SFI SYSTEM, Diagnostic DTC:P2111, P2112

DTC Code DTC Name
P2111 Throttle Actuator Control System - Stuck Open
P2112 Throttle Actuator Control System - Stuck Closed

DESCRIPTION

The throttle actuator is operated by the ECM, and opens and closes the throttle valve using gears. The opening angle of the throttle valve is detected by the throttle position sensor, which is built into the throttle body assembly. The throttle position sensor provides feedback to the ECM in order to control the throttle actuator, and therefore the throttle valve, appropriately in response to driver inputs.

Tech Tips

This electronic throttle control system does not use a throttle cable.

DTC No. DTC Detection Condition Trouble Area
P2111 ECM signals throttle actuator to close, but the actuator is stuck (1 trip detection logic).

  • Throttle actuator

  • Throttle body assembly

  • Throttle valve

  • ECM

  • Wire harness or connector
P2112 ECM signals throttle actuator to open, but the actuator is stuck (1 trip detection logic).

  • Throttle actuator

  • Throttle body assembly

  • Throttle valve

  • ECM

  • Wire harness or connector

FAIL-SAFE

When either of these DTCs or other DTCs relating to electronic throttle control system malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 5.5° opening angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal position, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed gently, the vehicle can be driven slowly. Fail-safe mode continues until a pass condition is detected and the ignition switch is turned off.

WIRING DIAGRAM

Refer to DTC P2102 Click here.

CAUTION / NOTICE / HINT

Tech Tips

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2111 OR P2112)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    5. Read DTCs.

      Result
      Result Proceed to
      P2111 or P2112 is output A
      P2111 or P2112 and other DTCs are output B

      Tech Tips

      If any DTCs other than P2111 or P2112 are output, troubleshoot those DTCs first.


    B

    GO TO DTC CHART Click here

    A

  2. INSPECT THROTTLE BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)


    1. Check for contamination between the throttle valve and housing. If necessary, clean the throttle body assembly. Also, check that the throttle valve moves smoothly.

      OK
      Throttle valve is not contaminated with foreign objects and moves smoothly.

      Tech Tips

      Perform "Inspection After Repair" after cleaning the throttle body assembly Click here.


    NG

    REPLACE THROTTLE BODY ASSEMBLY Click here

    OK

  3. READ VALUE USING GTS (THROTTLE POSITION)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Clear the DTCs Click here.

    5. Turn the ignition switch off and wait for at least 30 seconds.

    6. Turn the ignition switch to ON.

    7. Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Position No. 1, Throttle Position No. 2 and Throttle Position Command.

    8. Check the values displayed on the GTS while wiggling the ECM wire harness.

    9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    10. Check for DTCs.

      Result
      Result Proceed to
      Value in Data List changes when wire harness is wiggled, or DTC is output A
      Other than above B

    B

    CHECK WHETHER DTC OUTPUT RECURS (DTC P2111 OR P2112) Click here

    A

  4. REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - THROTTLE BODY ASSEMBLY)


    1. As the DTC was stored due to a change in the contact resistance of the connector, repair or replace the wire harness or connector Click here.


    NEXT

    END

  5. REPLACE THROTTLE BODY ASSEMBLY


    1. Replace the throttle body assembly Click here.

      Tech Tips

      Perform "Inspection After Repair" after replacing the throttle body assembly Click here.


    NEXT

  6. CHECK WHETHER DTC OUTPUT RECURS (DTC P2111 OR P2112)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Clear the DTCs Click here.

    5. Start the engine, and then fully depress and release the accelerator pedal quickly to fully open and close the throttle valve.

    6. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    7. Read the DTCs.

      Result
      Result Proceed to
      DTC is not output A
      DTC P2111 or P2112 is output B

    A

    END

    B

    REPLACE ECM Click here