Click here

VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster), Diagnostic DTC:C1232, C1243, C1245, C1279

Click here
Click here Click here
DTC Code DTC Name
C1232 Acceleration Sensor Stuck Malfunction
C1243 Acceleration Sensor Stuck Malfunction
C1245 Acceleration Sensor Output Malfunction
C1279 Acceleration Sensor Output Voltage Malfunction (Test Mode DTC)
Click here

DESCRIPTION

The skid control ECU receives signals from the yaw rate and acceleration sensor via the CAN communication system.

If there is trouble in the bus lines between the yaw rate and acceleration sensor and the CAN communication system, DTCs U0123 (yaw rate sensor communication trouble) and U0124 (acceleration sensor communication trouble) are stored.

DTC Code DTC Detection Condition Trouble Area
C1232 At a vehicle speed of 10 km/h (6 mph) or more, the fluctuation range of the signal from one of either GL1 or GL2 is below 80 mV and the fluctuation range of the signal of the other is higher than 1.9 V for 30 seconds or more.

  • ECU-IG NO. 1 fuse

  • Sensor installation

  • Harness or connector

  • Yaw rate and acceleration sensor

  • CAN communication system
C1243

The following condition repeats 16 times.


  • GL1 and GL2 do not change when the vehicle decelerates from 30 km/h (19 mph) to 0 km/h (0 mph).
C1245

The following condition continues for at least 60 seconds.


  • The difference between the values calculated from the acceleration sensor value and vehicle speed exceeds 0.35 G.
C1279 Stored during test mode.
Click here

WIRING DIAGRAM

Click here

INSPECTION PROCEDURE

Note:

  • When replacing the yaw rate and acceleration sensor, perform calibration (Click here).

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

Click here

PROCEDURE


  1. Click here

    CHECK FOR DTC


    1. Clear the DTCs (Click here).

    2. Turn the ignition switch off.

    3. Turn the ignition switch to ON.

    4. Check if DTCs U0073, U0123, C1210 and/or C1336 are output (Click here).

      Table 1. Result
      Result Proceed to
      DTC U0073, U0123, C1210 and/or C1336 are not output A
      DTC U0073 and/or U0123 are output (for LHD) B
      DTC U0073 and/or U0123 are output (for RHD) C
      DTC C1210 and/or C1336 are output D

  2. Click here

    CHECK YAW RATE AND ACCELERATION SENSOR INSTALLATION


    1. Check that the yaw rate and acceleration sensor is installed properly.

      OK
      The sensor is tightened to the specified torque. The sensor is not tilted.

  3. Click here

    CHECK TERMINAL VOLTAGE AND RESISTANCE (IG, GND)


    1. Disconnect the G52 yaw rate and acceleration sensor connector.

    2. A01DTX5E05

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      G52-4 (IG) - Body ground Ignition switch ON 11 to 14 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G52-1 (GND) - Body ground Always Below 1 Ω
      Table 2. Text in Illustration
      *a

      Front view of wire harness connector

      (to Yaw Rate and Acceleration Sensor)
      Table 3. Result
      Result Proceed to
      OK (When troubleshooting in accordance with Diagnostic Trouble Code Chart) A
      OK (When troubleshooting in accordance with Problem Symptoms Table) B
      NG C

  4. Click here

    REPLACE YAW RATE AND ACCELERATION SENSORClick here

  5. Click here

    GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)Click here

  6. Click here

    REPAIR CIRCUIT INDICATED BY OUTPUT DTCClick here

  7. Click here

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLEClick here

  8. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  9. Click here

    INSTALL YAW RATE AND ACCELERATION SENSOR CORRECTLYClick here

  10. Click here

    GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)Click here