BLACK OUT TAPE (for Front Door) REMOVAL


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY

    Click here

  4. REMOVE DOOR SIDE AIRBAG SENSOR


    1. Check that the ignition switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Disconnect the connector from the door side airbag sensor.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.


      1. Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

        A01HN61E12
        Text in Illustration
        *1 White Housing Lock *2 Yellow CPA
        *a Connector Lock is Released - -

      2. Push down the white housing lock again and disconnect the connector.

        Note

        Do not push down the part (A) shown in the illustration when disconnecting.

    4. A01HR0Q

      Remove the bolt and door side airbag sensor from the front door panel.

      Note

      Loosen the bolt while holding the door side airbag sensor because the door side airbag sensor pin (stopper) is easily damaged.

    5. After disconnecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

      A01HQ1GE01
      Text in Illustration
      *a Incorrect *b Correct

  5. REMOVE FRONT DOOR SERVICE HOLE COVER


    1. A01HMZD

      Remove the bolt.

    2. Disconnect each connector.

    3. Disengage the 5 clamps.

    4. Remove the front door service hole cover.

      Tech Tips

      Remove any remaining butyl tape from the door.

  6. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY


    1. A01HP1Z

      Remove the grommet.

    2. Connect the cable to the negative (-) battery terminal.

    3. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

    4. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    5. Disconnect the power window regulator master switch assembly.

    6. A01HN2F

      Remove the 2 bolts.

      Note

      After the bolts are removed, do not allow the door glass to fall.

    7. A01HOINE01

      Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.

      Note

      Do not damage the door glass.

  7. REMOVE FRONT DOOR GLASS RUN


    1. A01HPZ2

      Remove the front door glass run.

  8. REMOVE FRONT DOOR CHECK ASSEMBLY


    1. A01HNGK

      Remove the 3 bolts and front door check assembly.

  9. REMOVE FRONT DOOR WEATHERSTRIP


    1. A01HP9A

      Using a clip remover, disengage the 19 clips and remove the front door weatherstrip.

  10. REMOVE DOOR FRAME GARNISH


    1. A01HQL1

      Disengage the clip and remove the door frame garnish.

      Tech Tips

      This garnish needs to be replaced with a new one because the clip will break when removing it.

  11. REMOVE FRONT DOOR STRIPE


    1. Using a heat light, heat the front door stripe and vehicle body.

      Heating Temperature
      Item Temperature
      Vehicle Body and Front Door Outside Stripe 40 to 60°C (104 to 140°F)

      Note

      Do not heat the vehicle body excessively.

    2. A01HQMF

      Pull back on one of the ends of the front door stripe to remove it.

      Tech Tips

      When pulling on the stripe, pull it parallel to the body.

  12. REMOVE FRONT DOOR LOWER OUTSIDE STRIPE


    1. Using a heat light, heat the front door lower outside stripe and vehicle body.

      Heating Temperature
      Item Temperature
      Vehicle Body and Front Door Rear Outside Stripe 40 to 60°C (104 to 140°F)

      Note

      Do not heat the vehicle body excessively.

    2. A01HNN7

      Pull back on one of the ends of the front door lower outside stripe to remove it.

      Tech Tips

      When pulling on the stripe, pull it parallel to the body.