LUGGAGE DOOR LOCK CONTROL CABLE ASSEMBLY REMOVAL


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE FRONT SEAT ASSEMBLY LH (for TMMK Made Manual Seat)

    Click here

  4. REMOVE FRONT SEAT ASSEMBLY LH (for TMMK Made Power Seat)

    Click here

  5. REMOVE FRONT SEAT ASSEMBLY LH (for SIA Made Manual Seat)

    Click here

  6. REMOVE FRONT SEAT ASSEMBLY LH (for SIA Made Power Seat)

    Click here

  7. REMOVE REAR SEAT CUSHION ASSEMBLY


    1. Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.

      Note

      Follow the instructions below carefully as the cushion frame can be deformed easily.


      1. A01HQ78E01

        Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.

        Standard Measurement
        a 100 mm (3.94 in.) or less

      2. Repeat the step above for the other hook.

    2. Remove the rear seat cushion assembly.

  8. REMOVE REAR SEAT CUSHION LOCK HOOK


    1. A01HNQ7

      Disengage the claw and remove the rear seat cushion lock hook.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure for the RH side and the LH side.

  9. REMOVE REAR SIDE SEATBACK ASSEMBLY LH


    1. Disconnect the rear seat outer belt from the rear seat shoulder belt guide.

    2. Disconnect the connector.

    3. A01HOY2

      Remove the 2 bolts.

    4. Disengage the hook and remove the rear side seatback assembly LH.

  10. REMOVE FRONT DOOR SCUFF PLATE LH


    1. A01HNV0

      Disengage the 10 claws and remove the front door scuff plate LH.

  11. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. Disconnect the front door opening trim weatherstrip.

  12. REMOVE REAR DOOR SCUFF PLATE LH


    1. A01HMI8

      Disengage the 6 claws and remove the rear door scuff plate LH.

      Tech Tips

      Disengage the claws from the rear side of the scuff plate.

  13. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. Disconnect the rear door opening trim weatherstrip.

  14. REMOVE LAP BELT OUTER ANCHOR COVER


    1. A01HOL8

      Disengage the 3 claws and remove the lap belt outer anchor cover.

  15. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    1. A01HMIZ

      Remove the bolt and disconnect the floor anchor of the front seat outer belt assembly.

  16. REMOVE CENTER PILLAR LOWER GARNISH LH


    1. A01HQGX

      Disengage the 2 claws and 3 clips, and remove the center pillar lower garnish LH.

  17. REMOVE LUGGAGE COMPARTMENT DOOR COVER


    1. A01HND7

      Remove the 13 clips and luggage compartment door cover.

  18. REMOVE SPARE WHEEL COVER ASSEMBLY


    1. Remove the spare wheel cover assembly.

  19. REMOVE REAR FLOOR FINISH PLATE


    1. A01HQ5Y

      Remove the 5 clips.

    2. A01HNUP

      Disengage the 4 clips and remove the rear floor finish plate.

  20. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK


    1. A01HMF6E01
      Text in Illustration
      *1 Pin

      Push the pin and remove the No. 1 luggage compartment trim hook.

  21. REMOVE LUGGAGE COMPARTMENT INNER TRIM COVER LH


    1. A01HPY3E01
      Text in Illustration
      *1 Clip <A>
      *2 Clip <B>

      Remove the clip <A>.

    2. Remove the 2 clips <B>.

    3. A01HR0W

      Disengage the fastener and remove the luggage compartment inner trim cover LH.

  22. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY


    1. A01HQUE

      Remove the screw.

    2. A01HQY3

      Disengage the guide and disconnect the fuel lid lock open lever sub-assembly as shown in the illustration.

    3. A01HO1J

      Disconnect the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly and remove the fuel lid lock open lever sub-assembly.

  23. REMOVE LUGGAGE DOOR LOCK CONTROL CABLE SUB-ASSEMBLY


    1. A01HN8U

      Disengage the 2 clamps.

    2. A01HPK1

      Using a clip remover, disengage the clamp and disconnect the wire harness.

    3. A01HPLT

      Using a clip remover, disengage the 2 clamps and remove the 2 scuff plate clips.

    4. Turn back the floor carpet so that the luggage door lock control cable sub-assembly and fuel lid lock control cable sub-assembly can be removed.

    5. w/o Wireless Door Lock Control System:


      1. A01HQ3O

        Disconnect the luggage door lock control cable sub-assembly.

      2. A01HMB3

        Disengage the 3 clamps and disconnect luggage door lock control cable sub-assembly.

    6. w/ Wireless Door Lock Control System:


      1. A01HMEY

        Disengage the guide as shown in the illustration.

      2. A01HPOT

        Disconnect the luggage door lock control cable sub-assembly.

      3. A01HMJD

        Disengage the clamp and disconnect the luggage door lock control cable sub-assembly.

    7. A01HQJUE01
      Text in Illustration
      *1 Cutout
      *2 Guide <A>

      Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and the guides <A>, and then pull the fuel filler opening lid lock retainer.

    8. A01HQOFE01
      Text in Illustration
      *1 Cutout
      *2 Guide <B>

      Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and guides <B>, and then pull the fuel filler opening lid lock retainer.

    9. A01HMKKE01
      Text in Illustration
      *1 Cutout
      *2 Guide <C>
      *3 Guide <B>

      Pull out the fuel filler opening lid lock retainer with both guides <B and C> aligned with the cutouts.

    10. A01HQKY

      Disengage the 2 claws and remove the fuel filler opening lid lock retainer.

    11. Disengage the 10 clamps and remove the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly.

      A01HNPYE01
      Text in Illustration
      *1 Fuel Lid Lock Control Cable Sub-assembly *2 Luggage Door Lock Control Cable Sub-assembly

    12. Using a knife, cut off the clamp as shown in the illustration.

      A01HQ96E01
      Text in Illustration
      *1 Tape - -
      *a Cut - -

      Note

      Be careful not to damage the vehicle fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly.

    13. Remove the clamp.

    14. Remove the 3 pieces of tape and fuel lid lock control cable sub-assembly.