REAR SUNSHADE ASSEMBLY REMOVAL

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. REMOVE COWL TOP VENTILATOR LOUVER


    1. A01GM4S

      for LHD:

      Remove the 6 clips and cowl top ventilator louver RH.

    2. A01GI9P

      for RHD:

      Remove the 6 clips and cowl top ventilator louver LH.

  2. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE REAR SEAT ASSEMBLY (for Fixed Seat Type)

    Click here

  5. REMOVE REAR SEAT ASSEMBLY (for Power Seat)

    Click here

  6. REMOVE REAR SEAT ASSEMBLY (for 4-Passenger with Ottoman)

    Click here

  7. REMOVE REAR SEAT ASSEMBLY (for 5-Passenger with Ottoman)

    Click here

  8. REMOVE REAR DOOR SCUFF PLATE LH


    1. for Standard Body:

      Click here

    2. for Long Body:

      Click here

  9. REMOVE REAR DOOR SCUFF PLATE RH


    1. for Standard Body:

      Click here

    2. for Long Body:

      Click here

  10. REMOVE REAR SEAT SIDE GARNISH LH

    A01GMSD

    1. Detach the 6 claws and remove the rear seat side garnish LH.

  11. REMOVE REAR SEAT SIDE GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  12. REMOVE INNER ROOF SIDE GARNISH LH

    A01GLGDE10
    Text in Illustration
    *1 Clip A

    1. Pull the inner roof side garnish LH away from the body to detach the 4 clips (do not detach clip A).

    2. Detach the 2 claws of the guide, and pull the inner roof side garnish LH in the direction of the arrow to remove it.

      Tech Tips

      Clip A remains attached to the body.

    3. Remove clip A from the vehicle body.

  13. REMOVE INNER ROOF SIDE GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  14. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY

    A01GMBH

    1. except 4-Passenger with Ottoman:

      Using a moulding remover D, detach the 4 claws and remove the 3 belt guides.

    2. for 4-Passenger with Ottoman:

      Using a moulding remover D, detach the 4 claws and remove the 2 belt guides.

    3. A01GJVU

      except 4-Passenger with Ottoman:

      Detach the 2 clips of the package tray trim panel. Then pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.

    4. A01GHWG

      for 4-Passenger with Ottoman:

      Detach the 2 clips of the package tray trim panel. Then pass the 2 rear seat belt floor anchors through the package tray trim panel assembly.

    5. w/o Rear Cooler:

      Remove the package tray trim panel assembly.

    6. w/ Rear Cooler:

      Disconnect the solar sensor connector and remove the package tray trim panel assembly.

  15. REMOVE NO. 2 ROOF SIDE AIR DUCT LH (w/ Rear Cooler)


    1. A01GKUC

      Remove the clip.

    2. Detach the 2 claws and remove the roof side No. 2 air duct LH.

  16. REMOVE NO. 2 ROOF SIDE AIR DUCT RH (w/ Rear Cooler)


    1. A01GJA8

      Remove the clip.

    2. Detach the 2 claws and remove the roof side No. 2 air duct RH.

  17. REMOVE REAR NO. 4 AIR DUCT (w/ Rear Cooler)


    1. A01GJG8

      Detach the 4 claws and remove the rear No. 4 air duct.

  18. REMOVE REAR NO. 5 AIR DUCT (w/ Rear Cooler)


    1. A01GJXH

      Detach the 4 claws and remove the rear No. 5 air duct.

  19. REMOVE STEREO COMPONENT SPEAKER ASSEMBLY

    Note

    Do not touch the cone part of the speaker.


    1. Disconnect the connector.

    2. Remove the 4 bolts and stereo component speaker assembly.

      A01GM9WE02
      Text in Illustration
      *A for Standard *B for 19 Speakers

  20. REMOVE NO. 2 PACKAGE TRAY TRIM PANEL ASSEMBLY

    A01GN2A

    1. Detach the 5 claws and 3 clips, and remove the No. 2 package tray trim panel assembly.

  21. REMOVE REAR SUNSHADE ASSEMBLY

    A01GJM2

    1. Remove the 4 bolts.

    2. Loosen the bolt labeled A and remove the rear sunshade assembly.

      Text in Illustration
      A01GKOV Bolt A

      Note

      Do not remove the bolt labeled A from the rear sunshade assembly.