ROOF HEADLINING(for Sedan) REMOVAL

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE FRONT SEAT ASSEMBLY LH


    1. for Manual Seat:

      Remove the front seat assembly Click here.

    2. for Power Seat:

      Remove the front seat assembly Click here.

  4. REMOVE FRONT SEAT ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  5. REMOVE REAR BENCH TYPE SEAT CUSHION ASSEMBLY

    Click here

  6. REMOVE REAR SIDE SEATBACK ASSEMBLY LH

    Click here

  7. REMOVE REAR SIDE SEATBACK ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  8. REMOVE FRONT DOOR SCUFF PLATE LH

    A0056JY

    1. Detach the 8 claws and 2 clips, and remove the front door scuff plate.

  9. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  10. REMOVE COWL SIDE TRIM BOARD LH

    A00545O

    1. Detach the clip, claw and guide, and remove the cowl side trim board.

  11. REMOVE COWL SIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure described for the LH side.

  12. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    A00583T

    1. Remove the front door opening trim weatherstrip.

  13. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  14. REMOVE REAR DOOR SCUFF PLATE LH

    A0053PU

    1. Detach the 6 claws and clip, and remove the rear door scuff plate.

  15. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  16. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

    A0052RV

    1. Remove the rear door opening trim weatherstrip.

  17. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  18. REMOVE FRONT PILLAR GARNISH LH

    A00572DE02
    Text in Illustration
    *1 Front Pillar Garnish Clip

    1. Pull the upper part of the garnish toward the inside of the cabin and detach the 2 clips.

      Tech Tips

      Make the front pillar garnish hang down from the front pillar garnish clip.

    2. A0058Z5E02
      Text in Illustration
      *1 Front Pillar Garnish Clip

      Cut the front pillar garnish clip.

    3. Detach the 2 guides and remove the front pillar garnish.

    4. Using a clip remover, remove the remaining front pillar garnish clip on the body side.

    5. A0058BQE01
      Text in Illustration
      *1 Curtain Shield Airbag Assembly
      *2 Adhesive Tape
      *3 Protective Tape

      w/ Curtain Shield Airbag:

      Protect the curtain shield airbag assembly.


      1. Completely cover the airbag with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.

        Note

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

  19. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  20. REMOVE LOWER CENTER PILLAR GARNISH LH

    A0058Y2

    1. Detach the 2 claws and 3 clips, and remove the lower center pillar garnish.

  21. REMOVE LOWER CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  22. REMOVE LAP BELT OUTER ANCHOR COVER

    A0053YN

    Tech Tips

    Use the same procedure for the other lap belt outer anchor cover.


    1. Detach the 3 claws and remove the lap belt outer anchor cover.

  23. REMOVE CENTER PILLAR GARNISH LH

    A0056VK

    1. Remove the bolt and disconnect the front seat outer belt floor anchor.

    2. A005607

      Remove the 2 screws.

    3. Detach the clip.

    4. Pass the front seat outer belt floor anchor through the center pillar garnish, and remove the center pillar garnish.

  24. REMOVE CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  25. REMOVE INNER ROOF SIDE GARNISH LH

    A0057YRE01
    Text in Illustration
    *1 Clip A

    1. Detach the 5 clips and remove the inner roof side garnish.

      Tech Tips

      The 2 clips labeled A remain attached to the body.

    2. Remove the 2 clips labeled A from the vehicle body.

  26. REMOVE INNER ROOF SIDE GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  27. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY

    Tech Tips


    • Use the same procedure for RHD and LHD vehicles.

    • The procedure listed below is for LHD vehicles.


    1. Remove the upper instrument panel sub-assembly Click here.

  28. REMOVE CONSOLE BOX ASSEMBLY


    1. Remove the console box assembly Click here.

  29. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

    Tech Tips


    • Use the same procedure for RHD and LHD vehicles.

    • The procedure listed below is for LHD vehicles.


    1. Remove the lower instrument panel sub-assembly Click here.

  30. REMOVE MAP LIGHT ASSEMBLY

    A0059KX

    1. Using a moulding remover, detach the 4 clips.

    2. Disconnect the connector and remove the map light.

  31. REMOVE NO. 1 ROOM LIGHT ASSEMBLY

    A0059B5

    1. Detach the 4 claws.

    2. Disconnect the connector and remove the No. 1 room light.

  32. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

    Click here

  33. REMOVE RAIN SENSOR COVER (w/ Rain Sensor)

    Click here

  34. REMOVE NO. 2 PRE-CRASH SAFETY CITY COVER (w/ Pre-crash Safety System)

    Click here

  35. REMOVE PRE-CRASH SAFETY CITY COVER

    Click here

  36. REMOVE VISOR ASSEMBLY LH


    1. A0054VZ

      Insert moulding remover A under the visor cover from the rear of the vehicle and detach the 2 claws.

    2. A0057FQ

      Insert moulding remover A under the visor cover from the front of the vehicle and detach the 2 claws.

    3. A0054N8

      Move the visor cover downward and release the 2 clip locks.

      Tech Tips

      Move the visor cover downward until the 2 clips are in the condition shown in the illustration.

