Click here

BACK WINDOW GLASS REMOVAL

Click here
Click here Click here
Tip:

When removing the moulding, heat the vehicle body and moulding using a heat light.

Heating temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Moulding 20 to 30°C (68 to 86°F)
Note:

Do not heat the vehicle body and moulding excessively.

Click here
  1. Click here

    PRECAUTION

    Note:

    After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery terminal notice before proceeding with work (Click here).

  2. Click here

    REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)

  3. Click here

    REMOVE DECK BOARD ASSEMBLY (w/o Spare Tire)

  4. Click here

    REMOVE DECK TRIM SIDE BOARD LH (w/o Spare Tire)


    1. A01GXQQ

      Detach the 2 clips and remove the deck trim side board LH.

  5. Click here

    REMOVE BATTERY SERVICE HOLE COVER LH


    1. A01GZIME02

      Detach the clip, fastening tape and remove the battery service hole cover LH.

      Table 1. Text in Illustration
      *A for Standard
      *B for Ottoman
      *1 Fastening Tape
  6. Click here

    DISCONNECT CABLE FROM AUXILIARY BATTERY NEGATIVE TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (see pageClick here).

  7. Click here

    REMOVE REAR SEAT ASSEMBLY


    1. for Power Seat:

      (Click here)

    2. for Ottoman:

      (Click here)

    3. for Fixed Seat Type:

      (Click here)

  8. Click here

    REMOVE REAR DOOR SCUFF PLATE LH


    1. for Standard Body:

      (Click here)

    2. for Long Body:

      (Click here)

  9. Click here

    REMOVE REAR DOOR SCUFF PLATE RH


    1. for Standard Body:

      (Click here)

    2. for Long Body:

      (Click here)

  10. Click here

    REMOVE REAR SEAT SIDE GARNISH LH


    1. Detach the 6 claws and remove the rear seat side garnish LH.

  11. Click here

    REMOVE REAR SEAT SIDE GARNISH RH

    Tip:

    Use the same procedure described for the LH side.

  12. Click here

    REMOVE INNER ROOF SIDE GARNISH LH


    1. Pull the inner roof side garnish LH away from the body to detach the 4 clips (do not detach clip A).

      Table 2. Text in Illustration
      *1 Clip A

    2. Detach the 2 claws of the guide, and pull the inner roof side garnish LH in the direction of the arrow to remove it.

      Tip:

      Clip A remains attached to the body.

    3. Remove clip A from the vehicle body.

  13. Click here

    REMOVE INNER ROOF SIDE GARNISH RH

    Tip:

    Use the same procedure described for the LH side.

  14. Click here

    REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY


    1. A01GWDN

      except 4-Passenger with Ottoman:

      Using a moulding remover D, detach the 4 claws and remove the 3 belt guides.

    2. for 4-Passenger with Ottoman:

      Using a moulding remover D, detach the 4 claws and remove the 2 belt guides.

    3. A01GY1H

      except 4-Passenger with Ottoman:

      Detach the 2 clips of the package tray trim panel assembly. Then pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.

    4. A01H1AU

      for 4-Passenger with Ottoman:

      Detach the 2 clips of the package tray trim panel assembly. Then pass the 2 rear seat belt floor anchors through the package tray trim panel assembly.

    5. Disconnect the solar sensor connector and remove the package tray trim panel.

  15. Click here

    REMOVE NO. 2 PACKAGE TRAY TRIM PANEL ASSEMBLY


    1. Detach the 5 claws and 3 clips, and remove the No. 2 package tray trim panel assembly.

  16. Click here

    REMOVE ROOF CONSOLE BOX ASSEMBLY (w/ Rear Seat Entertainment System)


    1. A01H1FP

      w/o Sliding Roof:


      1. Remove the 2 screws.

      2. Detach the 6 clips, 2 claws and 2 hooks and remove the roof console box assembly.

      3. Disconnect the connector.

    2. A01GZTU

      w/ Sliding Roof:


      1. Remove the 2 screws.

      2. Detach the 6 clips and 2 hooks and remove the roof console box assembly.

      3. Disconnect the connector.

  17. Click here

    REMOVE SPOT LIGHT ASSEMBLY (w/o Rear Seat Entertainment System)


    1. Detach the 4 claws and remove the spot light lens.

  18. Click here

    REMOVE REAR VANITY LIGHT ASSEMBLY

    Tip:

    Use the same procedure to remove the vanity light on the other side.


