REAR DOOR REMOVAL

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. REMOVE COWL TOP VENTILATOR LOUVER RH


    1. A01GM4S

      Remove the 6 clips and cowl top ventilator louver RH.

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG LH


    1. A01GM19

      Using a screwdriver, detach the 3 claws and remove the rear door inside handle bezel plug LH.

      Tech Tips

      Tape the screwdriver tip before use.

  5. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

    A01GJSWE01

    1. Apply protective tape to the area around the rear rear power window regulator switch assembly with rear door armrest base panel.

    2. Using a clip remover, detach the 2 clips in the order shown in the illustration.

      Text in Illustration
      *1 Protective Tape
    3. A01GKXL

      Disconnect the connector.

    4. Remove the screw and illumination light.

    5. Remove the rear rear power window regulator switch assembly with rear door armrest base panel.

  6. REMOVE ROOM TEMPERATURE SENSOR (w/ Rear Cooler)


    1. A01GKPH

      Using a screwdriver, detach the 4 claws and remove cooler thermistor, and then disconnect the connector.

  7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH (w/o Rear Door Sunshade)


    1. A01GKBY

      for Long Body:


      1. Remove the 3 screws.

      2. Detach the 13 clips.

        Note

        Do not use a tool to detach the clips of the rear door trim board sub-assembly LH.

      3. A01GKEY

        Disconnect the 2 cables from the inside handle.

      4. Disconnect the connectors and remove the trim board.

    2. A01GI80

      for Standard Body:


      1. Remove the 3 screws.

      2. Detach the 11 clips.

        Note

        Do not use a tool to detach the clips of the rear door trim board sub-assembly LH.

      3. A01GKEY

        Disconnect the 2 cables from the inside handle.

      4. Disconnect the connectors and remove the trim board.

  8. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH (w/ Rear Door Sunshade)


    1. A01GJ9M

      for Long Body:


      1. Remove the 3 screws.

      2. Detach the 14 clips.

        Note

        Do not use a tool to detach the clips of the rear door trim board sub-assembly LH.

      3. A01GKEY

        Disconnect the 2 cables from the inside handle.

      4. Disconnect the connectors and remove the rear door trim board sub-assembly LH.

    2. A01GIH1

      for Standard Body:


      1. Remove the 3 screws.

      2. Detach the 12 clips.

        Note

        Do not use a tool to detach the clips of the rear door trim board sub-assembly LH.

      3. A01GKEY

        Disconnect the 2 cables from the inside handle.

      4. Disconnect the connectors and remove the rear door trim board sub-assembly LH.

  9. REMOVE REAR DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY LH


    1. A01GJUJ

      Detach the claw, disconnect the connector and then remove the light.

  10. REMOVE COURTESY LIGHT ASSEMBLY


    1. A01GIOT

      Detach the claw.

    2. Disconnect the connector and remove the courtesy light assembly.

  11. REMOVE REAR SEAT MEMORY SWITCH (w/ Rear Seat Memory System)


    1. A01GMHO

      Disconnect the connector.

    2. Detach the 4 claws to remove the rear seat memory switch.

  12. REMOVE REAR NO. 3 SPEAKER ASSEMBLY (for 19 Speakers)

    Note

    Do not touch the cone of the speaker.


    1. A01GIEP

      Disconnect the connector.

    2. Detach the clamp, and remove the 2 screws and rear No. 3 speaker assembly.

  13. REMOVE REAR DOOR TRIM COVER LH


    1. A01GNI7

      Remove the cushion.

    2. Using a clip remover, detach the 5 clips and remove the rear door trim cover LH.

  14. REMOVE REAR DOOR FRAME GARNISH LH


    1. A01GKIM

      w/o Rear Door Sunshade:


      1. Remove the screw and detach the clip.

      2. Detach the claws and remove the rear door frame garnish LH.

    2. A01GKBI

      w/ Rear Door Sunshade:


      1. Detach the 2 clips.

      2. Detach the claws and remove the rear door frame garnish LH.

  15. REMOVE REAR DOOR NO. 3 WEATHERSTRIP LH


    1. A01GMLVE01
      Text in Illustration
      *1 Double-sided Tape

      Detach the 2 claws and remove the rear door No. 3 weatherstrip LH.

