REPAIR INSTRUCTION INITIALIZATION


  1. PROCEDURES NECESSARY WHEN CABLE IS DISCONNECTED/RECONNECTED TO BATTERY TERMINAL

    Procedures Necessary when Cable is Disconnected/Reconnected to Battery Terminal
    Necessary Procedures Effects / Inoperative Functions When Necessary Procedures are not Performed See page
    Steering angle sensor zero point calibration Adaptive high beam system

    Click here

    Correction of steering angle neutral point Parking assist monitor system

    Click here

    Reset rear door sunshade system Rear door curtain function

    Click here

    Reset power trunk lid system Power trunk lid function

    Click here

    Note

    After the engine switch is turned off, the multi-media module receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

    Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal
    Condition Waiting Time
    Vehicle enrolled in G-BOOK system 6 minutes
    Vehicle not enrolled in G-BOOK system 1 minute

    CAUTION:

    Make sure that the bracket of the earth wire is fixed to the vehicle body with the ground bolt.

  2. PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED

    Procedures Necessary when ECU or Other Parts are Replaced
    Replacement Part Necessary Procedures Effects / Inoperative Functions When Necessary Procedures are not Performed See Page

      for 1UR-FE

    • ECM

    Register VIN DTC P0630 is output

    Click here

    Register cruise control system Cruise control system

    Click here


      for 1UR-FSE

    • ECM

    Register VIN -

    Click here

    Register cruise control system Cruise control system

    Click here


      for AA80F

    • Automatic w/transfer transmission assembly


    • Set transmission compensation code

    • Learning by driving (Road test)

    • Reset memory


    • Large shift shock

    • Engine overruns

    Click here


      for AA80E

    • Automatic transmission assembly


    • Set transmission compensation code

    • Learning by driving (Road test)

    • Reset memory


    • Large shift shock

    • Engine overruns

    Click here


      for AA80F

    • Valve body assembly

    • Shift solenoid valve SL1, 2, 3, 4, 5

    Learning by driving (Road test)
    • Large shift shock

    • Engine overruns

    Click here


      AA80E

    • Valve body assembly

    • Shift solenoid valve SL1, 2, 3, 4, 5

    Learning by driving (Road test)
    • Large shift shock

    • Engine overruns

    Click here


      for AA80F

    • TCM


    • Set transmission compensation code

    • Learning by driving (Road test)


    • Large shift shock

    • Engine overruns

    Click here


      for AA80E

    • TCM


    • Set transmission compensation code

    • Learning by driving (Road test)


    • Large shift shock

    • Engine overruns

    Click here


      for AA80F

    • Engine assembly

    • ECM


    • Reset memory

    • Learning by driving (Road test)


    • Large shift shock

    • Engine overruns

    Click here


      for AA80E

    • Engine assembly

    • ECM


    • Reset memory

    • Learning by driving (Road test)


    • Large shift shock

    • Engine overruns

    Click here


    • Suspension control ECU

    • Height control sensor


    • Vehicle height offset calibration

    • Registration of vehicle identification information


    • Vehicle height sensor data may be affected due to installation position, or vehicle height recognition may be erroneous

    • DTC C1789 is output

    • Negative effect on the other systems.

    Click here


    • Tire pressure warning ECU and receiver

    • Tire pressure warning valve and transmitter


    1. Register transmitter IDs

    2. Initialization


    • When DTC detection conditions of "transmitter ID not received" DTC is met, tire pressure warning light blinks for 1 minute, and then illuminates

    • Tire pressure monitoring function

    Click here (for Registration)

    Click here (for Initialization)


    • Skid control ECU


    • Initialize linear solenoid valve and perform calibration

    • Perform yaw rate and acceleration sensor zero point calibration


    • Brake warning light / yellow (minor malfunction) illumination

    • Brake warning light / red (malfunction)

    • ABS warning light illumination

    • Slip indicator light illumination

    Click here (for Initialization)

    Click here (for Calibration)


    • Brake actuator


    1. Bleed air

    2. Clear stored value of linear solenoid valve and calibration data

    3. Initialize linear solenoid valve and perform calibration

    Brake does not operate properly

    Click here


    • Brake pedal stroke sensor

    • Brake pedal


    1. Inspect and adjust brake pedal height

      Adjust brake pedal stroke sensor

    2. Clear stored value of linear solenoid valve and calibration data

    3. Initialize linear solenoid valve and perform calibration


    • Brake warning light / yellow (minor malfunction) illumination

    • Brake warning light / red (malfunction)

    • ABS warning light illumination

    • Slip indicator light illumination

    Click here


    • Yaw rate sensor


    1. Clear zero point calibration data

    2. Perform yaw rate and acceleration sensor zero point calibration


    • Brake warning light / yellow (minor malfunction) illumination

    • Brake warning light / red (malfunction)