    1. Using a screwdriver, detach the 4 claws and remove the lens.

      Tip:

      Tape the screwdriver tip before use.

    2. Remove the 2 screws.

    3. Using moulding remover D, detach the claw and remove the vanity light assembly.

    4. A01H0BME02

      Disconnect the connector.

      Table 3. Text in Illustration
      *1 Protective Tape - -
  19. Click here

    REMOVE COAT HOOK

    Tip:

    Use the same procedure to remove the hook on the other side.


    1. Remove the screw and coat hook.

  20. Click here

    REMOVE ROOF SIDE REGISTER BEZEL LH (w/ Rear Cooler)


    1. Remove the screw.

    2. Detach the claw and remove the roof side register LH.

  21. Click here

    REMOVE ROOF SIDE REGISTER BEZEL RH (w/ Rear Cooler)

    Tip:

    Use the same procedure described for the LH side.

  22. Click here

    REMOVE ASSIST GRIP SUB-ASSEMBLY

    Tip:

    Use the same procedure for all the assist grips.


    1. Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

      Tip:

      Tape the screwdriver tip before use.

      Table 4. Text in Illustration
      *1 Protective Tape

    2. Detach the 2 clips and remove the assist grip sub-assembly.

  23. Click here

    REMOVE ROOF HEADLINING ASSEMBLY


    1. for Standard Body:

      Tip:

      It is not necessary to completely remove the roof headlining. Slightly lower the rear section of the roof headlining (Click here) so that the back window glass can be removed in a later step.

    2. for Long Body:

      Tip:

      It is not necessary to completely remove the roof headlining. Slightly lower the rear section of the roof headlining (Click here) so that the back window glass can be removed in a later step.

  24. Click here

    REMOVE AMPLIFIER ANTENNA ASSEMBLY


    1. Disconnect each connector.

    2. Detach the 4 clamps labeled A and remove the 2 nuts labeled B.

    3. A01GYQ1E01

      Detach the clip labeled C and remove the amplifier antenna.

      Tip:

      • Remove the clip if it is damaged.

      • The clip is used when the vehicle is assembled at the factory and is not needed for the reinstallation.

  25. Click here

    REMOVE CENTER ROOF DRIP SIDE FINISH MOULDING LH


    1. Put protective tape around the center roof drip side finish moulding.

    2. A01GX5D

      for Standard Body:

      Using a moulding remover, detach the 16 clips and remove the center roof drip side finish moulding LH.

    3. A01H0HB

      for Long Body:

      Using a moulding remover, detach the 17 clips and remove the center roof drip side finish moulding.

      Note:

      • Do not remove the clips from the vehicle body.

      • If the clips are damaged or removed accidentally, replace them.

  26. Click here

    REMOVE CENTER ROOF DRIP SIDE FINISH MOULDING RH

    Tip:

    Use the same procedures described for the LH side.

  27. Click here

    REMOVE NO. 2 WINDSHIELD OUTSIDE MOULDING CLIP

    Tip:

    Perform the following procedure if replacing the No. 2 outside windshield moulding clip.


    1. Remove the No. 2 outside windshield moulding clip.

    2. Remove the No. 2 moulding clip.

  28. Click here

    REMOVE NO. 1 WINDSHIELD OUTSIDE MOULDING CLIP

    Tip:

    Use the same procedures described for the No. 2 windshield outside moulding clip.

  29. Click here

    REMOVE NO. 2 ROOF DRIP SIDE FINISH MOULDING CLIP

    Tip:

    Perform the following procedure if replacing the No. 2 roof drip side finish moulding clips.


    1. A01H0IX

      Remove the 9 No. 2 roof drip side finish moulding clips.

  30. Click here

    REMOVE NO. 3 WINDSHIELD OUTSIDE MOULDING CLIP

    Tip:

    Perform the following procedure if replacing the No. 3 outside windshield moulding clip.


    1. Put a 4 mm (0.16 in.) drill bit into a drill.

    2. Wind tape around the drill bit approximately 5 mm (0.20 in.) from the tip of the drill.

      Tip:

      Tape the 4 mm (0.16 in.) drill bit to prevent the drill bit from going too deep.

