PARKING BRAKE LEVER INSTALLATION

Tech Tips

Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.

INSTALL PARKING BRAKE SWITCH ASSEMBLY
1. Connect the connector to the parking brake switch.
2. Install the parking brake switch to the parking brake lever with the screw.
  
  Torque:
  
  0.9 N*m { 9 kgf*cm, 8 in.*lbf }
INSTALL PARKING BRAKE LEVER SUB-ASSEMBLY
1. Install the parking brake lever with the 2 bolts.
  
  Torque:
  
  13 N*m { 127 kgf*cm, 9 ft.*lbf }
2. Install the parking brake lever support with the 2 bolts.
  
  Torque:
  
  13 N*m { 127 kgf*cm, 9 ft.*lbf }
3. Install the straight pin to the parking brake lever.
4. Connect the No. 2 parking brake cable and No. 3 parking brake cable to the No. 1 parking brake pull rod.
5. Install the bush, compression spring and No. 1 parking brake pull rod to the parking brake lever with the adjusting nut.
6. Install the parking brake return spring.
7. Connect the parking brake switch connector.
INSPECT PARKING BRAKE LEVER TRAVEL
1. Fully pull the parking brake lever to engage the parking brake.
2. Release the lever to disengage the parking brake.
3. Slowly pull the parking brake lever all the way and count the number of clicks.
  
  Standard parking brake lever travel when pulled with a force of 200 N (20 kgf, 45 lbf)
  
  5 to 7 clicks
  
  If the parking brake lever travel is not as specified, adjust the parking brake shoe clearance and parking brake lever travel.

ADJUST PARKING BRAKE LEVER TRAVEL

for Automatic Transmission:

Remove the rear console box assembly Click here.
for Manual Transmission:

Remove the rear console box assembly Click here.
w/ Refrigerated Cool Box:

Remove the rear console box assembly Click here.
for Bench Seat Type:

Remove the rear console box assembly Click here.
Completely release the parking brake lever.
Loosen the adjusting nut to completely release the parking brake cable.
Temporarily install the hub nuts.

A01DOW0E08

Turn the shoe adjuster so that it expands until the disc locks.

Text in Illustration
	Shoe Adjuster Contracts
	Shoe Adjuster Expands

Turn the shoe adjuster so that it contracts until the disc can rotate smoothly.

OK

8 notches
Check that there is no brake drag against the shoe.
Install the hole plug.
Remove the hub nuts.
Turn the adjusting nut until the parking brake lever travel becomes correct.

Standard parking brake lever travel when pulled with a force of 200 N (20 kgf, 45 lbf)

5 to 7 clicks
Operate the parking brake lever 3 to 4 times and check the parking brake lever travel.

Standard parking brake lever travel when pulled with a force of 200 N (20 kgf, 45 lbf)

5 to 7 clicks
Check whether the parking brake drags or not.
When operating the parking brake lever, check that the brake warning light comes on.

Standard

The brake warning light always illuminates at the first click.
for Automatic Transmission:

Install the rear console box assembly Click here.
for Manual Transmission:

Install the rear console box assembly Click here.
w/ Refrigerated Cool Box:

Install the rear console box assembly Click here.
for Bench Seat Type:

Install the rear console box assembly Click here.

INSTALL REAR CONSOLE BOX ASSEMBLY
1. for Automatic Transmission:
  
  Install the rear console box assembly Click here.
2. for Manual Transmission:
  
  Install the rear console box assembly Click here.
3. w/ Refrigerated Cool Box:
  
  Install the rear console box assembly Click here.
4. for Bench Seat Type:
  
  Install the rear console box assembly Click here.