NOISE FILTER REMOVAL


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE REAR SEAT CUSHION ASSEMBLY


    1. Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.

      Note

      Follow the instructions below carefully as the cushion frame can be deformed easily.


      1. A01HQ78E01

        Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.

        Standard Measurement
        a 100 mm (3.94 in.) or less

      2. Repeat the step above for the other hook.

    2. Remove the rear seat cushion assembly.

  4. REMOVE REAR SEAT CUSHION LOCK HOOK


    1. A01HNQ7

      Disengage the claw and remove the rear seat cushion lock hook.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure for the RH side and the LH side.

  5. REMOVE REAR SIDE SEATBACK ASSEMBLY LH


    1. Disconnect the rear seat outer belt from the rear seat shoulder belt guide.

    2. Disconnect the connector.

    3. A01HOY2

      Remove the 2 bolts.

    4. Disengage the hook and remove the rear side seatback assembly LH.

  6. REMOVE RADIO SETTING CONDENSER (for High Mounted Stop Light)

    Note

    When the terminal covers are removed, the radio setting condenser must be replaced because the terminal covers and condenser are supplied as a set.


    1. A01HPM3

      Remove the bolt.

    2. Disengage the clamp and disconnect the radio setting condenser with wire harness from the vehicle body.

    3. A01HMN7

      Disengage the claw and pull out the cover as shown in the illustration.

    4. A01HQNA

      Using a screwdriver, disengage the 6 claws and remove the 2 terminal covers with wire harness from the condenser.

    5. A01HQ40

      Using a screwdriver, bend back and break off the claw as shown in the illustration.

    6. Remove the terminal cover from the wire harness.

      Note


      • Make sure to hold the wire harness on the crimping side of the terminal when disconnecting the wire harness from the terminal cover.

      • Make sure not to bend the exposed wire when disconnecting the wire harness from the terminal cover.

      • Check for deformation of the terminal after the wire harness has been removed from the terminal cover.

  7. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Window Defogger)


    1. Disconnect the rear door opening trim weatherstrip LH.

  8. REMOVE ROOF SIDE INNER GARNISH LH (for Window Defogger)


    1. A01HQV9

      Disengage the 5 clips.

    2. Disengage the guide and remove the roof side inner garnish LH.

  9. REMOVE RADIO SETTING CONDENSER (for Window Defogger)

    Note

    When the terminal cover is removed, the radio setting condenser must be replaced because the terminal cover and condenser are supplied as a set.


    1. A01HMSV

      Remove the bolt.

    2. Disengage the 2 clamps and disconnect the radio setting condenser with wire harness from the vehicle body.

    3. A01HNMV

      Using a screwdriver, disengage the 3 claws and remove the terminal cover with wire harness from the condenser.

    4. A01HNNM

      Using a screwdriver, bend back and break off the claw as shown in the illustration.

    5. Remove the terminal cover from the wire harness.

      Note


      • Make sure to hold the wire harness on the crimping side of the terminal when disconnecting the wire harness from the terminal cover.

      • Make sure not to bend the exposed wire when disconnecting the wire harness from the terminal cover.

      • Check for deformation of the terminal after the wire harness has been removed from the terminal cover.