CAN COMMUNICATION SYSTEM (for RHD) TERMINALS OF ECU

Tech Tips

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


    1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and CAN branch wire.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note


      • Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the engine switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

      • After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

      • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. JUNCTION CONNECTOR


    1. NO. 1 JUNCTION CONNECTOR

      A01GLQAE64
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 1 Junction Connector)

      		 *b for No. 2 Junction Connector [Steering Bus]
      *c for Steering Control ECU (w/ Variable Gear Ratio Steering System) *d for ECM [Steering Bus]
      *e for Driving Support ECU Assembly (w/ Pre-crash Safety System) *f for ECM [V Bus]
      *g for Electric Power Control ECU (Passenger Side Junction Block) *h for No. 2 Junction Connector [V Bus]
      No. 1 Junction Connector Wiring Color Connect to
      A67-1 (CANH) B No. 2 junction connector [Steering bus]
      A67-12 (CANL) W
      A67-2 (CANH) B Steering Control ECU*1
      A67-13 (CANL) W
      A67-3 (CANH) B ECM [Steering bus]
      A67-14 (CANL) W
      A67-4 (CANH) B Driving support ECU assembly*2
      A67-15 (CANL) W
      A67-9 (CANH) R ECM [V bus]
      A67-20 (CANL) G
      A67-10 (CANH) R Electric power control ECU (passenger side junction block)
      A67-21 (CANL) G
      A67-11 (CANH) R No. 2 junction connector [V bus]
      A67-22 (CANL) G

      • *1: w/ Variable Gear Ratio Steering System

      • *2: w/ Pre-crash Safety System

    2. NO. 2 JUNCTION CONNECTOR

      A01GLQAE91
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 2 Junction Connector)

      		 *b for No. 3 Junction Connector
      *c for Air Conditioning Amplifier Assembly *d for Multi-media Module Receiver Assembly
      *e for No. 1 Junction Connector [V Bus] *f for Yaw Rate Sensor
      *g for No. 4 Junction Connector *h for No. 1 Junction Connector [Steering Bus]
      No. 2 Junction Connector Wiring Color Connect to
      L97-1 (CANH) R No. 3 junction connector
      L97-12 (CANL) G
      L97-2 (CANH) R Air conditioning amplifier assembly
      L97-13 (CANL) G
      L97-3 (CANH) R Multi-media module receiver assembly
      L97-14 (CANL) G
      L97-4 (CANH) R No. 1 junction connector [V bus]
      L97-15 (CANL) G
      L97-9 (CANH) B Yaw rate sensor
      L97-20 (CANL) W
      L97-10 (CANH) B No. 4 junction connector
      L97-21 (CANL) W
      L97-11 (CANH) B No. 1 junction connector [Steering bus]
      L97-22 (CANL) W

    3. NO. 3 JUNCTION CONNECTOR

      A01GLQAE92
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 3 Junction Connector)

      		 *b for Skid Control ECU Assembly
      *c for No. 1 Meter ECU Sub-assembly *d for No. 2 Junction Connector
      *e for Center Airbag Sensor Assembly *f for Main Body ECU (Driver Side Junction Block)
      *g for DLC3 *h for Headlight Swivel ECU Assembly
      No. 3 Junction Connector Wiring Color Connect to
      L98-5 (CANH) R Skid control ECU assembly
      L98-16 (CANL) G
      L98-6 (CANH) R No. 1 meter ECU sub-assembly
      L98-17 (CANL) G
      L98-7 (CANH) R No. 2 junction connector
      L98-18 (CANL) G
      L98-8 (CANH) R Center airbag sensor assembly
      L98-19 (CANL) G
      L98-9 (CANH) R Main body ECU (driver side junction block)
      L98-20 (CANL) G
      L98-10 (CANH) R DLC3
      L98-21 (CANL) G
      L98-11 (CANH) R Headlight swivel ECU assembly
      L98-22 (CANL) G

    4. NO. 4 JUNCTION CONNECTOR

      A01GLQAE67
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 4 Junction Connector)

      		 *b for No. 5 Junction Connector
      *c for No. 2 Junction Connector *d for Seat Belt Control ECU (w/ Pre-crash Safety System)
      *e for Blind Spot Monitor Sensor LH (w/ Blind Spot Monitor System) *f for Parking Brake ECU Assembly
      *g for No. 6 Junction Connector - -
      No. 4 Junction Connector Wiring Color Connect to
      S58-1 (CANH) B No. 5 junction connector
      S58-12 (CANL) W
      S58-2 (CANH) B No. 2 junction connector
      S58-13 (CANL) W
      S58-3 (CANH) B Seat belt control ECU*1
      S58-14 (CANL) W
      S58-8 (CANH) Y Blind spot monitor sensor LH*2
      S58-19 (CANL) B
      S58-10 (CANH) B Parking brake ECU assembly
      S58-21 (CANL) W
      S58-11 (CANH) B No. 6 junction connector
      S58-22 (CANL) W

      • *1: w/ Pre-crash Safety System

      • *2: w/ Blind Spot Monitor System

    5. NO. 5 JUNCTION CONNECTOR

      A01GLQAE93
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 5 Junction Connector)