    4. A00556Y

      Detach the 2 clips and remove the visor assembly LH.

      Tech Tips

      While pulling downward, move the visor assembly LH to the left and right slightly to detach the 2 clips.

    5. A0058DOE01
      Text in Illustration
      *1 Protective Tape

      When clip remains on vehicle:

      Using needle-nose pliers, pinch the clip and remove it.

      Tech Tips

      Tape the tips of the needle-nose pliers before use.

  37. REMOVE VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  38. REMOVE VISOR HOLDER

    A005821E01

    Tech Tips

    Use the same procedure for the other visor holder.


    1. Turn the visor holder clockwise approximately 45° and pull it out as shown in the illustration.

    2. Detach the 2 claws and remove the visor holder.

  39. REMOVE ASSIST GRIP SUB-ASSEMBLY

    A00593JE12

    Tech Tips

    Use the same procedure for the other assist grip.


    1. Using a clip remover, detach the 4 claws.

      Note

      Do not forcibly pry the assist grip plugs to prevent them from being deformed.

      Tech Tips


      • Gently pry on the assist grip plugs as shown in the illustration to remove them.

      • Tape the clip remover tip before use.

      Text in Illustration
      *1 Protective Tape
    2. A0055F4

      Pull off the 2 assist grip plugs by hand.

    3. Detach the 2 clips and remove the assist grip.

    4. Remove the 2 clips from the vehicle body.

  40. REMOVE REAR ASSIST GRIP ASSEMBLY LH

    A0053QUE07

    1. Using a clip remover, detach the 4 claws.

      Note

      Do not forcibly pry the assist grip plugs to prevent them from being deformed.

      Tech Tips


      • Gently pry on the assist grip plugs as shown in the illustration to remove them.

      • Tape the clip remover tip before use.

      Text in Illustration
      *1 Protective Tape
    2. A0057CK

      Pull off the 2 assist grip plugs by hand.

    3. Detach the 2 clips and remove the rear assist grip.

    4. Remove the 2 clips from the vehicle body.

  41. REMOVE REAR ASSIST GRIP ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  42. REMOVE SUNSHADE TRIM HOLDER


    1. A0055JAE01
      Text in Illustration
      *A w/o Rear Sunshade
      *B w/ Rear Sunshade
      *1 Pin

      Turn the pin and remove the sunshade trim holder.

  43. REMOVE ROOF HEADLINING ASSEMBLY

    A00534W

    1. w/ EC Mirror:

      Disconnect the EC mirror connector.

    2. A0055UF

      w/ Rain Sensor:

      Disconnect the rain sensor connector.

    3. A0052UN

      w/ Pre-crash Safety System:

      Disconnect the pre-crash safety city sensor connector.

    4. A0058T6

      Disconnect the connector and 3 clamps from the front pillar RH.

    5. A00547D

      Remove the 2 bolts.

    6. A00589A

      w/ Digital Audio Broadcasting Antenna:

      Disconnect the connector and detach the wire harness clamp from the rear pillar LH.

    7. Disconnect the 3 connectors and clamp from the rear pillar RH.

    8. A0056MU

      Disconnect the 4 clamps from the front pillar LH.

    9. for LHD:


      1. A0052KQE02
        Text in Illustration
        *A for LHD

        Disconnect the 2 clamps.

      2. A005602E02
        Text in Illustration
        *A for LHD

        Disconnect the 2 roof wire connectors.

    10. for RHD:


      1. A005355E02
        Text in Illustration
        *A for RHD

        Disconnect the 2 clamps and roof wire connector.

      2. A00546NE02
        Text in Illustration
        *A for RHD

        Disconnect the roof wire connector.

    11. Detach the clip.

      A00547J
    12. A0058C3E01
      Text in Illustration
      *A for LHD
      *B for RHD

      Remove the roof headlining from the passenger door as shown in the illustration.

      Note

      Be careful not to damage the roof headlining when taking it out.

  44. REMOVE FRONT DOOR SCUFF PLATE OUTSIDE LH

    A0053IVE02
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the front door scuff plate outside.

    2. Using a moulding remover, detach the 3 clips and remove the front door scuff plate outside.

  45. REMOVE FRONT DOOR SCUFF PLATE OUTSIDE RH

    Tech Tips

    Use the same procedure described for the LH side.

  46. REMOVE REAR DOOR SCUFF PLATE OUTSIDE LH

    A0058CRE02
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the rear door scuff plate outside.

    2. Using a moulding remover, detach the 2 clips and remove the rear door scuff plate outside.

  47. REMOVE REAR DOOR SCUFF PLATE OUTSIDE RH

    Tech Tips

    Use the same procedure described for the LH side.

  48. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

    A0054BF

    1. Detach the 5 claws and remove the front shoulder belt anchor plate.

  49. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  50. REMOVE REAR NO. 2 SIDE RAIL SPACER LH

    A0054RK

    1. Detach the 2 claws and remove the No. 2 side rail spacer.

  51. REMOVE REAR NO. 2 SIDE RAIL SPACER RH

    Tech Tips

    Use the same procedure described for the LH side.