REAR VIEW MONITOR SYSTEM (for Radio and Display Type) Image from Camera for Rear View Monitor is Abnormal

DESCRIPTION

This is the display signal circuit between the radio and display receiver assembly and the rear television camera assembly.

WIRING DIAGRAM

A01DUM3E04

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)


    1. Disconnect the H50 radio and display receiver assembly connector.

    2. Disconnect the X9*1 or v2*2 rear television camera assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      w/ Tire Carrier
      Tester Connection Condition Specified Condition
      H50-11 (CA+) - X9-6 (CB+) Always Below 1 Ω
      H50-12 (V+) - X9-3 (CV+) Always Below 1 Ω
      H50-23 (CGND) - X9-5 (CGND) Always Below 1 Ω
      H50-24 (V-) - X9-2 (CV-) Always Below 1 Ω
      H50-11 (CA+) - Body ground Always 10 kΩ or higher
      H50-12 (V+) - Body ground Always 10 kΩ or higher
      H50-23 (CGND) - Body ground Always 10 kΩ or higher
      H50-24 (V-) - Body ground Always 10 kΩ or higher
      w/o Tire Carrier
      Tester Connection Condition Specified Condition
      H50-11 (CA+) - v2-6 (CB+) Always Below 1 Ω
      H50-12 (V+) - v2-3 (CV+) Always Below 1 Ω
      H50-23 (CGND) - v2-5 (CGND) Always Below 1 Ω
      H50-24 (V-) - v2-2 (CV-) Always Below 1 Ω
      H50-11 (CA+) - Body ground Always 10 kΩ or higher
      H50-12 (V+) - Body ground Always 10 kΩ or higher
      H50-23 (CGND) - Body ground Always 10 kΩ or higher
      H50-24 (V-) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY


    1. A01DM1GE07
      Text in Illustration
      *a

      Component with harness connected

      (Radio and Display Receiver Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H50-23 (CGND) - Body ground Always Below 1 Ω
      H50-24 (V-) - Body ground Always Below 1 Ω

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      H50-11 (CA+) - Body ground Ignition switch ON 5.5 to 7.05 V
      Result
      Result Proceed to
      OK A
      NG (w/ Navigation System) B
      NG (w/o Navigation System) C

    B

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY Click here

    C

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY Click here

    A

  3. CHECK REAR TELEVISION CAMERA ASSEMBLY


    1. Using an oscilloscope, check the waveform.

      A01DONHE13
      Text in Illustration
      *a

      Component with harness connected

      (Radio and Display Receiver Assembly)

      		 *b Waveform 1
      *c Waveform 2 *d Synchronized Signal
      *e Video Waveform - -
      Measurement Condition
      Item Content
      Tester Connection H50-12 (V+) - H50-23 (CGND)
      Tool Setting 200 mV/DIV., 50 μs/DIV.
      Condition

      • Waveform 1: Ignition switch ON, camera lens not covered, displaying an image

      • Waveform 2: Ignition switch ON, camera lens covered, blacking out screen
      OK
      Waveform is as shown in illustration.

      Tech Tips

      The video waveform changes according to the image sent by the rear television camera assembly.

      Result
      Result Proceed to
      OK A
      NG (w/ Tire Carrier) B
      NG (w/o Tire Carrier) C

    B

    REPLACE REAR TELEVISION CAMERA ASSEMBLY Click here

    C

    REPLACE REAR TELEVISION CAMERA ASSEMBLY Click here

    A

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here