  16. REMOVE REAR DOOR NO. 2 FRAME GARNISH LH


    1. A01GMBCE04
      Text in Illustration
      *A w/o Rear Door Sunshade
      *B w/ Rear Door Sunshade

      Detach the claws and remove the rear door No. 2 frame garnish LH.

  17. REMOVE REAR DOOR NO. 2 WEATHERSTRIP LH


    1. A01GNKK

      Detach the clip and remove the rear door No. 2 weatherstrip LH.

  18. REMOVE REAR ACCESS PANEL WEATHERSTRIP LH


    1. A01GHV9E01
      Text in Illustration
      *1 Double-sided Tape

      Remove the rear access panel weatherstrip LH.

  19. REMOVE REAR CURTAIN SUB-ASSEMBLY LH (w/ Rear Door Sunshade)


    1. A01GM0R

      for Standard Body:


      1. Remove the 10 screws.

      2. Detach the 3 clips and remove the rear curtain sub-assembly LH.

      3. Disconnect the connector

    2. A01GKVH

      for Long Body:


      1. Remove the 10 screws.

      2. Detach the 4 clips and remove the rear curtain sub-assembly LH.

      3. Disconnect the connector

  20. REMOVE NO. 1 AUTO CURTAIN RAIL BRACKET LH (w/ Rear Door Sunshade)


    1. A01GK25

      Using a clip remover, detach the clip and remove the No. 1 auto curtain rail bracket LH.

  21. REMOVE REAR SIDE TRIM BOARD COVER LH (w/ Rear Door Sunshade)


    1. A01GJMZ

      Remove the 2 screws and rear side trim board cover LH.

  22. REMOVE REAR DOOR GLASS INNER WEATHERSTRIP LH


    1. for Long Body:


      1. A01GNR8

        Remove the rear door glass inner weatherstrip LH by pulling it upward in the direction indicated by the arrow.

    2. for Standard Body:


      1. A01GK80

        Remove the rear door glass inner weatherstrip LH by pulling it upward in the direction indicated by the arrow.

  23. REMOVE REAR NO. 1 SPEAKER ASSEMBLY

    Note

    Do not touch the cone of the speaker.


    1. Disconnect the connector.

      A01GL29E02
      Text in Illustration
      *A for Standard *B for 19 Speakers

    2. Remove the 2 screws.

    3. Detach the clip and remove the rear No. 1 speaker assembly.

  24. REMOVE REAR DOOR SPEAKER COVER


    1. A01GJZY

      Remove the 3 screws.

    2. Disconnect the claw and remove the rear door speaker cover.

  25. REMOVE REAR NO. 2 SPEAKER ASSEMBLY (for 19 Speakers)

    Note

    Do not touch the cone of the speaker.


    1. A01GJ8W

      Disconnect the connector.

    2. Remove the 3 screws.

    3. Detach the claw and remove the rear No. 2 speaker assembly.

  26. REMOVE REAR DOOR ECU LH


    1. A01GLZ7E02

      Remove the 2 screws and rear door ECU LH.

    2. Disconnect the 3 connectors.

  27. REMOVE REAR DOOR SERVICE HOLE COVER LH


    1. A01GLVD

      Remove the rear door service hole cover LH.

  28. REMOVE REAR DOOR DIVISION BAR LOWER BRACKET LH


    1. A01GINF

      Remove the 3 nuts and rear door division bar lower bracket LH.

  29. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH


    1. A01GKT1

      Remove the 2 nuts.

    2. Remove the rear door window division bar sub-assembly LH together with the rear door glass run LH.

  30. REMOVE REAR DOOR GLASS RUN LH


    1. Remove the rear door glass run LH from the division bar assembly.

  31. REMOVE REAR DOOR QUARTER WINDOW GLASS LH


    1. A01GKG3

      Remove the rear door quarter window glass LH and rear door quarter window weatherstrip LH as a unit as shown in the illustration.

  32. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH


    1. Remove the hole plug.

    2. A01GNLC

      Remove the 2 bolts.

      Note

      Be careful when removing the bolts as the glass may fall and become damaged.

    3. Remove the rear door glass sub-assembly LH.

      Tech Tips

      Remove the glass upward.

      Note

      Be careful not to damage the glass.

  33. REMOVE REAR DOOR UPPER WINDOW FRAME MOULDING LH


    1. for Standard Body:

      Click here

    2. for Long Body:

      Click here

  34. REMOVE REAR DOOR BELT MOULDING LH


    1. A01GL32

      Remove the 2 screws.