      		 *b for Suspension Control ECU (w/ Air Suspension System)
      *c for Network Gateway ECU (w/ Pre-crash Intelligent Headrest) *d for No. 4 Junction Connector
      *e for Power Steering ECU Assembly *f for Skid Control ECU Assembly
      *g for Steering Angle Sensor - -
      No. 5 Junction Connector Wiring Color Connect to
      L99-1 (CANH) B Suspension control ECU*1
      L99-12 (CANL) W
      L99-2 (CANH) B Network gateway ECU*2
      L99-13 (CANL) W
      L99-3 (CANH) B No. 4 junction connector
      L99-14 (CANL) W
      L99-4 (CANH) B Power steering ECU assembly
      L99-15 (CANL) W
      L99-5 (CANH) B Skid control ECU assembly
      L99-16 (CANL) W
      L99-6 (CANH) R Steering angle sensor
      L99-17 (CANL) W

      • *1: w/ Air Suspension System

      • *2: w/ Pre-crash Intelligent Headrest

    6. NO. 6 JUNCTION CONNECTOR

      A01GLQAE94
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 6 Junction Connector)

      		 *b for Clearance Warning ECU Assembly
      *c for No. 4 Junction Connector *d for No. 7 Junction Connector
      *e for Steering Control ECU (w/ Variable Gear Ratio Steering System) *f for ECM
      *g for Driving Support ECU Assembly (w/ Pre-crash Safety System) - -
      No. 6 Junction Connector Wiring Color Connect to
      A65-6 (CANH) B Clearance warning ECU assembly
      A65-17 (CANL) W
      A65-7 (CANH) B No. 4 junction connector
      A65-18 (CANL) W
      A65-8 (CANH) B No. 7 junction connector
      A65-19 (CANL) W
      A65-9 (CANH) B Steering control ECU*1
      A65-20 (CANL) W
      A65-10 (CANH) L ECM
      A65-21 (CANL) LG
      A65-11 (CANH) B Driving support ECU assembly*2
      A65-22 (CANL) W

      • *1: w/ Variable Gear Ratio Steering System

      • *2: w/ Pre-crash Safety System

    7. NO. 7 JUNCTION CONNECTOR

      A01GLQAE95
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 7 Junction Connector)

      		 *b for Power Steering ECU Assembly
      *c for Skid Control ECU Assembly *d for Suspension Control ECU (w/ Air Suspension System)
      *e for No. 6 Junction Connector - -
      No. 7 Junction Connector Wiring Color Connect to
      A66-1 (CANH) V Power steering ECU assembly
      A66-12 (CANL) P
      A66-2 (CANH) B Skid control ECU assembly
      A66-13 (CANL) W
      A66-3 (CANH) B Suspension control ECU*
      A66-14 (CANL) W
      A66-4 (CANH) B No. 6 junction connector
      A66-15 (CANL) W

      • *: w/ Air Suspension System

    8. NO. 8 JUNCTION CONNECTOR

      A01GM1EE03
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 8 Junction Connector)

      		 *b for Front Multiplex Network Light ECU (Front Controller)
      *c for No. 9 Junction Connector *d for Front Power Seat Switch RH
      No. 8 Junction Connector Wiring Color Connect to
      R65-1 (CANH) B Front multiplex network light ECU (front controller)
      R65-3 (CANL) W
      R65-5 (CANH) B No. 9 junction connector
      R65-7 (CANL) W
      R65-6 (CANH) R Front power seat switch RH
      R65-8 (CANL) W

    9. NO. 9 JUNCTION CONNECTOR

      A01GLQAE72
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 9 Junction Connector)

      		 *b for Front Multiplex Network Door ECU RH
      *c for Rear Multiplex Network Door ECU RH *d for No. 8 Junction Connector
      *e for No. 10 Junction Connector - -
      No. 9 Junction Connector Wiring Color Connect to
      R48-1 (CANH) R Front multiplex network door ECU RH
      R48-12 (CANL) W
      R48-2 (CANH) R Rear multiplex network door ECU RH
      R48-13 (CANL) W
      R48-3 (CANH) B No. 8 junction connector
      R48-14 (CANL) W
      R48-4 (CANH) B No. 10 junction connector
      R48-15 (CANL) W

    10. NO. 10 JUNCTION CONNECTOR

      A01GLQAE99
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 10 Junction Connector)

      		 *b for Main Body ECU (Driver Side Junction Block)
      *c for No. 11 Junction Connector *d for Certification ECU (Smart Key ECU Assembly)
      *e for Multiplex Tilt and Telescopic ECU *f for No. 1 Meter ECU Sub-assembly
      *g for Windshield Wiper Switch Assembly *h for Steering Pad Switch Assembly (Steering Pad ECU)
      *i for Outer Mirror Switch Assembly *j for No. 9 Junction Connector
      No. 10 Junction Connector Wiring Color Connect to
      L95-3 (CANH) B Main body ECU (driver side junction block)
      L95-14 (CANL) W
      L95-4 (CANH) B No. 11 junction connector
      L95-15 (CANL) W
      L95-5 (CANH) B Certification ECU (smart key ECU assembly)
      L95-16 (CANL) W
      L95-6 (CANH) B Multiplex tilt and telescopic ECU
      L95-17 (CANL) W
      L95-7 (CANH) B No. 1 meter ECU sub-assembly
      L95-18 (CANL) W
      L95-8 (CANH) R Windshield wiper switch assembly
      L95-19 (CANL) W
      L95-9 (CANH) R Steering pad switch assembly (steering pad ECU)
      L95-20 (CANL) W
      L95-10 (CANH) B Outer mirror switch assembly
      L95-21 (CANL) W
      L95-11 (CANH) B No. 9 junction connector
      L95-22 (CANL) W

    11. NO. 11 JUNCTION CONNECTOR

      A01GLQAE97
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 11 Junction Connector)