    3. A01GWK3E03

      Lightly press the drill against the rivets, drill off the flanges of the rivets, and remove the 10 rivets.

      Note:

      • Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

      • Do not pry the rivets with the drill, because this may cause damage to the installation holes of the rivets or the drill bit.

      • Be careful of the drilled rivets as they may become hot.

      Table 5. Text in Illustration
      *a Front Side *b Rear Side

    4. Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.

  31. Click here

    REMOVE NO. 1 ROOF DRIP SIDE FINISH MOULDING CLIP

    Tip:

    Perform the following procedure if replacing the No. 1 roof drip side finish moulding clips.


    1. A01H0QU

      for Standard Body:

      Remove the 6 No. 1 roof drip side finish moulding clips.

    2. A01GYQ9

      for Long Body:

      Remove the 7 No. 1 roof drip side finish moulding clips.

  32. Click here

    REMOVE ROPE HOOK ASSEMBLY


    1. A01GWVA

      Remove the 4 bolts and 4 rope hook assemblies.

  33. Click here

    REMOVE ROPE HOOK


    1. A01GYPFE01

      Remove the 4 rope hooks by pushing the claws in the direction of the arrows in the illustration.

  34. Click here

    REMOVE DECK TRIM SIDE BOARD RH


    1. A01GX0VE03

      w/ Spare Tire:


      1. Remove the clip.

      2. Remove the deck trim side board RH.

    2. w/o Spare Tire:


      1. Detach the clip and remove the deck trim side board RH.

        Table 6. Text in Illustration
        *A w/ Spare Tire
        *B w/o Spare Tire
  35. Click here

    REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY


    1. Using a screwdriver, detach the 2 claws and remove the No. 1 luggage compartment light assembly.

      Tip:

      Tape the screwdriver tip before use.

      Table 7. Text in Illustration
      *1 Protective Tape

    2. Disconnect the connector.

  36. Click here

    REMOVE NO. 1 COOLER COVER (w/ Rear Cooler)


    1. A01GZDY

      Detach the 5 clips and remove the No. 1 cooler cover.

  37. Click here

    REMOVE FRONT LUGGAGE COMPARTMENT TRIM COVER


    1. A01GZ3DE02

      Remove the 3 clips.

    2. Detach the 4 claws and remove the front luggage compartment trim cover.

      Table 8. Text in Illustration
      *A w/o Rear Cooler
      *B w/ Rear Cooler
  38. Click here

    REMOVE REAR FLOOR FINISH PLATE


    1. A01GW5P

      Remove the 3 clips.

    2. Detach the 4 clips and remove the rear floor finish plate.

  39. Click here

    REMOVE LOWER BACK WINDOW MOULDING OUTSIDE


    1. A01GZK7E01

      Using a screwdriver, detach the 2 claws, 4 fasteners and double-sided tape (3 areas). Slide the moulding toward the front of the vehicle along the back window glass to detach the clip. Then remove the moulding.

      Note:

      • Be careful not to damage the vehicle body.

      • Do not lift the moulding or slide it toward the rear of the vehicle when detaching the clip.

      • The moulding is a non-reusable part.

      Tip:

      Tape the screwdriver tip before use.

  40. Click here

    REMOVE LUGGAGE COMPARTMENT TRIM COVER ASSEMBLY LH


    1. A01H0Y9

      Remove the 2 clips.

    2. Detach the claw and luggage compartment trim cover assembly LH.

  41. Click here

    REMOVE LUGGAGE COMPARTMENT TRIM COVER ASSEMBLY RH


    1. A01H0XJ

      Remove the 2 clips.

    2. Detach the claw and luggage compartment trim cover assembly RH.

  42. Click here

    REMOVE REAR COMBINATION LIGHT ASSEMBLY LH


    1. Put protective tape around the rear combination light assembly LH.

    2. Disconnect the connector.

    3. Remove the 3 nuts.

    4. A01GW6ZE02

      Move the rear combination light assembly LH in the direction of the arrow in the illustration, detach the clip, 2 claws and 2 guides to remove the rear combination light assembly LH.

