PARKING BRAKE PEDAL REMOVAL


  1. REMOVE FRONT SEAT HEADREST ASSEMBLY

  2. REMOVE FRONT OUTER SEAT TRACK BRACKET COVER LH (for LHD)


    1. Operate the power seat switch knob and move the seat to the rearmost position.

    2. A0163FR

      Disengage the 2 claws and remove the front outer seat track bracket cover.

  3. REMOVE FRONT INNER SEAT TRACK BRACKET COVER LH (for LHD)


    1. A015Z4U

      Disengage the 2 claws and remove the front inner seat track bracket cover.

  4. REMOVE REAR OUTER SEAT TRACK BRACKET COVER LH (for LHD)


    1. Operate the power seat switch knob and move the seat to the foremost position.

    2. A0160NB

      Disengage the 2 claws and remove the rear outer seat track bracket cover.

  5. REMOVE REAR INNER SEAT TRACK BRACKET COVER LH (for LHD)


    1. A015ZKS

      Disengage the 2 claws and remove the rear inner seat track bracket cover.

  6. REMOVE FRONT SEAT ASSEMBLY LH (for LHD)


    1. Operate the power seat switch knob and move the seat to the foremost position.

    2. A0162WM

      Remove the 2 bolts on the rear side of the seat.

    3. Operate the power seat switch knob and move the seat to the rearmost position.

    4. A0161EE

      Remove the 2 bolts on the front side of the seat.

    5. Operate the power seat switch knob and move the seat to the center position. Also, operate the power seat switch knob and move the seatback to the upright position.

    6. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system Click here.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    7. Disconnect the connectors under the seat.

    8. Remove the front seat assembly.

      Note

      Be careful not to damage the vehicle body.

  7. REMOVE FRONT OUTER SEAT TRACK BRACKET COVER RH (for RHD)

    Tech Tips

    Use the same procedure for the RH side and LH side.

  8. REMOVE FRONT INNER SEAT TRACK BRACKET COVER RH (for RHD)

    Tech Tips

    Use the same procedure for the RH side and LH side.

  9. REMOVE REAR OUTER SEAT TRACK BRACKET COVER RH (for RHD)

    Tech Tips

    Use the same procedure for the RH side and LH side.

  10. REMOVE REAR INNER SEAT TRACK BRACKET COVER RH (for RHD)

    Tech Tips

    Use the same procedure for the RH side and LH side.

  11. REMOVE FRONT SEAT ASSEMBLY RH (for RHD)

    Tech Tips

    Use the same procedure for the RH side and LH side.

  12. REMOVE REAR SEAT CUSHION ASSEMBLY


    1. A0160U2E01

      Disengage the 2 front hooks of the rear seat cushion assembly from the vehicle body.

      Note

      Follow the instructions below carefully as the cushion frame deforms easily.


      1. Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.

      2. Repeat for the other hook.

    2. Disengage the 2 rear hooks of the seat cushion from the child restraint seat anchor bracket.

    3. Remove the rear seat cushion assembly.

  13. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    1. A0161TD

      Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.

  14. REMOVE UPPER NO. 1 CONSOLE PANEL GARNISH


    1. A0162WJ

      Using a moulding remover, disengage the claw.

    2. A0160YI

      Pull the upper No. 1 console panel garnish in the direction indicated by the arrow to disengage the 2 clips and remove the upper No. 1 console panel garnish.

  15. REMOVE UPPER NO. 2 CONSOLE PANEL GARNISH


    1. A015ZQE

      Using a moulding remover, disengage the claw.

    2. A015ZBL

      Pull the upper No. 2 console panel garnish in the direction indicated by the arrow to disengage the 2 clips and remove the upper No. 2 console panel garnish.

  16. REMOVE CONSOLE PANEL SUB-ASSEMBLY


    1. A0160RU

      Hold the front of the console panel sub-assembly as shown in the illustration and disengage the 8 clips by pulling the console panel sub-assembly in the direction shown by the arrow.

      Note

      Do not use any tools to disengage the clips. The use of tools may result in damage to the console panel sub-assembly.