      		 *b for Front Power Seat Switch LH
      *c for No. 12 Junction Connector *d for Rear Multiplex Network Door ECU LH
      *e for Front Multiplex Network Door ECU LH *f for No. 10 Junction Connector
      *g for Driving Support ECU Assembly (w/ Pre-crash Safety System) *h for Tire Pressure Warning Receiver Assembly (w/ Tire Pressure Warning System)
      No. 11 Junction Connector Wiring Color Connect to
      S92-1 (CANH) R Front power seat switch LH
      S92-12 (CANL) W
      S92-2 (CANH) B No. 12 junction connector
      S92-13 (CANL) W
      S92-3 (CANH) R Rear multiplex network door ECU LH
      S92-14 (CANL) W
      S92-4 (CANH) R Front multiplex network door ECU LH
      S92-15 (CANL) W
      S92-5 (CANH) B No. 10 junction connector
      S92-16 (CANL) W
      S92-6 (CANH) B Driving support ECU assembly*1
      S92-17 (CANL) W
      S92-7 (CANH) B Tire pressure warning receiver assembly*2
      S92-18 (CANL) W

      • *1: w/ Pre-crash Safety System

      • *2: w/ Tire Pressure Warning System

    12. NO. 12 JUNCTION CONNECTOR

      A01GLQAE75
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 12 Junction Connector)

      		 *b for Rear Power Seat Switch
      *c for Power Trunk Lid Control ECU (Luggage Closer Motor Assembly) *d for Luggage Room Junction Block Assembly (Rear Junction Block ECU)
      *e for No. 11 Junction Connector - -
      No. 12 Junction Connector Wiring Color Connect to
      S59-1 (CANH) B Rear power seat switch
      S59-12 (CANL) W
      S59-2 (CANH) B Power trunk lid control ECU (luggage closer motor assembly)
      S59-13 (CANL) W
      S59-3 (CANH) B Luggage room junction block assembly (rear junction block ECU)
      S59-14 (CANL) W
      S59-4 (CANH) B No. 11 junction connector
      S59-15 (CANL) W

    13. NO. 13 JUNCTION CONNECTOR (w/ Pre-crash Safety System)

      A01GLQAE89
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 13 Junction Connector)

      		 *b for Network Gateway ECU (w/ Pre-crash Intelligent Headrest)
      *c for Active Headrest Control ECU LH (Front Seat Headrest Assembly LH) (w/ Pre-crash Intelligent Headrest) *d for Active Headrest Control ECU RH (Front Seat Headrest Assembly RH) (w/ Pre-crash Intelligent Headrest)
      *e for Driving Support ECU Assembly *f for Millimeter Wave Radar Sensor Assembly
      *g for Driver Monitor ECU Assembly (w/ Driver Monitor Camera) *h for No. 14 Junction Connector
      No. 13 Junction Connector Wiring Color Connect to
      L96-1 (CANH) R Network gateway ECU*1
      L96-12 (CANL) G
      L96-2 (CANH) R Active headrest control ECU LH (front seat headrest assembly LH)*1
      L96-13 (CANL) G
      L96-3 (CANH) R Active headrest control ECU RH (front seat headrest assembly RH)*1
      L96-14 (CANL) G
      L96-8 (CANH) B Driving support ECU assembly
      L96-19 (CANL) W
      L96-9 (CANH) B Millimeter waver radar sensor assembly
      L96-20 (CANL) W
      L96-10 (CANH) B Driver monitor ECU assembly*2
      L96-21 (CANL) W
      L96-11 (CANH) B No. 14 junction connector
      L96-22 (CANL) W

      • *1: w/ Pre-crash Intelligent Headrest

      • *2: w/ Driver Monitor Camera

    14. NO. 14 JUNCTION CONNECTOR (w/ Pre-crash Safety System)

      A01GHKUE01
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 14 Junction Connector)

      		 *b for Rear Millimeter Wave Radar Sensor Assembly (w/ Pre-crash Intelligent Headrest)
      *c for Object Recognition ECU (w/ Lane-keeping Assist System) *d for No. 13 Junction Connector
      *e for No. 1 Night View ECU (w/ Night View System) *f for No. 15 Junction Connector
      No. 14 Junction Connector Wiring Color Connect to
      R93-1 (CANH) B Rear millimeter wave radar sensor assembly*1
      R93-12 (CANL) W
      R93-2 (CANH) B Object recognition ECU*2
      R93-13 (CANL) W
      R93-3 (CANH) B No. 13 junction connector
      R93-14 (CANL) W
      R93-4 (CANH) B No. 1 night view ECU*3
      R93-15 (CANL) W
      R93-5 (CANH) B No. 15 junction connector
      R93-16 (CANL) W

      • *1: w/ Pre-crash Intelligent Headrest

      • *2: w/ Lane-keeping Assist System

      • *3: w/ Night View System

    15. A01GMQWE53
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 15 Junction Connector)
      *b for No. 14 Junction Connector

      NO. 15 JUNCTION CONNECTOR (w/ Pre-crash Safety System)

      No. 15 Junction Connector Wiring Color Connect to
      R94-2 (CANL) W No. 14 junction connector
      R94-3 (CANH) B

  3. CHECK DLC3


    1. A01GNP2E23

      Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and CAN branch wire.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note


      • After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

      • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      L31-6 (CANH) - L31-14 (CANL) R - G Engine switch off 54 to 69 Ω
      L31-6 (CANH) - L31-4 (CG) R - W-B Engine switch off 200 Ω or higher
      L31-14 (CANL) - L31-4 (CG) G - W-B Engine switch off 200 Ω or higher
      L31-6 (CANH) - L31-16 (BAT) R - B Engine switch off 6 kΩ or higher
      L31-14 (CANL) - L31-16 (BAT) G - B Engine switch off 6 kΩ or higher

