TILT AND TELESCOPIC MANUAL SWITCH INSTALLATION


  1. INSTALL TILT AND TELESCOPIC SWITCH


    1. A0163FB

      Engage the claw to install the tilt and telescopic switch.

    2. Connect the connector.

  2. INSTALL LOWER STEERING COLUMN COVER


    1. A0161BR

      Engage the 2 claws to install the lower steering column cover.

      Note

      Do not damage the tilt and telescopic switch.

    2. Install the 3 screws.

      Torque:
      2.0 N*m  { 20 kgf*cm, 18 in.*lbf }

  3. ADJUST SPIRAL CABLE SUB-ASSEMBLY


    1. Check that the engine switch is off.

    2. Check that the battery negative (-) cable is disconnected.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01602L

      Rotate the spiral cable counterclockwise slowly by hand until it stops.

      Note

      Do not turn the spiral cable using the airbag wire harness.

    4. A015YXZE04

      Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.

      Note

      Do not turn the spiral cable using the airbag wire harness.

      Tech Tips

      The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.

  4. INSTALL STEERING WHEEL ASSEMBLY


    1. A015YNDE01

      Align the matchmarks on the steering wheel assembly and steering main shaft.

    2. Install the steering wheel assembly set nut.

      Torque:
      50 N*m  { 510 kgf*cm, 37 ft.*lbf }

    3. Connect the connectors to the spiral cable sub-assembly.

  5. INSPECT STEERING WHEEL CENTER POINT

  6. INSTALL STEERING PAD


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A0161J5

      Connect the 2 airbag connectors to the steering pad.

      Note

      When connecting the airbag connector, take care not to damage the airbag wire harness.

    4. Connect the horn connector to the steering pad.

    5. Confirm that the circumference groove of the "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.

    6. A01600XE01

      Using a "TORX" socket wrench (T30), tighten the 2 "TORX" screws.

      Torque:
      8.8 N*m  { 90 kgf*cm, 78 in.*lbf }

  7. INSTALL LOWER NO. 3 STEERING WHEEL COVER


    1. A015ZUQ

      Install the lower No. 3 steering wheel cover with the claw.

  8. INSTALL LOWER NO. 2 STEERING WHEEL COVER


    1. A0160QU

      Install the lower No. 2 steering wheel cover with the claw.

  9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note


    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    • Reset the auto tilt away function setting to the previous condition by changing the customize parameter Click here.

  10. INSPECT STEERING PAD


    1. A016181

      With the steering pad installed on the vehicle, perform a visual check. If there are any following defects, replace the steering pad with a new one:


      • Cuts, minute cracks or marked discoloration on the steering pad top surface or grooves.

    2. Make sure that the horn sounds.

      Tech Tips

      If the horn does not sound, inspect the horn system Click here.

  11. INSPECT SRS WARNING LIGHT

    Click here.