FRONT DOOR LOCK REMOVAL

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. REMOVE COWL TOP VENTILATOR LOUVER RH


    1. A01GM4S

      Remove the 6 clips and cowl top ventilator louver RH.

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE DOOR INSIDE HANDLE BEZEL


    1. A01GLM0E03
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 3 claws and remove the front door inside handle bezel plug LH.

      Tech Tips

      Tape the screwdriver tip before use.

  5. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY LH

  6. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A01GJPZ

      Remove the 3 screws.

    2. Detach the 13 clips and remove the front door trim board sub-assembly LH.

    3. Disconnect the connector.

    4. A01GL8K

      Disconnect the 2 cables from the inside handle.

  7. REMOVE FRONT DOOR TRIM COVER LH


    1. A01GHO9E01
      Text in Illustration
      *1 Cushion

      Remove the cushion.

    2. Using a clip remover, detach the 5 clips.

  8. REMOVE FRONT DOOR SERVICE HOLE COVER LH


    1. A01GMN8

      Remove the front door service hole cover LH.

      Tech Tips

      Remove the remaining tape on the door.

  9. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH


    1. Connect the front door ECU LH.

    2. Temporarily install the power window regulator master switch assembly with front door armrest base panel.

    3. Connect the cable to the negative (-) battery terminal.

    4. Remove the hole plug.

    5. A01GJGP

      Move the front window regulator sub-assembly LH so that the front door glass sub-assembly LH bolts can be seen.

    6. Disconnect the cable from the negative (-) battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    7. Remove the 2 bolts.

      Note

      Be careful when removing the bolts as the glass may fall and become damaged.

    8. A01GLB9

      Remove the front door glass sub-assembly in the direction indicated by the arrows in the illustration.

      Tech Tips

      Remove the glass upward.

      Note

      Be careful not to damage the glass.

    9. Remove the power window regulator master switch assembly with front door armrest base panel.

    10. Disconnect the front door ECU LH.

  10. REMOVE FRONT DOOR FRAME SUB-ASSEMBLY REAR LOWER LH


    1. A01GJHE

      Remove the 2 bolts and front door rear lower frame sub-assembly LH.

  11. REMOVE FRONT DOOR OUTSIDE HANDLE COVER LH


    1. A01GNHQ

      Remove the hole plug.

    2. Using a T30 "TORX" wrench, loosen the screw and remove the front door outside handle cover LH with the door lock key cylinder installed.

    3. Remove the cylinder from the front door outside handle cover LH.

  12. REMOVE FRONT DOOR LOWER FRAME GARNISH PAD LH


    1. A01GJT8

      Remove the 2 bolts and front door lower frame garnish pad LH.

  13. REMOVE FRONT DOOR LOCK ASSEMBLY LH


    1. A01GHLBE01

      Disconnect the 2 connectors.

    2. Using a T30 "TORX" wrench, remove 3 screws labeled A and the 2 screws labeled B.

    3. Remove the front door lock assembly LH.

      Note

      Be careful when removing the bolts as the door lock may fall and become damaged.

      Tech Tips

      Remove the door lock through the service hole.

  14. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    1. A01GKGOE03
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the claw.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A01GKQS

      Remove the front door lock remote control cable assembly LH.

  15. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    1. A01GMEEE05
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 3 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A01GIP6

      Remove the front door inside locking cable assembly LH.