    2. Disconnect the connectors and remove the console panel sub-assembly.

  17. REMOVE FRONT ASH RECEPTACLE ASSEMBLY


    1. A0161L2

      Remove the 2 screws <E>.

    2. A0163HR

      Pull the front ash receptacle assembly in the direction indicated by the arrow to disconnect the connectors and remove the front ash receptacle assembly.

  18. REMOVE REAR ASH RECEPTACLE ASSEMBLY


    1. Remove the rear ash receptacle assembly.

  19. REMOVE CONSOLE BOX REGISTER ASSEMBLY


    1. A0161O8

      Disengage the 2 claws and 4 clips, and then remove the console box register assembly.

  20. REMOVE CONSOLE BOX


    1. A0160S1

      Remove the 2 bolts.

    2. Disconnect the 2 connectors.

    3. Disengage the 2 clamps.

    4. A0162NA

      Remove the 2 bolts.

    5. Disconnect the connector.

    6. A015ZEK

      Remove the 2 bolts.

    7. A0162J5

      Disengage the 2 claws and 2 clips, and then remove the console box.

  21. REMOVE NO. 2 CONSOLE BOX DUCT


    1. A0162NO

      Remove the 2 clips and No. 2 console box duct.

  22. REMOVE FRONT DOOR SCUFF PLATE LH (for LHD)


    1. A0160BJE01

      Put protective tape around the front door scuff plate.

    2. Using a moulding remover, disengage the 4 clips.

    3. A0161H2

      Disengage the 7 claws and remove the front door scuff plate LH.

  23. REMOVE FRONT DOOR OPENING TRIM COVER LH (for LHD)


    1. A016285

      Disengage the 4 claws and remove the front door opening trim cover LH.

  24. REMOVE SIDE INSTRUMENT PANEL LH (for LHD)


    1. A015ZPA

      Using a moulding remover, disengage the 5 claws and 3 clips to remove the side instrument panel LH.

  25. REMOVE FRONT DOOR SCUFF PLATE RH (for RHD)

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  26. REMOVE FRONT DOOR OPENING TRIM COVER RH (for RHD)

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  27. REMOVE SIDE INSTRUMENT PANEL RH (for RHD)


    1. A01605Z

      Using a moulding remover, disengage the 5 claws and 3 clips to remove the side instrument panel RH.

  28. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. A0161PQE01

      Remove the 2 screws <D>.

    2. Push the 2 claws in the direction indicated by the arrow to disengage them.

    3. Remove the No. 1 instrument panel under cover sub-assembly from the guide as shown in the illustration and pull the cover toward the rear of the vehicle.

    4. Disconnect the connectors and remove the No. 1 instrument panel under cover sub-assembly.

  29. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. A0160VQ

      Disengage the 7 clips.

    2. Disconnect the connectors and remove the lower instrument panel finish panel sub-assembly.

  30. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A0160SH

      Disengage the claw and separate the hood lock control cable.

    4. A0160VX

      Remove the 4 bolts.

    5. A0161L3

      Disengage the 2 pins and separate the driver side knee airbag assembly.

    6. Disconnect the connector and remove the driver side knee airbag assembly.

      Note

      When disconnecting the airbag connector, take care not to damage the airbag wire harness.

  31. REMOVE LAP BELT OUTER ANCHOR COVER


    1. A0161TC

      Disengage the 2 claws and remove the lap belt outer anchor cover.

      Tech Tips

      Use the same procedure to remove the cover on the other side.

  32. REMOVE REAR DOOR SCUFF PLATE LH (for LHD)


    1. A0161QSE01

      Put protective tape around the rear door scuff plate.

    2. Using a moulding remover, disengage the 2 clips.

    3. A015YIJ

      Disengage the 5 claws and remove the the rear door scuff plate LH.

  33. SEPARATE FRONT SEAT OUTER BELT ASSEMBLY LH (for LHD)


    1. A015Z32

      Remove the bolt and separate the front seat outer belt assembly LH.

  34. REMOVE LOWER CENTER PILLAR GARNISH LH (for LHD)


    1. A01636PE01

      Disengage the 3 claws and 5 clips, and remove the lower center pillar garnish LH.

  35. REMOVE REAR DOOR SCUFF PLATE RH (for RHD)

    Tech Tips

    Use the same procedure for the RH side and LH side.

