Tech Tips
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)
REMOVE DECK BOARD ASSEMBLY (w/o Spare Tire)
REMOVE DECK TRIM SIDE BOARD LH (w/o Spare Tire)
Detach the 2 clips and remove the deck trim side board LH.
REMOVE BATTERY SERVICE HOLE COVER LH
*A | for Standard |
*B | for Ottoman |
*1 | Fastening Tape |
Detach the clip, fastening tape and remove the battery service hole cover LH.
PRECAUTION
Note
After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery negative (-) terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery negative (-) terminal notices before proceeding with work Click here.
DISCONNECT CABLE FROM AUXILIARY BATTERY NEGATIVE TERMINAL
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Note
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
REMOVE FRONT SEAT ASSEMBLY
REMOVE REAR SEAT ASSEMBLY (for Fixed Type)
REMOVE REAR SEAT ASSEMBLY (for Power Seat)
REMOVE REAR SEAT ASSEMBLY (for 4-Passenger with Ottoman)
REMOVE REAR SEAT ASSEMBLY (for 5-Passenger with Ottoman)
REMOVE FRONT DOOR SCUFF PLATE LH
Put protective tape around the front door scuff plate LH.
*1 | Protective Tape |
Using moulding remover D, detach the 4 clips.
Detach the 7 claws and remove the front door scuff plate LH.
REMOVE FRONT DOOR SCUFF PLATE RH
Tech Tips
Use the same procedure described for the LH side.
REMOVE COWL SIDE TRIM BOARD LH
Detach the 3 claws and remove the cowl side trim board LH.
REMOVE COWL SIDE TRIM BOARD RH
Tech Tips
Use the same procedure described for the LH side.
REMOVE FRONT PILLAR GARNISH LH
*1 | Front Pillar Garnish Clip |
Pull the upper part of the front pillar garnish LH toward the inside of the cabin and detach the 2 clips.
Tech Tips
Make the front pillar garnish LH hang down from the front pillar garnish clip.
*1 | Front Pillar Garnish Clip |
*2 | Protective Tape |
Turn the end of the front pillar garnish clip 90° with needle-nose pliers and remove it from the front pillar garnish LH.
Note
Front pillar garnish clips are reusable if they are not removed from the vehicle and have no damage.
Replace the front pillar garnish clips with new ones if they are removed from the vehicle.
Tech Tips
Tape the tips of the needle-nose pliers before use.
Pull the front pillar garnish LH to detach the guide and remove it.
*1 | Adhesive Tape |
*2 | Protective Cover |
Protect the curtain shield airbag assembly LH.
Completely cover the curtain shield airbag assembly LH with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.
Note
Cover the curtain shield airbag assembly LH with a protective cover as soon as the front pillar garnish LH is removed.
REMOVE FRONT PILLAR GARNISH RH
Tech Tips
Use the same procedure described for the LH side.
REMOVE REAR DOOR SCUFF PLATE LH
Put protective tape around the rear door scuff plate LH.
*1 | Protective Tape |
Using moulding remover D, detach the 4 clips.
Detach the 7 claws and remove the rear door scuff plate LH.
REMOVE REAR DOOR SCUFF PLATE RH
Tech Tips
Use the same procedure described for the LH side.
REMOVE CENTER LOWER PILLAR GARNISH LH
Detach the 2 claws and 6 clips, and remove the center lower pillar garnish LH.
REMOVE CENTER LOWER PILLAR GARNISH RH
Tech Tips
Use the same procedure described for the LH side.
REMOVE CENTER UPPER PILLAR GARNISH LH
Remove the 2 screws.
Detach the claw, guide and remove the center upper pillar garnish LH.
Pass the front seat outer belt floor anchor through the center upper pillar garnish LH.
REMOVE CENTER UPPER PILLAR GARNISH RH
Tech Tips
Use the same procedure described for the LH side.
REMOVE SHOULDER BELT ANCHOR COVER LH
Slide the shoulder belt anchor cover in the direction of the arrow to detach the 6 claws and remove it from the center upper pillar garnish LH.
REMOVE SHOULDER BELT ANCHOR COVER RH
Tech Tips
Use the same procedure described for the LH side.
REMOVE REAR SEAT SIDE GARNISH LH
Detach the 6 claws and remove the rear seat side garnish LH.
REMOVE REAR SEAT SIDE GARNISH RH
Tech Tips
Use the same procedure described for the LH side.
REMOVE INNER ROOF SIDE GARNISH LH
*1 | Clip A |
Pull the inner roof side garnish LH away from the body and detach the 4 clips (do not detach clip A).
Detach the 2 claws of the guide, and pull the inner roof side garnish LH in the direction of the arrow to remove it.
Tech Tips
Clip A remains attached to the body.
Remove clip A from the vehicle body.
REMOVE INNER ROOF SIDE GARNISH RH
Tech Tips
Use the same procedure described for the LH side.