  4. CHECK ECM

    A01GL0NE08
    Text in Illustration
    *A V Bus *B Steering Bus
    *C Braking and Driving Bus *D Powertrain Bus

    1. Disconnect the ECM connectors.

    2. Measure the resistance according to the value(s) in the table below.

      V Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      A13-14 (CANH) - A13-13 (CANL) R - G Engine switch off 108 to 132 Ω
      A13-14 (CANH) - E3-1 (E1) R - W-B Engine switch off 200 Ω or higher
      A13-13 (CANL) - E3-1 (E1) G - W-B Engine switch off 200 Ω or higher
      A13-14 (CANH) - A14-7 (BATT) R - B Engine switch off 6 kΩ or higher
      A13-13 (CANL) - A14-7 (BATT) G - B Engine switch off 6 kΩ or higher
      Steering Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      A13-12 (CA1H) - A13-11 (CA1L) B - W Engine switch off 108 to 132 Ω
      A13-12 (CA1H) - E3-1 (E1) B - W-B Engine switch off 200 Ω or higher
      A13-11 (CA1L) - E3-1 (E1) W - W-B Engine switch off 200 Ω or higher
      A13-12 (CA1H) - A14-7 (BATT) B - B Engine switch off 6 kΩ or higher
      A13-11 (CA1L) - A14-7 (BATT) W - B Engine switch off 6 kΩ or higher
      Braking and Driving Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      A13-18 (CA2H) - A13-17 (CA2L) L - LG Engine switch off 54 to 69 Ω
      A13-18 (CA2H) - E3-1 (E1) L - W-B Engine switch off 200 Ω or higher
      A13-17 (CA2L) - E3-1 (E1) LG - W-B Engine switch off 200 Ω or higher
      A13-18 (CA2H) - A14-7 (BATT) L - B Engine switch off 6 kΩ or higher
      A13-17 (CA2L) - A14-7 (BATT) LG - B Engine switch off 6 kΩ or higher
      Powertrain Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      A13-10 (CAN+) - A13-9 (CAN-) B - W Engine switch off 108 to 132 Ω
      A13-10 (CAN+) - E3-1 (E1) B - W-B Engine switch off 200 Ω or higher
      A13-9 (CAN-) - E3-1 (E1) W - W-B Engine switch off 200 Ω or higher
      A13-10 (CAN+) - A14-7 (BATT) B - B Engine switch off 6 kΩ or higher
      A13-9 (CAN-) - A14-7 (BATT) W - B Engine switch off 6 kΩ or higher

  5. CHECK SKID CONTROL ECU ASSEMBLY

    A01GNCJE06
    Text in Illustration
    *A V Bus *B Steering Bus
    *C Braking and Driving Bus - -

    1. Disconnect the skid control ECU assembly connectors.

    2. Measure the resistance according to the value(s) in the table below.

      V Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      A21-9 (CANH) - A21-8 (CANL) R - G Engine switch off 54 to 69 Ω
      A21-9 (CANH) - A19-1 (GND) R - W-B Engine switch off 200 Ω or higher
      A21-8 (CANL) - A19-1 (GND) G - W-B Engine switch off 200 Ω or higher
      A21-9 (CANH) - A19-43 (+BI1) R - B Engine switch off 6 kΩ or higher
      A21-8 (CANL) - A19-43 (+BI1) G - B Engine switch off 6 kΩ or higher
      Steering Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      A21-30 (CA1H) - A21-29 (CA1L) B - W Engine switch off 54 to 69 Ω
      A21-30 (CA1H) - A19-1 (GND) B - W-B Engine switch off 200 Ω or higher
      A21-29 (CA1L) - A19-1 (GND) W - W-B Engine switch off 200 Ω or higher
      A21-30 (CA1H) - A19-43 (+BI1) B - B Engine switch off 6 kΩ or higher
      A21-29 (CA1L) - A19-43 (+BI1) W - B Engine switch off 6 kΩ or higher
      Braking and Driving Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      A19-7 (CA2H) - A19-6 (CA2L) B - W Engine switch off 54 to 69 Ω
      A19-7 (CA2H) - A19-1 (GND) B - W-B Engine switch off 200 Ω or higher
      A19-6 (CA2L) - A19-1 (GND) W - W-B Engine switch off 200 Ω or higher
      A19-7 (CA2H) - A19-43 (+BI1) B - B Engine switch off 6 kΩ or higher
      A19-6 (CA2L) - A19-43 (+BI1) W - B Engine switch off 6 kΩ or higher

  6. CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

    A01GJF6E04

    1. Disconnect the air conditioning amplifier assembly connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      L77-3 (CANH) - L77-4 (CANL) R - G Engine switch off 54 to 69 Ω
      L77-3 (CANH) - L76-1 (GND) R - W-B Engine switch off 200 Ω or higher
      L77-4 (CANL) - L76-1 (GND) G - W-B Engine switch off 200 Ω or higher
      L77-3 (CANH) - L76-6 (+B1) R - L Engine switch off 6 kΩ or higher
      L77-4 (CANL) - L76-6 (+B1) G - L Engine switch off 6 kΩ or higher

