ELECTRICAL KEY OSCILLATOR (for Front Door) INSTALLATION


  1. INSTALL DOOR ELECTRICAL KEY OSCILLATOR


    1. A015Z3B

      Install the door electrical key oscillator with the screw.

  2. INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY


    1. Apply MP grease to the sliding parts on the front door outside handle frame sub-assembly.

    2. A0162TA

      Install the front door outside handle frame sub-assembly with the claws.

    3. Using a "TORX" socket wrench (T30), install the front door outside handle frame sub-assembly with the screw.

      Torque:
      4.0 N*m  { 41 kgf*cm, 35 in.*lbf }

    4. Engage the 2 clamps.

    5. Connect the connector.

  3. INSTALL FRONT DOOR LOCK ASSEMBLY

    Note


    • When reusing the removed front door lock assembly, replace the door lock wire harness seal on the connector with a new one.

    • Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.

    • Reusing the door lock wiring harness seal and/or using damaged door lock wiring harness seal may cause water intrusion. This may result in a malfunction in the front door lock assembly.


    1. Apply MP grease to the sliding parts of the front door lock assembly.

    2. Install a new door lock wiring harness seal to the front door lock assembly.

    3. A0161ZL

      Insert the front door lock open rod to the front door lock assembly, and set it to the front door outside handle frame.

    4. Make sure that the front door lock open rod is securely connected to the front door lock assembly.

    5. Using a "TORX" socket wrench (T30), install the front door lock assembly with the 3 screws.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

  4. INSTALL FRONT DOOR REAR OUTSIDE HANDLE PAD


    1. A0163HC

      Engage the 2 claws to install the front door rear outside handle pad.

  5. INSTALL FRONT DOOR FRONT OUTSIDE HANDLE PAD


    1. A015Z6S

      Engage the 3 claws to install the front door front outside handle pad.

  6. INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY


    1. A0161HL

      Insert the front end of the front door outside handle assembly into the front door outside handle frame.

    2. Insert the rear end of the front door outside handle assembly into the front door outside handle frame then slide the front door outside handle assembly to the front of the vehicle to install it.

    3. A015YKP

      Using a "TORX" socket wrench (T30), install the front door outside handle assembly with the screw.

      Torque:
      4.0 N*m  { 41 kgf*cm, 35 in.*lbf }

    4. Connect the connector.

  7. INSTALL FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)


    1. A01629Y

      Install the front door lock cylinder assembly.

      Tech Tips

      Make sure that the front door lock cylinder rod is inserted into the front door lock assembly.

    2. A016229

      Using a "TORX" socket wrench (T30), install the front door lock cylinder assembly with the screw.

      Torque:
      4.0 N*m  { 41 kgf*cm, 35 in.*lbf }

    3. Install the hole plug.

  8. INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)


    1. A0161Z6

      Engage the 2 claws of the front door outside handle cover.

  9. INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)


    1. A0163AF

      Using a "TORX" socket wrench (T30), install the front door outside handle cover with the screw.

      Torque:
      4.0 N*m  { 41 kgf*cm, 35 in.*lbf }

    2. Install the hole plug.

  10. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY


    1. A0161PP

      Install the front door rear lower frame sub-assembly with the bolt.

  11. INSTALL FRONT DOOR SERVICE HOLE COVER


    1. Apply butyl tape to the front door panel.

    2. Pass the front door lock remote control cable and front door inside locking cable through a new front door service hole cover.

    3. A015ZN9E01

      Attach the front door service hole cover according to the reference points on the front door panel.

      Note

      Securely install the front door service hole cover preventing wrinkles and air bubbles.

    4. Engage each clamp.

    5. Connect each connector.

  12. INSTALL FRONT DOOR TRIM COVER


    1. A016263

      Engage the 6 clips to install the front door trim cover.

    2. Install the screw.

  13. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP


    1. A0161HF

      Engage the 4 claws and install the front door inner glass weatherstrip.

  14. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    1. Install 2 new front door trim board retainers (green).

    2. A01630D

      Connect the front door lock remote control cable and front door inside locking cable to the front inside handle.

    3. Connect each connector.

    4. A01614A

      Engage the front door trim board with the 4 clips of the front door inner glass weatherstrip.

    5. A0160MG

      Engage the 9 clips and install the front door trim board to the front door panel.

    6. Install the 2 screws.

  15. INSTALL COURTESY LIGHT ASSEMBLY


    1. Connect the connector.

    2. A0160WE

      Engage the claw and install the courtesy light assembly.

  16. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    1. Connect each connector.

    2. A015YVS

      Engage the 3 claws and 2 clips, and install the power window regulator master switch assembly with front door armrest base panel.

  17. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    1. Connect the connector.

    2. A0160OD

      Engage the 3 claws and 2 clips and install the power window regulator switch assembly with front door armrest base panel.

  18. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG


    1. A01613G

      Engage the 3 claws and install the front door inside handle bezel plug.

  19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  20. INITIALIZE POWER WINDOW CONTROL SYSTEM

    Click here