  36. SEPARATE FRONT SEAT OUTER BELT ASSEMBLY RH (for RHD)

    Tech Tips

    Use the same procedure for the RH side and LH side.

  37. REMOVE LOWER CENTER PILLAR GARNISH RH (for RHD)

    Tech Tips

    Use the same procedure for the RH side and LH side.

  38. REMOVE FRONT FLOOR FOOTREST LH (for LHD)


    1. Disengage the 2 clips and remove the front floor footrest LH.

  39. REMOVE FRONT FLOOR FOOTREST RH (for RHD)


    1. Disengage the 2 clips and remove the front floor footrest RH.

  40. REMOVE NO. 3 DASH PANEL INSULATOR PAD


    1. Remove the clip and No. 3 dash panel insulator pad.

  41. REMOVE FRONT FLOOR SILENCER PAD LH (for LHD)

  42. REMOVE FRONT FLOOR SILENCER PAD RH (for RHD)

  43. REMOVE REAR AIR DUCT GUIDE LH (for LHD)

  44. REMOVE REAR AIR DUCT GUIDE RH (for RHD)

  45. REMOVE NO. 2 REAR AIR DUCT (for LHD)

  46. REMOVE NO. 1 REAR AIR DUCT (for RHD)

  47. REMOVE CENTER AIRBAG SENSOR ASSEMBLY


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01624J

      Disconnect the holder (with connectors).

      Note

      When disconnecting the airbag connector, take care not to damage the airbag wire harness.

    4. Remove the 2 bolts, nut and center airbag sensor assembly.

  48. REMOVE FRONT UPPER FLOOR REAR SUB PANEL


    1. A0160GI

      Turn back the floor carpet in order to remove the front upper floor rear sub panel.

    2. Remove the 4 bolts.

    3. Disengage the 8 clamps, and remove the front upper floor rear sub panel from the body.

  49. REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY

    Tech Tips

    Refer to the instructions for Removal of the propeller shaft with center bearing assembly Click here.

  50. LOOSEN PARKING BRAKE (for LHD)


    1. A015ZDIE01

      Remove the lock nut from the No. 1 parking brake cable assembly.

    2. Loosen the No. 1 wire adjusting nut and parking brake.

  51. LOOSEN PARKING BRAKE (for RHD)


    1. A0161XRE01

      Remove the lock nut from the No. 1 parking brake cable assembly.

    2. Loosen the No. 1 wire adjusting nut and parking brake.

  52. REMOVE PARKING BRAKE RETURN WITH DAMPER SPRING


    1. A0160K2

      Remove the parking brake return with damper spring.

  53. REMOVE PARKING BRAKE EQUALIZER


    1. A0160LE

      Remove the 2 bolts, and separate the No. 2 parking brake cable assembly and No. 3 parking brake cable assembly from the parking brake equalizer.

    2. A015YK1E01

      Slide the rubber boot as shown in the illustration.

    3. A015YU5

      Remove the parking brake equalizer from the No. 1 parking brake cable assembly.

  54. REMOVE PARKING BRAKE CONTROL PEDAL ASSEMBLY (for LHD)


    1. Remove the 2 bolts and 3 nuts, and separate the No. 1 parking brake cable assembly from the body.

      A0160LO
    2. A0162J9

      Remove the 2 nuts and separate the instrument panel junction block assembly.

    3. A0161CJ

      Disconnect the parking brake switch connector.

    4. Remove the 3 nuts and parking brake control pedal assembly from the body.

  55. REMOVE NO. 1 AIR DUCT (for RHD)


    1. A015ZGF

      Disengage the claw and guide, remove the No. 1 air duct.

  56. REMOVE PARKING BRAKE CONTROL PEDAL ASSEMBLY (for RHD)


    1. A0162DZ

      Remove the 2 nuts from the No. 1 parking brake cable assembly.

    2. A0160JP

      Remove the 2 bolts, and separate the No. 1 parking brake cable assembly from the body.

    3. A0161T9

      Disconnect the parking brake switch connector.

    4. Remove the bolt, 2 nuts and parking brake control pedal assembly.