AIR HOSE (for Ottoman) REMOVAL

Tech Tips


  • Use the same procedure for LHD and RHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. REMOVE COWL TOP VENTILATOR LOUVER RH


    1. A01GM4S

      for LHD:

      Remove the 6 clips and cowl top ventilator louver RH.

    2. A01GI9P

      for RHD:

      Remove the 6 clips and cowl top ventilator louver LH.

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE REAR SEAT CUSHION ASSEMBLY LH

    A01GLQWE01

    1. Detach the 2 front hooks of the rear seat cushion assembly LH from the rear No. 2 seat adjuster assembly.

      Note


      • If the areas close to the insertion location of the rear seat cushion lock hooks (A) are not lifted straight up, the cushion spring may become deformed.

      • When lifting the rear seat cushion assembly, lift it quickly so that force is applied directly to the hooks. Do not lift it slowly.

      Specification
      Area Measurement
      a 114 mm (4.49 in.)
      b 100 mm (3.94 in.)

    2. Detach the rear hook of the rear seat cushion assembly LH to remove the rear seat cushion assembly LH from the rear seatback spring assembly LH.

      Note

      Be careful not to damage the vehicle body.

    3. Disconnect the connector.

  5. REMOVE REAR SEAT CUSHION ASSEMBLY RH


    1. Connect the cable to the negative (-) battery terminal.

    2. Operate the ottoman switch to move the ottoman to the return position.

    3. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    4. A01GMJ8E01
      Text in Illustration
      *1 Protective Tape
      *2 Seat Cover Hook
      *3 Nut
      *4 Rear Seat Cushion Lock Hook
      *5 Rear Hook

      Put protective tape as shown in the illustration.

    5. Remove the 2 seat cushion cover hooks.

    6. Remove the 2 nuts and disconnect the seat cushion ottoman part.

    7. Lift the corners of the rear seat cushion assembly RH to disconnect the 2 rear seat cushion lock hooks.

      Note


      • If the areas close to the insertion location of the rear seat cushion lock hooks (cushion assembly corners) are not lifted straight up, the cushion spring may become deformed.

      • When lifting the rear seat cushion assembly, lift it quickly so that force is applied directly to the hooks. Do not lift it slowly.

    8. Detach the rear hook of the rear seat cushion assembly RH to remove the rear seat cushion assembly RH from the rear seatback spring assembly RH.

      Note

      Be careful not to damage the vehicle body.

    9. Disconnect the connector.

  6. REMOVE REAR CENTER SEAT CUSHION ASSEMBLY (w/ Center Seat)


    1. A01GJWX

      Detach the front hook of the rear center seat cushion assembly from the vehicle body.

      Note

      The cushion frame deforms easily. To avoid deforming the rear center seat cushion assembly, place your hands near the hook, and then pull up on the rear center seat cushion assembly.

    2. Detach the rear hook of the rear center seat cushion assembly to remove the rear center seat cushion assembly from the center seatback frame sub-assembly.

      Note

      Be careful not to damage the vehicle body.

  7. REMOVE REAR SEAT CONSOLE BOX (w/ Rear Console Box)

    Click here

  8. REMOVE REAR SEATBACK ASSEMBLY LH


    1. A01GMB3

      Remove the bolt and disconnect the anchor part of the rear seat 3 point type belt assembly LH.

    2. A01GI1OE03

      Using a screwdriver, detach the 2 claws and open the 2 caps of the rear seat shoulder belt guide.

      Tech Tips

      Tape the screwdriver tip before use.

      Text in Illustration
      *1 Protective Tape

    3. Disconnect the rear seat 3 point type belt assembly from the shoulder belt guide.

    4. A01GN8I

      Remove the bolt and pull out the junction block.

    5. Disconnect the 2 connectors.

    6. A01GL9B

      Detach the 7 wire harness clamps and disconnect the 3 connectors.

    7. A01GKZ2E01
      Text in Illustration
      *1 Fastening Tape

      Detach the 3 pieces of fastening tape and using a clip remover, detach the clip.