    2. A01GJGI

      Loosen the 5 belt line screws indicated by the arrows in the illustration.

    3. Remove the 3 screws.

    4. A01GM5RE02

      Put protective tape around the rear door belt moulding LH.

    5. While making sure not to pull the rear door belt moulding LH away from the vehicle, rotate the rear door belt moulding LH in the direction shown in the illustration and remove it.

      Note

      Be careful not to damage the door panel when rotating the belt moulding.

      Tech Tips

      The clip will break when the rear belt moulding is removed.

    6. Remove the remaining part of the clip from the body.

      Text in Illustration
      *1 Protective Tape

  35. REMOVE REAR DOOR FRONT WINDOW GUIDE SUB-ASSEMBLY LH


    1. A01GN9B

      Remove the 2 bolts and rear door front window guide sub-assembly LH.

  36. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH


    1. Disconnect the connector.

    2. A01GKXFE04
      Text in Illustration
      *1 Temporary Bolt

      Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the window regulator may fall and become damaged.

    3. Remove the 3 bolts and rear door window regulator sub-assembly LH.

      Note

      Be careful when removing the screws as the motor may fall and become damaged.

    4. Remove the temporary bolt from the rear door window regulator sub-assembly LH.

  37. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


    1. A01GIR9

      Using a T25 ''TORX'' driver, remove the 3 screws and power window regulator motor assembly LH.

      Note

      Be careful when removing the screws as the motor may fall and become damaged.

  38. REMOVE REAR DOOR LOCK ASSEMBLY LH


    1. A01GHYLE01

      Disconnect the 2 connectors and detach the 2 clamps.

    2. Using a T30 'TORX' socket, remove the 3 screws labeled A and 2 screws labeled B.

    3. Remove the rear door lock assembly LH.

      Note

      Be careful when removing the bolts as the door lock may fall and become damaged.

      Tech Tips

      Remove the door lock through the service hole.

  39. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    1. A01GKGOE04
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the claw.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A01GKQS

      Remove the rear door lock remote control cable assembly LH.

  40. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    1. A01GMEEE06

      Using a screwdriver, detach the 3 claws.

      Tech Tips

      Tape the screwdriver tip before use.

      Text in Illustration
      *1 Protective Tape
    2. A01GIP6

      Remove the rear door inside locking cable assembly LH.

  41. REMOVE REAR DOOR OUTSIDE HANDLE COVER LH


    1. A01GIY9

      Using a T30 ''TORX'' socket, loosen the screw and remove the rear door outside handle cover LH.

  42. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH


    1. A01GHRC

      Using a T30 "TORX" wrench, loosen the screw.

    2. A01GIR6

      Disconnect the connector.

    3. Remove the rear door outside handle assembly LH by sliding and pulling it in the direction indicated by the arrow in the illustration.

  43. REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH


    1. A01GJOC

      Using a T30 ''TORX'' socket, remove the screw and rear door outside handle frame sub-assembly LH.

      Tech Tips

      Remove the outside handle frame through the service hole.

    2. A01GMQE

      Disconnect the connector and detach the 3 clamps.

  44. REMOVE DOOR ELECTRICAL KEY OSCILLATOR (for Rear Door)


    1. A01GNLU

      Remove the screw and door electrical key oscillator.

  45. REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD


    1. A01GJYA

      Detach the 3 claws and remove the rear door front outside handle pad.

  46. REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD


    1. A01GJQR

      Detach the 2 claws and remove the rear door rear outside handle pad.

  47. REMOVE REAR DOOR CHECK COVER LH


    1. A01GN9K

      Remove the rear door check cover LH.

  48. REMOVE REAR DOOR CHECK ASSEMBLY LH


    1. A01GLI9

      Remove the bolt, 2 nuts and rear door check assembly LH.

      Tech Tips

      Remove the door check through the service hole.

      Note

      Be careful when removing the bolts as the door check may fall and become damaged.

  49. REMOVE REAR DOOR WEATHERSTRIP LH


    1. for Long Body:


      1. A01GHT7

        Detach the 19 clips and remove the rear door weatherstrip LH.

    2. for Standard Body:


      1. A01GJRL

        Detach the 18 clips and remove the rear door weatherstrip LH.