UPPER INSTRUMENT PANEL REMOVAL

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. TABLE OF BOLT, SCREW AND NUT

    Tech Tips

    All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet code in the table below.

    A0058H6E01

  2. DISABLE AUTOAWAY/RETURN FUNCTION (for Power Tilt and Power Telescopic Steering Column)


    1. Disable the Autoaway/Return function by changing the customize parameter Click here.

      Note

      Record the current customize parameter setting (whether the Autoaway/Return function is enabled or disabled) in order to restore the current setting after finishing the operation.

      Tech Tips

      Performing the above operation causes the Autoaway/Return function to be disabled when the ignition switch is turned off.

    2. Turn the ignition switch to ON. Operate the tilt and telescopic switch to fully extend and lower the steering column.

    3. Turn the ignition switch off.

  3. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable some systems need to be initialized after the cable is reconnected Click here.

  5. REMOVE COMBINATION METER ASSEMBLY


    1. Remove the combination meter assembly Click here.

  6. REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL


    1. A0057J2E01
      Text in Illustration
      *1 Protective Tape
      *2 Clamp
      *3 Guide

      Place protective tape as shown in the illustration.

    2. Using a moulding remover B, detach the 2 clips and 5 claws.

    3. Detach the clamp.

    4. Detach the guide near the front of the vehicle and remove the finish panel.

  7. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


    1. A0057ARE01
      Text in Illustration
      *1 Protective Tape
      *2 Clamp
      *3 Guide

      Place protective tape as shown in the illustration.

    2. Using a moulding remover B, detach the 2 clips and 5 claws.

    3. Detach the clamp.

    4. Detach the guide near the front of the vehicle and remove the finish panel.

  8. REMOVE NO. 3 BOX PANEL

    Click here

  9. REMOVE INSTRUMENT PANEL FINISH PANEL END LH


    1. Using a moulding remover B, detach the 4 clips and 5 claws and remove the panel end.

      A0053ZRE01
      *1 for LHD without Entry and Start System:
      *2 for LHD with Entry and Start System:

  10. REMOVE INSTRUMENT PANEL FINISH PANEL END RH (for LHD)


    1. A0058RS

      Using a moulding remover B, detach the 4 clips and 5 claws and remove the panel end.

  11. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


    1. A00571R

      Slightly bend the upper part of the glove compartment door to release the 2 stoppers and open the glove compartment door until it is horizontal.

    2. A005739

      Pull the glove compartment door toward the rear of the vehicle to detach the 2 hinges and remove the glove compartment door.

  12. REMOVE INSTRUMENT PANEL FINISH PANEL END RH (for RHD)


    1. w/o TOYOTA Parking Assist-sensor System:


      1. Using a moulding remover B, detach the 4 clips and 5 claws and remove the panel end.

    2. w/ TOYOTA Parking Assist-sensor System:


      1. Using a moulding remover B, detach the 4 clips and 5 claws.

      2. Remove the panel end and then disconnect the connector.

        A0057QBE01
        *1 w/o TOYOTA Parking Assist-sensor System:
        *2 w/ TOYOTA Parking Assist-sensor System:

  13. REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY WITH FINISH PANEL (w/o Audio)


    1. A0058Q5E01
      Text in Illustration
      *1 Protective Tape

      Place protective tape as shown in the illustration.

    2. Using a moulding remover B, detach the 2 clips and hook.

    3. A0056CM

      Detach the 3 claws and 3 hooks.

    4. Detach the 6 clips.

    5. A0054DU

      Remove the panel register. Then disconnect the connector and detach the clamp.

  14. REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY WITH FINISH PANEL (w/ Audio)


    1. A00554CE01
      Text in Illustration
      *1 Protective Tape

      Place protective tape as shown in the illustration.

    2. Using a moulding remover B, detach the 2 clips and hook.

    3. A00550Z

      Detach the 3 claws and 3 hooks.

    4. Detach the 2 clips.

    5. A0054DU

      Remove the panel register. Then disconnect the connector and detach the clamp.

  15. REMOVE INSTRUMENT SIDE PANEL LH


    1. A0053INE01
      Text in Illustration
      *1 Protective Tape

      Place protective tape as shown in the illustration.

    2. Using a moulding remover B, detach the 3 clips and 4 claws.

    3. A0055NH

      Detach the 2 hooks and remove the side panel.

  16. REMOVE INSTRUMENT SIDE PANEL RH


    1. A0057EYE01
      Text in Illustration
      *1 Protective Tape

      Place protective tape as shown in the illustration.

    2. Using a moulding remover B, detach the 3 clips and 4 claws.

    3. A00577VE01
      Text in Illustration
      *1 w/ Airbag Cut Off Switch Cylinder

      w/ Airbag Cut Off Switch Cylinder:


      1. Disconnect the connector.

    4. Detach the 2 hooks and remove the side panel.

  17. REMOVE FRONT PILLAR GARNISH LH (for Sedan)

    Click here

  18. REMOVE FRONT PILLAR GARNISH LH (for Wagon)

    Click here

  19. REMOVE FRONT PILLAR GARNISH RH (for Sedan)

    Click here

  20. REMOVE FRONT PILLAR GARNISH RH (for Wagon)

    Click here

  21. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

    Click here

  22. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY (for 11 Speakers)


    1. A0052A9

      Detach the 2 clips and 4 claws and remove the speaker panel.

  23. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

    Tech Tips

    Use the same procedure described for the No. 2 instrument panel speaker panel.

  24. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY (for 11 Speakers)

    Tech Tips

    Use the same procedure described for the No. 2 instrument panel speaker panel.

  25. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY


    1. Remove the passenger airbag bolt <A>.

    2. Disconnect the connectors and clamps.

      A0058EBE01
      *1 for 11 Speakers:

    3. Remove the 3 screws <B>.

    4. Pull up the instrument panel to detach the 8 claws and 4 clips and remove the instrument panel.

      Note

      Be careful not to damage the steering wheel.

      A0058BI

  26. REMOVE GLOVE COMPARTMENT DOOR LOCK CYLINDER ASSEMBLY

    A0058FVE01
    Text in Illustration
    *1 Protective Tape
    *2 Stopper

    1. Using a screwdriver, push the stopper of the glove compartment door lock cylinder as shown in the illustration and remove the glove compartment door lock cylinder in the direction of the arrow.

      Tech Tips

      Tape the screwdriver tip before use.