    8. Remove the 2 nuts and disconnect the air duct from the vehicle.

    9. Disconnect the rear seatback assembly LH from the rear No. 2 seat adjuster assembly and lift the rear seatback assembly LH upwards to remove it.

      Note

      Be careful not to damage the vehicle body.

  9. REMOVE REAR SEATBACK ASSEMBLY RH


    1. A01GNJU

      Remove the bolt and disconnect the anchor part of the rear seat 3 point type belt assembly RH.

    2. A01GN5BE01

      Using a screwdriver, detach the 2 claws and open the 2 caps of the rear seat shoulder belt guide.

      Tech Tips

      Tape the screwdriver tip before use.

      Text in Illustration
      *1 Protective Tape

    3. Remove the seat belt from the shoulder belt guide.

    4. A01GI1Y

      Remove the bolt and pull out the junction block.

    5. Disconnect the 3 connectors.

    6. A01GLLP

      Detach the 6 wire harness clamps and disconnect the 3 connectors.

    7. A01GM7AE01

      Remove the nut, detach the 2 claws and disconnect the air hose.

    8. Detach the 3 pieces of fastening tape and using a clip remover, detach the clip.

    9. Remove the 2 nuts and disconnect the air duct from the vehicle.

    10. Disconnect the rear seatback assembly RH from the rear No. 2 seat adjuster assembly and lift the rear seatback assembly RH upwards to remove it.

      Note

      Be careful not to damage the vehicle body.

      Text in Illustration
      *1 Air Hose
      *2 Fastening Tape
      *3 Air Duct

  10. REMOVE REAR SEAT CENTER ARMREST ASSEMBLY (w/ Center Seat)


    1. Lower the rear seat center armrest assembly.

    2. A01GNG6

      Raise the rear center seat headrest assembly.

    3. A01GO13E04

      Detach the 2 clips.

    4. Detach the hook by lowering the rear seat armrest hole board, and remove it.

    5. A01GJRU

      Remove the 2 bolts, nut and rear seat center armrest assembly.

      Note

      Be careful not to damage the vehicle body.

    6. Disconnect the 2 connectors.

  11. REMOVE REAR DOOR SCUFF PLATE LH

    A01GLJ9E06

    1. Put protective tape around the front door scuff plate LH.

      Text in Illustration
      *1 Protective Tape

    2. Using moulding remover D, detach the 4 clips.

    3. A01GNER

      Detach the 7 claws and remove the front door scuff plate LH.

  12. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  13. REMOVE REAR SEAT SIDE GARNISH LH

    A01GMSD

    1. Detach the 6 claws and remove the rear seat side garnish LH.

  14. REMOVE REAR SEAT SIDE GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  15. REMOVE INNER ROOF SIDE GARNISH LH

    A01GLGDE10
    Text in Illustration
    *1 Clip A

    1. Pull the inner roof side garnish LH away from the body and detach the 4 clips (do not detach clip A).

    2. Detach the 2 claws of the guide, and pull the inner roof side garnish LH in the direction of the arrow to remove it.

      Tech Tips

      Clip A remains attached to the body.

    3. Remove clip A from the vehicle body.

  16. REMOVE INNER ROOF SIDE GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  17. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY

    A01GMBH

    1. except 4-Passenger with Ottoman:

      Using a moulding remover D, detach the 4 claws and remove the 3 belt guides.

    2. for 4-Passenger with Ottoman:

      Using a moulding remover D, detach the 4 claws and remove the 2 belt guides.

    3. A01GJVU

      except 4-Passenger with Ottoman:

      Detach the 2 clips of the package tray trim panel. Then pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.

    4. A01GHWG

      for 4-Passenger with Ottoman:

      Detach the 2 clips of the package tray trim panel. Then pass the 2 rear seat belt floor anchors through the package tray trim panel assembly.

    5. w/o Rear Cooler:

      Remove the package tray trim panel assembly.

    6. w/ Rear Cooler:

      Disconnect the solar sensor connector and remove the package tray trim panel assembly.