  7. CHECK MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK)

    A01GMXPE19
    Text in Illustration
    *A V Bus *B MS Bus

    1. Disconnect the main body ECU (driver side junction block) connectors.

    2. Measure the resistance according to the value(s) in the table below.

      V Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      L11-5 (CANH) - L11-6 (CANL) R - G Engine switch off 54 to 69 Ω
      L11-5 (CANH) - DA-40(GND1) R - W-B Engine switch off 200 Ω or higher
      L11-6 (CANL) - DA-40(GND1) G - W-B Engine switch off 200 Ω or higher
      L11-5 (CANH) - DF-1 (ALTB) R - B Engine switch off 6 kΩ or higher
      L11-6 (CANL) - DF-1 (ALTB) G - B Engine switch off 6 kΩ or higher
      MS Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      L11-16 (CANP) - L11-15 (CANN) B - W Engine switch off 54 to 69 Ω
      L11-16 (CANP) - DA-40(GND1) B - W-B Engine switch off 200 Ω or higher
      L11-15 (CANN) - DA-40(GND1) W - W-B Engine switch off 200 Ω or higher
      L11-16 (CANP) - DF-1 (ALTB) B - B Engine switch off 6 kΩ or higher
      L11-15 (CANN) - DF-1 (ALTB) W - B Engine switch off 6 kΩ or higher

  8. CHECK NO. 1 METER ECU SUB-ASSEMBLY

    A01GHK7E11
    Text in Illustration
    *A V Bus *B MS Bus

    1. Disconnect the No. 1 meter ECU sub-assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      V Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      L10-20 (CANH) - L10-21 (CANL) R - G Engine switch off 54 to 69 Ω
      L10-20 (CANH) - L10-18 (ES) R - BR Engine switch off 200 Ω or higher
      L10-21 (CANL) - L10-18 (ES) G - BR Engine switch off 200 Ω or higher
      L10-20 (CANH) - L10-13 (B) R - P Engine switch off 6 kΩ or higher
      L10-21 (CANL) - L10-13 (B) G - P Engine switch off 6 kΩ or higher
      MS Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      L10-22 (CANP) - L10-23 (CANN) B - W Engine switch off 54 to 69 Ω
      L10-22 (CANP) - L10-18 (ES) B - BR Engine switch off 200 Ω or higher
      L10-23 (CANN) - L10-18 (ES) W - BR Engine switch off 200 Ω or higher
      L10-22 (CANP) - L10-13 (B) B - P Engine switch off 6 kΩ or higher
      L10-23 (CANN) - L10-13 (B) W - P Engine switch off 6 kΩ or higher

  9. CHECK CENTER AIRBAG SENSOR ASSEMBLY

    A01GHMGE09

    1. Disconnect the center airbag sensor assembly connector Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      L73-13 (CANH) - L73-22 (CANL) R - G Engine switch off 108 to 132 Ω
      L73-13 (CANH) - L73-25 (E1) R - W-B Engine switch off 200 Ω or higher
      L73-22 (CANL) - L73-25 (E1) G - W-B Engine switch off 200 Ω or higher
      L73-13 (CANH) - L31-16 (BAT) R - B Engine switch off 6 kΩ or higher
      L73-22 (CANL) - L31-16 (BAT) G - B Engine switch off 6 kΩ or higher

  10. CHECK ELECTRIC POWER CONTROL ECU (PASSENGER SIDE JUNCTION BLOCK)

    A01GIU6E10

    1. Disconnect the electric power control ECU (passenger side junction block) connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      A69-15 (CANH) - A69-14 (CANL) R - G Engine switch off 54 to 69 Ω
      A69-15 (CANH) - PA-39 (GND) R - W-B Engine switch off 200 Ω or higher
      A69-14 (CANL) - PA-39 (GND) G - W-B Engine switch off 200 Ω or higher
      A69-15 (CANH) - PM-1 (BECU) R - L Engine switch off 6 kΩ or higher
      A69-14 (CANL) - PM-1 (BECU) G - L Engine switch off 6 kΩ or higher

  11. CHECK HEADLIGHT SWIVEL ECU ASSEMBLY

    A01GJ66E06

    1. Disconnect the headlight swivel ECU assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      A37-12 (CANH) - A37-13 (CANL) R - G Engine switch off 54 to 69 Ω
      A37-12 (CANH) - A37-22 (E1) R - W-B Engine switch off 200 Ω or higher
      A37-13 (CANL) - A37-22 (E1) G - W-B Engine switch off 200 Ω or higher
      A37-12 (CANH) - L31-16 (BAT) R - B Engine switch off 6 kΩ or higher
      A37-13 (CANL) - L31-16 (BAT) G - B Engine switch off 6 kΩ or higher

  12. CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY

    A01GJGWE05

    1. Disconnect the multi-media module receiver assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      L146-1 (CANH) - L146-2 (CANL) R - G Engine switch off 54 to 69 Ω
      L146-1 (CANH) - L146-12 (GND1) R - W-B Engine switch off 200 Ω or higher
      L146-2 (CANL) - L146-12 (GND1) G - W-B Engine switch off 200 Ω or higher
      L146-1 (CANH) - L146-17 (+B1) R - R Engine switch off 6 kΩ or higher
      L146-2 (CANL) - L146-17 (+B1) G - R Engine switch off 6 kΩ or higher

  13. CHECK STEERING ANGLE SENSOR

    A01GJ3YE03

    1. Disconnect the steering angle sensor connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      L21-10 (CANH) - L21-9 (CANL) R - W Engine switch off 54 to 69 Ω
      L21-10 (CANH) - L21-2 (ESS) R - W-B Engine switch off 200 Ω or higher
      L21-9 (CANL) - L21-2 (ESS) W - W-B Engine switch off 200 Ω or higher
      L21-10 (CANH) - L21-3 (BAT) R - R Engine switch off 6 kΩ or higher
      L21-9 (CANL) - L21-3 (BAT) W - R Engine switch off 6 kΩ or higher

