POWER SWITCH REMOVAL


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.

  2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER


    1. A01HUM2

      Disengage the claw to remove the luggage trim service hole cover.

  3. DISCONNECT CABLE FROM AUXILIARY BATTERY NEGATIVE TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY

    Click here

  5. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY

    Click here

  6. REMOVE FRONT DOOR SCUFF PLATE LH


    1. A01HTTW

      Disengage the 10 claws and remove the front door scuff plate LH.

  7. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    1. A01HVSU

      Remove the clip.

    2. Pull the cowl side trim sub-assembly LH in the direction indicated by the arrow shown in the illustration to disengage the 2 clips and remove the cowl side trim sub-assembly LH.

  8. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. A01HSG5

      Disconnect the front door opening trim weatherstrip LH.

  9. REMOVE INSTRUMENT SIDE PANEL LH


    1. A01HTFQ

      Using a moulding remover, disengage the 4 claws as shown in the illustration.

    2. A01HT5Y

      Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.

  10. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. A01HSL0

      Disengage the 3 clips to remove the No. 1 instrument cluster finish panel garnish as shown in the illustration.

  11. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. A01HVJKE01
      Text in Illustration
      *1 Protective Tape

      Apply protective tape to the area shown in the illustration.

    2. A01HUXQ

      Disengage the 2 clips as shown in the illustration.

    3. A01HW8L

      Using a moulding remover, disengage the 2 clips to remove the No. 1 instrument panel register assembly.

  12. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    1. Operate the tilt and telescopic lever to fully extend and lower the steering column assembly.

    2. A01HTQ1

      Using a moulding remover, disengage the 2 claws, 4 clips and 2 guides.

    3. A01HSTJ

      Disengage the 5 claws, 5 clips and 2 guides.

    4. Disconnect each connector.

    5. A01HUIZ

      Remove the instrument cluster finish panel assembly as shown in the illustration.

  13. REMOVE FRONT PANEL GARNISH LH


    1. A01HU0I

      Disengage the 3 claws, 2 clips and 8 guides to remove the front panel garnish LH.

  14. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. A01HUD8

      Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.

  15. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    1. A01HTGO

      Remove the bolt <C> and screw <D> or <E>.

    2. A01HSR5

      Disengage the 4 claws, 9 clips and 3 guides to remove the lower No. 1 instrument panel finish panel assembly.

  16. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    1. A01HTO1

      Disengage the 4 clips and guide.

    2. Disconnect the connector and remove the lower instrument panel finish panel assembly.

  17. REMOVE POWER SWITCH


    1. A01HTWE

      Disengage the 2 claws and remove the power switch.