AUDIO AND VISUAL SYSTEM(for Radio and Display Type) Reverse Signal Circuit

DESCRIPTION

The radio and display receiver assembly receives a reverse signal from the park/neutral position switch assembly to use for adjusting the vehicle position on the multi-display.

WIRING DIAGRAM

A0055K2E03

CAUTION / NOTICE / HINT

Note

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. CHECK VEHICLE SIGNAL (OPERATION CHECK)


    1. A005787

      Enter the "Vehicle Signal Check Mode" screen. [Refer to Check Vehicle Signal Check Mode in Operation Check Click here]

    2. Check that the display changes between ON and OFF according to the shift lever position.

      OK
      Shift Lever Position Display
      R ON
      Except R OFF

      Tech Tips

      This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.


    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

  2. CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY


    1. A0057T1E02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Radio and Display Receiver Assembly)

      Disconnect the radio and display receiver assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      D124-2 (REV) - Body ground Ignition switch ON, shift lever in R 7.5 to 14 V
      D124-2 (REV) - Body ground Ignition switch ON, shift lever not in R Below 1 V
      Result
      Result Proceed to
      OK A
      NG (except Manual Transaxle) B
      NG (for Manual Transaxle) C

    A

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY Click here

    C

    CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY) Click here

    B

  3. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)


    1. Disconnect the D124 radio and display receiver assembly connector.

    2. Disconnect the B14 park/neutral position switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for Automatic Transaxle
      Tester Connection Condition Specified Condition
      D124-2 (REV) - B14-1 (RL) Always Below 1 Ω
      D124-2 (REV) - Body ground Always 10 kΩ or higher
      for CVT
      Tester Connection Condition Specified Condition
      D124-2 (REV) - B14-2 (RL) Always Below 1 Ω
      D124-2 (REV) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)


    1. A0053Q7E02
      Text in Illustration
      *A for Automatic Transaxle
      *B for CVT
      *a

      Front view of wire harness connector

      (to Park/neutral Position Switch Assembly)

      Disconnect the park/neutral position switch assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      for Automatic Transaxle
      Tester Connection Switch Condition Specified Condition
      B14-2 (RB) - Body ground Ignition switch ON 11 to 14 V
      for CVT
      Tester Connection Switch Condition Specified Condition
      B14-1 (RB) - Body ground Ignition switch ON 11 to 14 V
      Result
      Result Proceed to
      OK (for Automatic Transaxle) A
      OK (for CVT [K111]) B
      OK (for CVT [K311]) C
      NG D

    A

    REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY Click here

    B

    REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY Click here

    C

    REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY Click here

    D

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  5. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY)


    1. Disconnect the D124 radio and display receiver assembly connector.

    2. Disconnect the B5 back-up light switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      D124-2 (REV) - B5-1 (RL) Always Below 1 Ω
      D124-2 (REV) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. CHECK HARNESS AND CONNECTOR (BACK-UP LIGHT SWITCH ASSEMBLY - BATTERY)


    1. A0053XSE02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Back-up Light Switch Assembly)

      Disconnect the back-up light switch assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      B5-2 (RB) - Body ground Ignition switch ON 11 to 14 V
      Result
      Result Proceed to
      OK (for Manual Transaxle [EB60]) A
      OK (for Manual Transaxle [EC60]) B
      NG C

    A

    REPLACE BACK-UP LIGHT SWITCH ASSEMBLY Click here

    B

    REPLACE BACK-UP LIGHT SWITCH ASSEMBLY Click here

    C

    REPAIR OR REPLACE HARNESS OR CONNECTOR