  14. CHECK YAW RATE SENSOR

    A01GM6WE06

    1. Disconnect the yaw rate sensor connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      L71-3 (CANH) - L71-2 (CANL) B - W Engine switch off 54 to 69 Ω
      L71-3 (CANH) - L71-1 (GND) B - W-B Engine switch off 200 Ω or higher
      L71-2 (CANL) - L71-1 (GND) W - W-B Engine switch off 200 Ω or higher
      L71-3 (CANH) - L31-16 (BAT) B - B Engine switch off 6 kΩ or higher
      L71-2 (CANL) - L31-16 (BAT) W - B Engine switch off 6 kΩ or higher

  15. CHECK POWER STEERING ECU ASSEMBLY

    A01GIULE01
    Text in Illustration
    *A Steering Bus *B Braking and Driving Bus

    1. Disconnect the power steering ECU assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Steering Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      A44-2 (CA1H) - A44-3 (CA1L) L - LG Engine switch off 108 to 132 Ω
      A44-2 (CA1H) - A44-5 (PGND) L - W-B Engine switch off 200 Ω or higher
      A44-3 (CA1L) - A44-5 (PGND) LG - W-B Engine switch off 200 Ω or higher
      A44-2 (CA1H) - A44-6 (+B) L - R Engine switch off 6 kΩ or higher
      A44-3 (CA1L) - A44-6 (+B) LG - R Engine switch off 6 kΩ or higher
      Braking and Driving Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      A44-1 (CA2H) - A44-8 (CA2L) V - P Engine switch off 108 to 132 Ω
      A44-1 (CA2H) - A44-5 (PGND) V - W-B Engine switch off 200 Ω or higher
      A44-8 (CA2L) - A44-5 (PGND) P - W-B Engine switch off 200 Ω or higher
      A44-1 (CA2H) - A44-6 (+B) V - R Engine switch off 6 kΩ or higher
      A44-8 (CA2L) - A44-6 (+B) P - R Engine switch off 6 kΩ or higher

  16. CHECK STEERING CONTROL ECU (w/ Variable Gear Ratio Steering System)

    A01GMNDE01
    Text in Illustration
    *A Steering Bus *B Braking and Driving Bus

    1. Disconnect the steering control ECU connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Steering Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      A41-9 (CANH) - A41-20 (CANL) B - W Engine switch off 54 to 69 Ω
      A41-9 (CANH) - A42-7 (PGND) B - W-B Engine switch off 200 Ω or higher
      A41-20 (CANL) - A42-7 (PGND) W - W-B Engine switch off 200 Ω or higher
      A41-9 (CANH) - A42-10 (+BI) B - R Engine switch off 6 kΩ or higher
      A41-20 (CANL) - A42-10 (+BI) W - R Engine switch off 6 kΩ or higher
      Braking and Driving Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      A42-4 (CAN+) - A42-9 (CAN-) B - W Engine switch off 54 to 69 Ω
      A42-4 (CAN+) - A42-7 (PGND) B - W-B Engine switch off 200 Ω or higher
      A42-9 (CAN-) - A42-7 (PGND) W - W-B Engine switch off 200 Ω or higher
      A42-4 (CAN+) - A42-10 (+BI) B - R Engine switch off 6 kΩ or higher
      A42-9 (CAN-) - A42-10 (+BI) W - R Engine switch off 6 kΩ or higher

  17. CHECK SUSPENSION CONTROL ECU (w/ Air Suspension System)

    A01GHJAE01
    Text in Illustration
    *A Steering Bus *B Braking and Driving Bus

    1. Disconnect the suspension control ECU connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Steering Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      L88-7 (CANH) - L88-8 (CANL) B - W Engine switch off 54 to 69 Ω
      L88-7 (CANH) - L88-4 (GND) B - W-B Engine switch off 200 Ω or higher
      L88-8 (CANL) - L88-4 (GND) W - W-B Engine switch off 200 Ω or higher
      L88-7 (CANH) - L31-16 (BAT) B - B Engine switch off 6 kΩ or higher
      L88-8 (CANL) - L31-16 (BAT) W - B Engine switch off 6 kΩ or higher
      Braking and Driving Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      R1-22 (CA2H) - R1-21 (CA2L) B - W Engine switch off 54 to 69 Ω
      R1-22 (CA2H) - L88-4 (GND) B - W-B Engine switch off 200 Ω or higher
      R1-21 (CA2L) - L88-4 (GND) W - W-B Engine switch off 200 Ω or higher
      R1-22 (CA2H) - L31-16 (BAT) B - B Engine switch off 6 kΩ or higher
      R1-21 (CA2L) - L31-16 (BAT) W - B Engine switch off 6 kΩ or higher

  18. CHECK SEAT BELT CONTROL ECU (w/ Pre-crash Safety System)

    A01GNXCE11

    1. Disconnect the seat belt control ECU connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      S47-1 (CANH) - S47-2 (CANL) B - W Engine switch off 54 to 69 Ω
      S47-1 (CANH) - S45-8 (PGND) B - W-B Engine switch off 200 Ω or higher
      S47-2 (CANL) - S45-8 (PGND) W - W-B Engine switch off 200 Ω or higher
      S47-1 (CANH) - S45-7 (+B) B - B Engine switch off 6 kΩ or higher
      S47-2 (CANL) - S45-7 (+B) W - B Engine switch off 6 kΩ or higher