    • ABS warning light illumination

    • Slip indicator light illumination

    • VSC control is prohibited or operation is incorrect

    • VGRS system

    Click here


    • Electric parking brake ECU


    • Reset memory

    • Acquire tension sensor zero point

    Electric parking brake does not operate normally

    Click here


    • Parking brake with bracket actuator assembly


    • Reset memory

    • Acquire tension sensor zero point

    • Parking brake bedding


    • Electric parking brake does not operate normally

    • Parking brake performance may not be normal

    Click here


    • Rear disc

    • Parking brake shoe

    Parking brake bedding Parking brake performance may not be normal

    Click here


    • Steering control ECU

    • Steering column

    • Steering intermediate shaft

    Actuator angle neutral point calibration and initialization Steering wheel off-center

    Click here


    • Power steering link assembly


    • Actuator angle neutral point calibration and initialization

    • Rotation angle sensor value initialization

    • Torque sensor zero point calibration

    • VGRS system calibration procedure


    • Steering wheel off-center

    • Difference in amount of steering assist between left and right

    Click here


    • Power steering ECU


    • Rotation angle sensor value initialization

    • Torque sensor zero point calibration


    • Steering wheel off-center

    • Difference in amount of steering assist between left and right

    Click here


      w/ Blocking System

    • Telephone Transceiver Assembly

    • Mayday Battery

    • Instrument Panel Integration antenna Assembly

    Registration Engine Starting Refer to the Service Bulletin for the registration procedure.

    • Rear bumper cover

    Inspect rear millimeter wave radar sensor

    (Rear radar sensor check)

    Rear millimeter wave radar sensor sensitivity may decrease

    Click here


    • Rear millimeter wave radar sensor

    Adjust rear millimeter wave radar sensor DTC C1A13 or C1A15 is output

    Click here


    • Object recognition ECU

    • Object recognition camera sensor

    Adjust object recognition camera DTC C1A22 or C1A23 is output

    Click here


    • No. 1 night view ECU

    • Object recognition camera (night view camera)

    Adjust object recognition camera (night view camera) DTC B281A, B2827, C1A22 AND C1A3 are output

    Click here


    • Driving support ECU

    Initialize driving support ECU Object recognition camera does not operate normally

    Click here


    • Front millimeter wave radar sensor

    Adjust front millimeter wave radar sensor DTC C1A11 or C1A14 is output

    Click here


    • Steering angle sensor

    Initialize parking assist monitor system
    • VGRS system

    • Parking assist function

    Click here


    • Television camera assembly

    Television camera optical axis

    (Camera position setting)

    Vehicle width extension lines and expected course are deviated

    Click here


    • Windshield glass

    Adjust adaptive high beam camera beam axis DTC B2454 is output

    Click here


    • Inner rear view mirror assembly


    • Registration

    • Adjust Adaptive High Beam Camera Beam Axis


    • Garage door opener function

    • DTC B2454 output

    • Adaptive High Beam does not operate normally

    Click here

    Power window regulator motor

    (All doors)

    Initialize power window control system
    • AUTO UP / DOWN

    • Jam protection

    • Key-off

    Click here


    • Front power seat switch

      (Seat ECU)

    • Front seat adjuster

    Position sensor initialization
    • During manual operation, buzzer sounds

    • Memory function does not operate

    • Interference stop control does not operate normally

    • Linked control does not operate normally

    Click here


    • Position control ECU

    • Rear seat adjuster

    Position sensor initialization
    • During manual operation, buzzer sounds

    • Memory function does not operate

    • Interference stop control does not operate normally

    • Linked control does not operate normally

    Click here


    • RR MPX-B1 fuse

    • Luggage closer motor assembly

    • Luggage door closer assembly

    Reset power trunk lid system Power trunk lid function

    Click here


    • Rear door ECU LH

    • Rear door ECU RH

    • Rear curtain

    Rear curtain position reset operation Rear curtain function

    Click here


    • Sliding roof drive gear

      (Sliding roof ECU)

    • Sliding roof housing

    • Sliding roof glass

    Initialize sliding roof system
    • Auto operation

    • Jam protection function

    • Sliding roof operation after engine switch is turned off

    • Wireless door lock control function

    • Key-linked operation function

      (Driver's door only)

    • Entry lock switch-linked operation

    Click here


    • ID code box

    • Steering lock ECU

    • ECM

    • Key

    • Certification ECU

    Registration
    • Wireless door lock operation

    • Entry operation

    • Engine starting

    • Steering unlock

    Refer to service Bulletin for registration procedure

    • Multi-media module receiver assembly

    • Telematics Transceiver

    Vehicle contract setting
    • G-BOOK service

    • Emergency call service

    Click here


    • Hard disc

    Download necessary data Some G-BOOK service content will be unavailable

    Click here