Roof Sunshade System:


      1. Remove the 5 clips.

        A004UCF

    12. w/ Roof Sunshade System:


      1. Remove the 5 clips.

      2. Detach the 3 guides and 12 fasteners.

        A004SMXE02
        Text in Illustration
        *1 Guide *2 Fastener
    13. A004U76

      Remove the roof headlining from the back door as shown in the illustration.

      Note

      Be careful not to damage the roof headlining when taking it out.

  67. REMOVE FRONT DOOR SCUFF PLATE OUTSIDE LH

    Click here

  68. REMOVE FRONT DOOR SCUFF PLATE OUTSIDE RH

    Tech Tips

    Use the same procedure described for the LH side.

  69. REMOVE REAR DOOR SCUFF PLATE OUTSIDE LH

    Click here

  70. REMOVE REAR DOOR SCUFF PLATE OUTSIDE RH

    Tech Tips

    Use the same procedure described for the LH side.

  71. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

    Click here

  72. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  73. REMOVE REAR NO. 2 SIDE RAIL SPACER LH

    Click here

  74. REMOVE REAR NO. 2 SIDE RAIL SPACER RH

    Tech Tips

    Use the same procedure described for the LH side.

  75. REMOVE REAR NO. 3 SIDE RAIL SPACER LH

    A004SIV

    1. Detach the 2 claws and remove the No. 3 side rail spacer.

  76. REMOVE REAR NO. 3 SIDE RAIL SPACER RH

    Tech Tips

    Use the same procedure described for the LH side.

  77. REMOVE FRONT DECK RAIL BRACKET LH (w/ Deck Rail)

    A004MOS

    1. Remove the 2 bolts and front deck rail bracket.

  78. REMOVE FRONT DECK RAIL BRACKET RH (w/ Deck Rail)

    Tech Tips

    Use the same procedure described for the LH side.

  79. REMOVE NO. 4 LUGGAGE COMPARTMENT TRIM BRACKET (w/o Deck Rail)

    A004PWS

    1. Remove the bolt and No. 4 luggage compartment trim bracket.

  80. REMOVE NO. 3 LUGGAGE COMPARTMENT TRIM BRACKET (w/o Deck Rail)

    Tech Tips

    Use the same procedure described for the No. 4 luggage compartment trim bracket.

  81. REMOVE NO. 2 DECK BOARD BRACKET

    A004RYW

    1. Remove the 2 bolts and No. 2 deck board bracket.

  82. REMOVE NO. 1 DECK BOARD BRACKET

    Tech Tips

    Use the same procedure described for the No. 2 deck board bracket.

  83. REMOVE TONNEAU COVER HOLDER BRACKET LH (w/ Partition Net)

    A004O2R

    1. Remove the 2 bolts and tonneau cover holder bracket.

  84. REMOVE TONNEAU COVER HOLDER BRACKET RH (w/ Partition Net)

    Tech Tips

    Use the same procedure described for the LH side.