METER / GAUGE SYSTEM Speed Signal Circuit

DESCRIPTION

The vehicle speed sensor signal consists of pulses sent to the combination meter assembly from the skid control ECU.

WIRING DIAGRAM

A0053VGE02

PROCEDURE


  1. CHECK ECU TERMINAL VOLTAGE (INPUT VOLTAGE)


    1. A0054GLE01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Combination Meter Assembly)

      Disconnect the D66 combination meter assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      D66-3 (+S) - Body ground Ignition switch ON 4.5 to 14 V

      Tech Tips

      If any of the ECUs specified in the wiring diagram supplies power to the combination meter assembly, the combination meter assembly will output a waveform.


    NG

    CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 3 JUNCTION BLOCK) Click here

    OK

  2. CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)


    1. A0054ZGE02
      Text in Illustration
      *A except CVT
      *B for CVT
      *a

      Front view of wire harness connector

      (to Brake Actuator Assembly [Skid Control ECU])
      *b

      Front view of wire harness connector

      (to Brake Actuator Assembly [Skid Control ECU])

      Disconnect the A42*1 or A43*2 brake actuator assembly (skid control ECU) connector.


      • *1: except CVT

      • *2: for CVT

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      except CVT
      Tester Connection Switch Condition Specified Condition
      A42-33 (SP1) - Body ground Ignition switch ON 11 to 14 V
      for CVT
      Tester Connection Switch Condition Specified Condition
      A43-33 (SP1) - Body ground Ignition switch ON 11 to 14 V

    NG

    CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - SKID CONTROL ECU) Click here

    OK

  3. CHECK COMBINATION METER ASSEMBLY (SPEED SIGNAL)


    1. A0053HIE01
      Text in Illustration
      *a

      Component with harness connected

      (Combination Meter Assembly)

      Check the input waveform.


      1. Reconnect the D66 combination meter assembly connector.

      2. Remove the combination meter assembly with the connector(s) still connected.

      3. Connect an oscilloscope to terminal D66-5 (SI) and body ground.

      4. Turn the ignition switch to ON.

      5. Turn the wheel slowly.

      6. Check the signal waveform according to the condition(s) in the table below.

        Measurement Condition
        Item Condition
        Terminal No. (Symbols) D66-5 (SI) - Body ground
        Tool setting 5 V/DIV., 20 ms./DIV.
        Condition Being driven at approximately 20 km/h (12 mph)
        OK
        The waveform is displayed as shown in the illustration.

        Tech Tips

        When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.


    OK

    REPLACE COMBINATION METER ASSEMBLY Click here

    NG

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here

  4. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - SKID CONTROL ECU)


    1. Disconnect the D66 combination meter assembly connector.

      A0052HRE01

    2. Disconnect the A42*1 or A43*2 brake actuator assembly (skid control ECU) connectors.


      • *1: except CVT

      • *2: for CVT

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      except CVT
      Tester Connection Condition Specified Condition
      D66-5 (SI) - A42-33 (SP1) Always Below 1 Ω
      A42-33 (SP1) - Body ground Always 10 kΩ or higher
      for CVT
      Tester Connection Condition Specified Condition
      D66-5 (SI) - A43-33 (SP1) Always Below 1 Ω
      A43-33 (SP1) - Body ground Always 10 kΩ or higher
      Text in Illustration
      *A except CVT
      *B for CVT
      *a

      Front view of wire harness connector

      (to Combination Meter Assembly)
      *b

      Front view of wire harness connector

      (to Brake Actuator Assembly [Skid Control ECU])
      *c

      Front view of wire harness connector

      (to Brake Actuator Assembly [Skid Control ECU])

    OK

    REPLACE COMBINATION METER ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  5. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 3 JUNCTION BLOCK)


    1. Disconnect the D66 combination meter assembly connector.

      A0052KWE01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 3 Junction Block)

      		 *b

      Front view of wire harness connector

      (to Combination Meter Assembly)

    2. Disconnect the 3B junction block connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      D66-3 (+S) - 3B-18 Always Below 1 Ω
      D66-3 (+S) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. CHECK POWER MANAGEMENT CONTROL ECU

    Note

    For vehicles without entry and start system, go to "Check Radio Receiver Assembly".


    1. Disconnect the 3B junction block connector.

      A0057EJE01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 3 Junction Block)

      		 - -

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      3B-7 - Body ground Ignition switch ON 4.5 to 14 V

    NG

    CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU CIRCUIT) Click here

    OK

  7. CHECK RADIO RECEIVER ASSEMBLY

    Note

    For vehicles without radio receiver assembly, go to "Check Radio and Display Receiver Assembly".


    1. Disconnect the 3A junction block connector.

      A0056G1E01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 3 Junction Block)

      		 - -

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      3A-21 - Body ground Ignition switch ON 4.5 to 14 V

    NG

    CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY CIRCUIT) Click here

    OK

  8. CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

    Note

    For vehicles without radio and display receiver assembly, go to "Check Tire Pressure Monitor Receiver Assembly".