      Tip:

      The clips remain on the vehicle body.

      Table 9. Text in Illustration
      *1 Protective Tape *2 Rear Combination Light Assembly LH
      *3 Clip - -
  43. Click here

    REMOVE REAR COMBINATION LIGHT ASSEMBLY RH

    Tip:

    Use the same procedure described for the LH side.

  44. Click here

    REMOVE LUGGAGE COMPARTMENT DOOR HINGE COVER LH


    1. A01H0SZE01

      Using a screwdriver, detach the double-sided tape (2 areas) and 2 clips. Then remove the hinge cover.

      Note:

      • If reusing the hinge cover, take care not to damage the hinge cover.

      • Be careful not to damage the vehicle body.

      • The hinge cover is a non-reusable part.

      Tip:

      Tape the screwdriver tip before use.

  45. Click here

    REMOVE LUGGAGE COMPARTMENT DOOR HINGE COVER RH

    Tip:

    Use the same procedures described for the LH side.

  46. Click here

    REMOVE CENTER NO. 2 STOP LIGHT COVER


    1. Push in the No. 2 center stop light cover at a point 10 mm (0.393 in.) from the end of the cover as shown in the illustration.

    2. A01GXQI

      With the No. 2 center stop light cover pushed in, slide it towards the outside of the vehicle to detach the 4 claws.

    3. A01H1U1

      Lift up the No. 2 center stop light cover to remove it as shown in the illustration.

  47. Click here

    REMOVE CENTER STOP LIGHT COVER


    1. Push in the center stop light cover at a point 10 mm (0.393 in.) from the end of the cover as shown in the illustration.

    2. A01H29S

      With the center stop light cover pushed in, slide it towards the outside of the vehicle to detach the 4 claws.

    3. A01GYBQ

      Lift up the center stop light cover to remove it as shown in the illustration.

  48. Click here

    REMOVE CENTER STOP LIGHT CLIP


    1. Turn the 2 center stop light clips 90° and remove them.

  49. Click here

    REMOVE CENTER STOP LIGHT ASSEMBLY


    1. Disconnect the harness and connector.

    2. A01GXMS

      Remove the 2 screws.

    3. Detach the 2 claws and remove the center stop light assembly.

  50. Click here

    REMOVE BACK WINDOW GLASS

    Note:

    As the stopper, bracket and harness are not supplied individually, be careful not to damage them when installing the back window glass.


    1. A01H1J5E01

      Apply protective tape to the outer surface of the vehicle body to prevent scratches.

      Note:

      When separating the back window glass from the vehicle, be careful not to damage the vehicle's paint or interior/exterior ornaments.

    2. A01GYVXE01

      From the interior, insert a piano wire between the vehicle body and back window glass as shown in the illustration.

      Note:

      • If the stopper is damaged, the back window glass assembly must be replaced. Be careful when performing the procedure.

      • Make sure not to deform the upper brackets.

      • Make sure not to damage the wire harness.

    3. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

    4. A01GWO8E01

      Place matchmarks over the glass and vehicle body on the locations indicated in the illustration.

      Tip:

      Matchmarks do not need to be placed if the glass is not going to be reused.

    5. Cut through the adhesive by pulling the piano wire around the back window glass.

      Note:

      Leave as much adhesive on the vehicle body as possible when removing the back window glass.

    6. Using suction cups, remove the back window glass.

      Note:

      If the stopper is damaged, the back window glass assembly must be replaced. Be careful when performing the procedure.

  51. Click here

    CLEAN BACK WINDOW GLASS


    1. Clean the outer edge of the back window glass with a non-residue solvent.

      Note:

      • Do not touch the back window glass surface after cleaning it.

      • Be careful not to damage the glass.

      • Even if using new back window glass, clean the back window glass with a non-residue solvent.

  52. Click here

    CLEAN VEHICLE BODY


    1. Using a scraper, remove the moulding and adhesive from the back window glass.

    2. Clean and shape the contact surface of the vehicle body.


      1. On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

        Tip:

        Leave as much adhesive on the vehicle body as possible.

        Note:

        Be careful not to damage the vehicle body.

      2. Clean the contact surface of the vehicle body with cleaner.

        Tip:

        Even if all the adhesive has been removed, clean the vehicle body.