  18. REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

    A01GIID

  19. REMOVE ROPE HOOK ASSEMBLY


    1. A01GMHF

      Remove the 4 bolts and 4 rope hook assemblies.

  20. REMOVE ROPE HOOK


    1. A01GJF0

      Remove the 4 rope hooks by pushing the claws in the direction of the arrows in the illustration.

  21. REMOVE DECK TRIM SIDE BOARD LH


    1. A01GJT4E02
      Text in Illustration
      *A w/ Spare Tire
      *B w/o Spare Tire

      w/ Spear Tire:


      1. Remove the clip.

      2. Remove the deck trim side board LH.

    2. w/o Spear Tire:


      1. Detach the clip and deck trim side board LH.

  22. REMOVE DECK TRIM SIDE BOARD RH


    1. A01GL8HE02
      Text in Illustration
      *A w/ Spare Tire
      *B w/o Spare Tire

      w/ Spear Tire:


      1. Remove the clip.

      2. Remove the deck trim side board RH.

    2. w/o Spear Tire:


      1. Detach the clip and deck trim side board RH.

  23. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY


    1. A01GN4SE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 2 claws and remove the No. 1 luggage compartment light assembly.

      Tech Tips

      Tape the screwdriver tip before use.

  24. REMOVE NO. 2 LUGGAGE COMPARTMENT TRIM HOOK (w/o Rear Cooler)


    1. Detach the No. 2 luggage compartment trim hook.

  25. REMOVE NO. 1 COOLER COVER (w/ Rear Cooler)


    1. A01GI3S

      Detach the 2 clips and remove the No. 1 cooler cover.

  26. REMOVE LUGGAGE COMPARTMENT TRIM COVER SUB-ASSEMBLY FRONT


    1. w/o Rear Cooler:


      1. A01GJSC

        Remove the 4 claws, 3 clips and front luggage compartment trim cover.

    2. w/ Rear Cooler:


      1. A01GI60

        Remove the 4 claws, 5 clips and front luggage compartment trim cover.

  27. REMOVE DECK BOARD ASSEMBLY (w/o Spare Tire)

  28. REMOVE TOOL BOX (w/o Spare Tire)

    A01GI61

    1. Remove the 2 clips and tool box.

  29. REMOVE REAR FLOOR FINISH PLATE


    1. A01GHU1

      Remove the 3 clips.

    2. Detach the 4 clips and remove the rear floor finish plate.

  30. REMOVE LUGGAGE COMPARTMENT TRIM COVER ASSEMBLY LH


    1. A01GJ4PE02
      Text in Illustration
      *A w/o Rear Cooler
      *B w/ Rear Cooler

      Remove the 2 clips.

    2. Detach the claw and luggage compartment trim cover assembly LH.

  31. REMOVE LUGGAGE COMPARTMENT TRIM COVER ASSEMBLY RH


    1. A01GMS7E01
      Text in Illustration
      *A w/o Rear Cooler
      *B w/ Rear Cooler

      Remove the 2 clips.

    2. Detach the claw and luggage compartment trim cover assembly RH.

  32. REMOVE ROOF SIDE NO. 2 AIR DUCT LH


    1. A01GKUC

      Remove the clip.

    2. Detach the 2 claws and remove the roof side No. 2 air duct LH.

  33. REMOVE REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH


    1. A01GI00

      Using a screwdriver, pull out the locking button in the direction shown by the arrow in the illustration to release the lock, and disconnect the pretensioner connector as shown in the illustration.

      Tech Tips

      Tape the screwdriver tip before use.

    2. w/ Tension Reducer System:

      Disconnect the tension reducer connector.

    3. A01GLNO

      Remove the bolt.

    4. Detach the claw and remove the rear seat 3 point type belt assembly LH.

  34. REMOVE AIR HOSE


    1. A01GMJM

      Disconnect the air hose connector.

    2. Remove the 2 hose clamps.

    3. A01GJIU

      Remove the bolt and 2 hose clamps.

    4. for RHD:

      Remove the bolt and hose clamp.

    5. Detach the 2 claws and remove the air hose.