  19. CHECK DRIVING SUPPORT ECU ASSEMBLY (w/ Pre-crash Safety System)

    A01GJ3TE01
    Text in Illustration
    *A Steering Bus *B Braking and Driving Bus
    *C MS Bus *D Parking Assist Bus

    1. Disconnect the driving support ECU assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Steering Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      A33-1 (CA1H) - A33-2 (CA1L) B - W Engine switch off 54 to 69 Ω
      A33-1 (CA1H) - A33-25 (GND) B - W-B Engine switch off 200 Ω or higher
      A33-2 (CA1L) - A33-25 (GND) W - W-B Engine switch off 200 Ω or higher
      A33-1 (CA1H) - L31-16 (BAT) B - B Engine switch off 6 kΩ or higher
      A33-2 (CA1L) - L31-16 (BAT) W - B Engine switch off 6 kΩ or higher
      Braking and Driving Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      A33-16 (CA2H) - A33-17 (CA2L) B - W Engine switch off 54 to 69 Ω
      A33-16 (CA2H) - A33-25 (GND) B - W-B Engine switch off 200 Ω or higher
      A33-17 (CA2L) - A33-25 (GND) W - W-B Engine switch off 200 Ω or higher
      A33-16 (CA2H) - L31-16 (BAT) B - B Engine switch off 6 kΩ or higher
      A33-17 (CA2L) - L31-16 (BAT) W - B Engine switch off 6 kΩ or higher
      MS Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      A33-19 (CANP) - A33-18 (CANN) B - W Engine switch off 54 to 69 Ω
      A33-19 (CANP) - A33-25 (GND) B - W-B Engine switch off 200 Ω or higher
      A33-18 (CANN) - A33-25 (GND) W - W-B Engine switch off 200 Ω or higher
      A33-19 (CANP) - L31-16 (BAT) B - B Engine switch off 6 kΩ or higher
      A33-18 (CANN) - L31-16 (BAT) W - B Engine switch off 6 kΩ or higher
      Parking Assist Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      A33-40 (CA1P) - A33-39 (CA1N) B - W Engine switch off 54 to 69 Ω
      A33-40 (CA1P) - A33-25 (GND) B - W-B Engine switch off 200 Ω or higher
      A33-39 (CA1N) - A33-25 (GND) W - W-B Engine switch off 200 Ω or higher
      A33-40 (CA1P) - L31-16 (BAT) B - B Engine switch off 6 kΩ or higher
      A33-39 (CA1N) - L31-16 (BAT) W - B Engine switch off 6 kΩ or higher

  20. CHECK NETWORK GATEWAY ECU (w/ Pre-crash Intelligent Headrest)

    A01GMDUE01
    Text in Illustration
    *A Steering Bus *B WIL Bus

    1. Disconnect the network gateway ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Steering Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      L102-16 (CA1H) - L102-15 (CA1L) B - W Engine switch off 54 to 69 Ω
      L102-16 (CA1H) - L102-4 (GND) B - W-B Engine switch off 200 Ω or higher
      L102-15 (CA1L) - L102-4 (GND) W - W-B Engine switch off 200 Ω or higher
      L102-16 (CA1H) - L31-16 (BAT) B - B Engine switch off 6 kΩ or higher
      L102-15 (CA1L) - L31-16 (BAT) W - B Engine switch off 6 kΩ or higher
      WIL Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      L102-13 (CA2H) - L102-12 (CA2L) R - G Engine switch off 54 to 69 Ω
      L102-13 (CA2H) - L102-4 (GND) R - W-B Engine switch off 200 Ω or higher
      L102-12 (CA2L) - L102-4 (GND) G - W-B Engine switch off 200 Ω or higher
      L102-13 (CA2H) - L31-16 (BAT) R - B Engine switch off 6 kΩ or higher
      L102-12 (CA2L) - L31-16 (BAT) G - B Engine switch off 6 kΩ or higher

  21. CHECK PARKING BRAKE ECU ASSEMBLY

    A01GJHRE08

    1. Disconnect the parking brake ECU assembly connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      S48-9 (CA2H) - S48-1 (CA2L) B - W Engine switch off 108 to 132 Ω
      S48-9 (CA2H) - S46-3 (GND1) B - W-B Engine switch off 200 Ω or higher
      S48-1 (CA2L) - S46-3 (GND1) W - W-B Engine switch off 200 Ω or higher
      S48-9 (CA2H) - S48-2 (BECU) B - BE Engine switch off 6 kΩ or higher
      S48-1 (CA2L) - S48-2 (BECU) W - BE Engine switch off 6 kΩ or higher

  22. CHECK BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor System)

    A01GK9KE05
    Text in Illustration
    *A Braking and Driving Bus *B Sensor Bus

    1. Disconnect the blind spot monitor sensor LH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Braking and Driving Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      m2-2 (CA1P) - m2-7 (CA1N) Y - B Engine switch off 54 to 69 Ω
      m2-2 (CA1P) - m2-10 (BLGD) Y - W-B Engine switch off 200 Ω or higher
      m2-7 (CA1N) - m2-10 (BLGD) B - W-B Engine switch off 200 Ω or higher
      m2-2 (CA1P) - L31-16 (BAT) Y - B Engine switch off 6 kΩ or higher
      m2-7 (CA1N) - L31-16 (BAT) B - B Engine switch off 6 kΩ or higher
      Sensor Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      m2-1 (CA2P) - m2-6 (CA2N) B - Y Engine switch off 108 to 132 Ω
      m2-1 (CA2P) - m2-10 (BLGD) B - W-B Engine switch off 200 Ω or higher
      m2-6 (CA2N) - m2-10 (BLGD) Y - W-B Engine switch off 200 Ω or higher
      m2-1 (CA2P) - L31-16 (BAT) B - B Engine switch off 6 kΩ or higher
      m2-6 (CA2N) - L31-16 (BAT) Y - B Engine switch off 6 kΩ or higher

