POWER WINDOW REGULATOR MOTOR (for Front Door) REMOVAL

Tech Tips


  • Use the same procedures for the LH side and RH side.

  • The procedures listed below are for the LH side.


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work. Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE DOOR INSIDE HANDLE BEZEL PLUG


    1. A01GLM0E03
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 3 claws and remove the front door inside handle bezel plug LH.

      Tech Tips

      Tape the screwdriver tip before use.

  4. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL


    1. A01GLW8

      Using a screwdriver, disengage the 2 clips.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Disconnect the connector and remove the multiplex network master switch assembly.

  5. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for RHD)


    1. A01GNUN

      Using a screwdriver, disengage the 2 clamps.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Disconnect the 2 connectors and remove the front power window regulator switch assembly.

  6. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A01GJPZ

      Remove the 3 screws.

    2. Detach the 13 clips and remove the front door trim board sub-assembly LH.

    3. Disconnect the connector.

    4. A01GL8K

      Disconnect the 2 cables from the inside handle.

  7. REMOVE FRONT DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY LH


    1. A01GJXN

      Detach the claw, disconnect the connector and then remove the front door inside handle illumination light assembly LH.

  8. REMOVE COURTESY LIGHT ASSEMBLY


    1. A01GKR8

      Detach the claw and remove the courtesy light assembly.

    2. Disconnect the connector.

  9. REMOVE FRONT DOOR TRIM COVER LH


    1. A01GHO9E01
      Text in Illustration
      *1 Cushion

      Remove the cushion.

    2. Using a clip remover, detach the 5 clips.

  10. REMOVE DOOR FRAME GARNISH LH


    1. A01GMGE

      Remove the 2 clips and door frame garnish LH.

  11. REMOVE FRONT DOOR SERVICE HOLE COVER LH


    1. A01GMN8

      Remove the front door service hole cover LH.

      Tech Tips

      Remove the remaining tape on the door.

  12. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH


    1. Connect the front door ECU LH.

    2. Temporarily install the power window regulator master switch assembly with front door armrest base panel.

    3. Connect the cable to the negative (-) battery terminal.

    4. Remove the hole plug.

    5. A01GJGP

      Move the front window regulator sub-assembly LH so that the front door glass sub-assembly LH bolts can be seen.

    6. Disconnect the cable from the negative (-) battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    7. Remove the 2 bolts.

      Note

      Be careful when removing the bolts as the glass may fall and become damaged.

    8. A01GLB9

      Remove the front door glass sub-assembly in the direction indicated by the arrows in the illustration.

      Tech Tips

      Remove the glass upward.

      Note

      Be careful not to damage the glass.

    9. Remove the power window regulator master switch assembly with front door armrest base panel.

    10. Disconnect the front door ECU LH.

  13. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH


    1. A01GJU2E05
      Text in Illustration
      *1 Temporary Bolt

      Disconnect the connector.

    2. Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator sub-assembly LH may fall and become damaged.

    3. Remove the 5 bolts and front door window regulator sub-assembly LH.

      Tech Tips

      Remove the window regulator through the service hole.

      Note

      Be careful when removing the bolts as the window regulator may fall and become damaged.

    4. Remove the temporary bolt from the front door window regulator sub-assembly LH.

  14. REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


    1. A01GKJG

      Using a T25 "TORX" driver, remove the 3 screws and power window regulator motor assembly LH.

      Note

      Be careful when removing the screws as the motor may fall and become damaged.