SHIFT LEVER REMOVAL


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    1. A0161TD

      Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.

  3. REMOVE UPPER NO. 1 CONSOLE PANEL GARNISH


    1. A0162WJ

      Using a moulding remover, disengage the claw.

    2. A0160YI

      Pull the upper No. 1 console panel garnish in the direction indicated by the arrow to disengage the 2 clips and remove the upper No. 1 console panel garnish.

  4. REMOVE UPPER NO. 2 CONSOLE PANEL GARNISH


    1. A015ZQE

      Using a moulding remover, disengage the claw.

    2. A015ZBL

      Pull the upper No. 2 console panel garnish in the direction indicated by the arrow to disengage the 2 clips and remove the upper No. 2 console panel garnish.

  5. REMOVE CONSOLE PANEL SUB-ASSEMBLY


    1. A0160RU

      Hold the front of the console panel sub-assembly as shown in the illustration and disengage the 8 clips by pulling the console panel sub-assembly in the direction shown by the arrow.

      Note

      Do not use any tools to disengage the clips. The use of tools may result in damage to the console panel sub-assembly.

    2. Disconnect the connectors and remove the console panel sub-assembly.

  6. REMOVE FRONT ASH RECEPTACLE ASSEMBLY


    1. A0161L2

      Remove the 2 screws <E>.

    2. A0163HR

      Pull the front ash receptacle assembly in the direction indicated by the arrow to disconnect the connectors and remove the front ash receptacle assembly.

  7. REMOVE REAR ASH RECEPTACLE ASSEMBLY


    1. Remove the rear ash receptacle assembly.

  8. REMOVE CONSOLE BOX REGISTER ASSEMBLY


    1. A0161O8

      Disengage the 2 claws and 4 clips, and then remove the console box register assembly.

  9. REMOVE CONSOLE BOX


    1. A0160S1

      Remove the 2 bolts.

    2. Disconnect the 2 connectors.

    3. Disengage the 2 clamps.

    4. A0162NA

      Remove the 2 bolts.

    5. Disconnect the connector.

    6. A015ZEK

      Remove the 2 bolts.

    7. A0162J5

      Disengage the 2 claws and 2 clips, and then remove the console box.

  10. REMOVE NO. 2 CONSOLE BOX DUCT


    1. A0162NO

      Remove the 2 clips and No. 2 console box duct.

  11. REMOVE NO. 2 FLOOR UNDER COVER


    1. A016142

      Remove the 6 clips, 3 grommets, and No. 2 floor under cover.

  12. REMOVE NO. 1 FLOOR UNDER COVER


    1. Remove the 5 clips, 3 grommets, and No. 1 floor under cover.

  13. REMOVE TAIL EXHAUST PIPE ASSEMBLY


    1. A0162QN

      Remove the 2 bolts and 2 compression springs.

    2. Remove the tail exhaust pipe assembly from the 6 exhaust pipe supports.

    3. Remove the gasket from the front exhaust pipe assembly.

  14. REMOVE REAR NO. 1 FLOOR PANEL BRACE


    1. A015YY2

      Remove the 4 bolts and rear No. 1 floor panel brace.

  15. REMOVE FRONT CENTER FLOOR BRACE


    1. A01637A

      Remove the 4 bolts and front center floor brace.

  16. DISCONNECT HEATED OXYGEN SENSOR


    1. A015ZMNE01

      Remove the grommets of the heated oxygen sensors.

    2. A0160THE01

      Using SST, loosen the heated oxygen sensors, and disconnect the sensors by hand.

      SST
      09224-00010

  17. REMOVE FRONT EXHAUST PIPE ASSEMBLY


    1. A01626I

      Remove the 4 bolts, 4 nuts and front exhaust pipe assembly.

    2. Remove the 2 gaskets from the exhaust manifold RH and exhaust manifold LH.

  18. REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR


    1. A0160RBE02

      Remove the 4 nuts, 2 bolts and front No. 1 floor heat insulator.

  19. REMOVE FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY


    1. A015YW3

      Remove the nut and separate the floor shift gear shifting rod sub-assembly.

  20. REMOVE TRANSMISSION FLOOR SHIFT ASSEMBLY


    1. A015ZEL

      Disconnect the 2 connectors.

    2. Remove the 4 clamps.

    3. Remove the 4 bolts.

    4. Remove the floor shift assembly.