REMOVE MAP LIGHT ASSEMBLY
Using a screwdriver, detach the 2 claws and open the 2 covers.
Tech Tips
Tape the screwdriver tip before use.
Remove the 2 screws.
Using moulding remover D, detach the 2 clips and remove the map light assembly.
Disconnect the 2 connectors.
*1 | Protective Tape | - | - |
REMOVE SPOT LIGHT LENS (w/ Rear Seat Entertainment System)
Detach the 4 claws and remove the spot light lens.
REMOVE ROOF CONSOLE BOX ASSEMBLY (w/ Rear Seat Entertainment System)
Remove the 2 screws.
Detach the 6 clips and 2 claws and remove the roof console box assembly.
w/o Infrared Ray Sensor:
Disconnect the connector.
w/ Infrared Ray Sensor:
Disconnect the 2 connectors.
REMOVE SPOT LIGHT LENS (for 5-Passenger with Ottoman)
*1 | Protective Tape |
Using a screwdriver, detach the 4 claws and remove the spot light lens.
Tech Tips
Tape the screwdriver tip before use.
REMOVE ROOF CONSOLE BOX ASSEMBLY (for 5-Passenger with Ottoman)
Remove the 2 screws.
Detach the 2 claws, 2 clips and 2 hooks and remove the roof console box assembly.
Disconnect the 2 connectors.
REMOVE SPOT LIGHT ASSEMBLY (w/o Rear Seat Entertainment System)
Using moulding remover D, detach the 4 claws and remove the spot light assembly.
Disconnect the connector.
REMOVE REAR VANITY LIGHT ASSEMBLY
Tech Tips
Use the same procedure to remove the vanity light assembly on the other side.
Using a screwdriver, detach the 4 claws and remove the lens.
Tech Tips
Tape the screwdriver tip before use.
Remove the 2 screws.
Using moulding remover D, detach the claw and remove the vanity light assembly.
Disconnect the connector.
*1 | Protective Tape | - | - |
REMOVE ROOF SIDE REGISTER BEZEL LH
Remove the screw.
Detach the claw and remove the roof side register bezel LH.
REMOVE ROOF SIDE REGISTER BEZEL RH
Tech Tips
Use the same procedure described for the LH side.
REMOVE ASSIST GRIP SUB-ASSEMBLY
*1 | Protective Tape |
Tech Tips
Use the same procedure for all the assist grips.
Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.
Tech Tips
Tape the screwdriver tip before use.
Detach the 2 clips and remove the assist grip sub-assembly.
REMOVE VISOR BRACKET COVER
Tech Tips
Use the same procedure to remove the visor bracket cover on the other side.
Using moulding remover D, detach the 4 claws and remove the visor bracket cover.
REMOVE VISOR ASSEMBLY LH
Remove the 2 screws and visor assembly LH.
REMOVE VISOR ASSEMBLY RH
Tech Tips
Use the same procedure described for the LH side.
REMOVE VISOR HOLDER
Tech Tips
Use the same procedure to remove the visor holder on the other side.
Turn the visor holder approximately 45° and pull it out as shown in the illustration.
Detach the 2 claws and remove the visor holder.
*a | 45° | - | - |
REMOVE RAIN SENSOR COVER
w/o Lane Keeping Assist System:
w/ Lane Keeping Assist System:
REMOVE INNER REAR VIEW MIRROR ASSEMBLY
w/o Automatic High Beam System:
w/ Automatic High Beam System:
REMOVE OBJECT RECOGNITION CAMERA (w/ Lane Keeping Assist System)
Partially remove the roof headlining assembly.
Tech Tips
It is not necessary to completely remove the roof headlining. Slightly lower the front section of the roof headlining so that the object recognition camera can be removed.
Disconnect the 3 connectors.
Detach the 2 wire harness clamps.
Detach the claw and disconnect the connector clamp.
Remove the 3 bolts.
Detach the clip and remove the object recognition camera.
*A | w/o Night View System | *B | w/ Night View System |
REMOVE WINDSHIELD GLASS
REMOVE ROOF HEADLINING ASSEMBLY
Disconnect the roof wire connectors and detach each wire harness clamp from the front pillar LH.
*A | w/ Lane Keeping Assist System |
Disconnect each connector and each wire harness clamp.
w/o Rear Seat Entertainment System:
Detach the hook, 12 claws, 10 fasteners and 4 clips.
w/ Rear Seat Entertainment System:
Detach the hook, 12 claws, 8 fasteners and 4 clips.
Remove the roof headlining assembly through the front of the vehicle.
Note
Be careful not to damage the roof headlining assembly when taking it out.
REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Remove the front door opening trim weatherstrip LH.
REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Tech Tips
Use the same procedure described for the LH side.
REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
Remove the rear door opening trim weatherstrip.
REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
Tech Tips
Use the same procedure described for the LH side.