    1. Disconnect the 3A junction block connector.

      A0056G1E01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 3 Junction Block)

      		 - -

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      3A-21 - Body ground Ignition switch ON 4.5 to 14 V

    NG

    CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY CIRCUIT) Click here

    OK

  9. CHECK TIRE PRESSURE MONITOR RECEIVER ASSEMBLY

    Note

    For vehicles without tire pressure warning system, go to "Check ECM".


    1. Disconnect the 3A junction block connector.

      A00550TE01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 3 Junction Block)

      		 - -

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      3A-44 - Body ground Ignition switch ON 4.5 to 14 V

    NG

    CHECK HARNESS AND CONNECTOR (TIRE PRESSURE MONITOR RECEIVER ASSEMBLY CIRCUIT) Click here

    OK

  10. CHECK ECM


    1. Disconnect the 3A junction block connector.

      A0052YME02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 3 Junction Block)

      		 - -

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      3A-20 - Body ground Ignition switch ON 4.5 to 14 V

    OK

    REPLACE NO. 3 JUNCTION BLOCK

    NG

    CHECK HARNESS AND CONNECTOR (ECM CIRCUIT) Click here

  11. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU CIRCUIT)


    1. Disconnect the 3B junction block connector.

      A0058CBE01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 3 Junction Block)

      		 *b

      Front view of wire harness connector

      (to Power Management Control ECU)

    2. Disconnect the D109 power management control ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      D109-23 (SPD) - 3B-7 Always Below 1 Ω
      3B-7 - Body ground Always 10 kΩ or higher

    OK

    REPLACE POWER MANAGEMENT CONTROL ECU Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  12. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY CIRCUIT)


    1. Disconnect the 3A junction block connector.

      A0058YFE01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 3 Junction Block)

      		 *b

      Front view of wire harness connector

      (to Radio Receiver Assembly)

    2. Disconnect the D119 radio receiver assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      D119-17 (SPD) - 3A-21 Always Below 1 Ω
      3A-21 - Body ground Always 10 kΩ or higher

    OK

    REPLACE RADIO RECEIVER ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  13. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY CIRCUIT)


    1. Disconnect the 3A junction block connector.

      A0052K6E01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 3 Junction Block)

      		 *b2

      Front view of wire harness connector

      (to Navigation Receiver Assembly)

    2. Disconnect the D124 radio and display receiver connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      D124-17 (SPD) - 3A-21 Always Below 1 Ω
      3A-21 - Body ground Always 10 kΩ or higher

    OK

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  14. CHECK HARNESS AND CONNECTOR (TIRE PRESSURE MONITOR RECEIVER ASSEMBLY CIRCUIT)


    1. Disconnect the 3A junction block connector.

      A0055J7E02
      Text in Illustration
      *A for Sedan *B for Wagon
      *a

      Front view of wire harness connector

      (to No. 3 Junction Block)

      		 *b

      Front view of wire harness connector

      (to Tire Pressure Monitor Receiver Assembly)

    2. Disconnect the G58*1 or L1*2 tire pressure monitor receiver assembly connector.


      • *1: for Sedan

      • *2: for Wagon

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for Sedan
      Tester Connection Condition Specified Condition
      G58-2 (SPD) - 3A-44 Always Below 1 Ω
      3A-44 - Body ground Always 10 kΩ or higher
      for Wagon
      Tester Connection Condition Specified Condition
      L1-2 (SPD) - 3A-44 Always Below 1 Ω
      3A-44 - Body ground Always 10 kΩ or higher
      Result
      Result Proceed to
      OK (for Sedan) A
      OK (for Wagon) B
      NG C

    A

    REPLACE TIRE PRESSURE MONITOR RECEIVER ASSEMBLY Click here

    B

    REPLACE TIRE PRESSURE MONITOR RECEIVER ASSEMBLY Click here

    C

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  15. CHECK HARNESS AND CONNECTOR (ECM CIRCUIT)


    1. Disconnect the 3A junction block connector.

      A0052JLE01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 3 Junction Block)

      		 *b

      Front view of wire harness connector

      (to ECM)

    2. Disconnect the A40 ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A40-38 (SPD) - 3A-20 Always Below 1 Ω
      3A-20 - Body ground Always 10 kΩ or higher
      Result
      Result Proceed to
      OK (for 1ZR-FAE) A
      OK (for 2ZR-FAE) B
      OK (for 3ZR-FE) C
      OK (for 3ZR-FAE) D
      NG E

    A

    REPLACE ECM Click here

    B

    REPLACE ECM Click here

    C

    REPLACE ECM Click here

    D

    REPLACE ECM Click here

    E

    REPAIR OR REPLACE HARNESS OR CONNECTOR