  23. CHECK BLIND SPOT MONITOR SENSOR RH (w/ Blind Spot Monitor System)

    A01GK9KE06

    1. Disconnect the blind spot monitor sensor RH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      m1-1 (CA2P) - m1-6 (CA2N) B - Y Engine switch off 108 to 132 Ω
      m1-1 (CA2P) - m1-10 (BRGD) B - W-B Engine switch off 200 Ω or higher
      m1-6 (CA2N) - m1-10 (BLGD) Y - W-B Engine switch off 200 Ω or higher
      m1-1 (CA2P) - L31-16 (BAT) B - B Engine switch off 6 kΩ or higher
      m1-6 (CA2N) - L31-16 (BAT) Y - B Engine switch off 6 kΩ or higher

  24. CHECK CLEARANCE WARNING ECU ASSEMBLY

    A01GKD1E06

    1. Disconnect the clearance warning ECU assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      L169-3 (CA2H) - L169-5 (CA2L) B - W Engine switch off 54 to 69 Ω
      L169-3 (CA2H) - L169-17 (E) B - W-B Engine switch off 200 Ω or higher
      L169-5 (CA2L) - L169-17 (E) W - W-B Engine switch off 200 Ω or higher
      L169-3 (CA2H) - L31-16 (BAT) B - B Engine switch off 6 kΩ or higher
      L169-5 (CA2L) - L31-16 (BAT) W - B Engine switch off 6 kΩ or higher

  25. CHECK FRONT MULTIPLEX NETWORK LIGHT ECU (FRONT CONTROLLER)

    A01GN13E10

    1. Disconnect the front multiplex network light ECU (front controller) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      A50-3 (CANP) - A50-4 (CANN) B - W Engine switch off 108 to 132 Ω
      A50-3 (CANP) - A50-2 (E) B - W-B Engine switch off 200 Ω or higher
      A50-4 (CANN) - A50-2 (E) W - W-B Engine switch off 200 Ω or higher
      A50-3 (CANP) - A50-1 (FMB3) B - LG Engine switch off 6 kΩ or higher
      A50-4 (CANN) - A50-1 (FMB3) W - LG Engine switch off 6 kΩ or higher

  26. CHECK OUTER MIRROR SWITCH ASSEMBLY

    A01GLNQE14

    1. Disconnect the outer mirror switch assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      L6-2 (CANP) - L6-3 (CANN) B - W Engine switch off 54 to 69 Ω
      L6-2 (CANP) - L6-1 (E) B - W-B Engine switch off 200 Ω or higher
      L6-3 (CANN) - L6-1 (E) W - W-B Engine switch off 200 Ω or higher
      L6-2 (CANP) - L6-12 (B) B - B Engine switch off 6 kΩ or higher
      L6-3 (CANN) - L6-12 (B) W - B Engine switch off 6 kΩ or higher

  27. CHECK STEERING PAD SWITCH ASSEMBLY (STEERING PAD ECU)

    Tech Tips

    As there is a spiral cable sub-assembly between the steering pad ECU and the vehicle harness connector, a direct inspection of the steering pad ECU side of the vehicle harness connector cannot be performed.

    A01GJ2QE03

    1. Disconnect the spiral cable sub-assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      L110-10 (CANP) - L110-9 (CANN) R - W Engine switch off 54 to 69 Ω
      L110-10 (CANP) - L110-3 (NOSB) R - W-B Engine switch off 200 Ω or higher
      L110-9 (CANN) - L110-3 (NOSB) W - W-B Engine switch off 200 Ω or higher
      L110-10 (CANP) - L110-7 (+B) R - B Engine switch off 6 kΩ or higher
      L110-9 (CANN) - L110-7 (+B) W - B Engine switch off 6 kΩ or higher

  28. CHECK MULTIPLEX TILT AND TELESCOPIC ECU

    A01GHULE07

    1. Disconnect the multiplex tilt and telescopic ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      L34-5 (CANP) - L34-14 (CANN) B - W Engine switch off 54 to 69 Ω
      L34-5 (CANP) - L34-11 (GND) B - W-B Engine switch off 200 Ω or higher
      L34-14 (CANN) - L34-11 (GND) W - W-B Engine switch off 200 Ω or higher
      L34-5 (CANP) - L34-2 (+B) B - B Engine switch off 6 kΩ or higher
      L34-14 (CANN) - L34-2 (+B) W - B Engine switch off 6 kΩ or higher

  29. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    A01GHTCE10

    1. Disconnect the certification ECU (smart key ECU assembly) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      L15-27 (CANH) - L15-28 (CANL) B - W Engine switch off 54 to 69 Ω
      L15-27 (CANH) - L15-17 (E) B - W-B Engine switch off 200 Ω or higher
      L15-28 (CANL) - L15-17 (E) W - W-B Engine switch off 200 Ω or higher
      L15-27 (CANH) - L15-1 (+B1) B - L Engine switch off 6 kΩ or higher
      L15-28 (CANL) - L15-1 (+B1) W - L Engine switch off 6 kΩ or higher

  30. CHECK FRONT MULTIPLEX NETWORK DOOR ECU RH

    A01GI5TE14

    1. Disconnect the front multiplex network door ECU RH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      N1-9 (CANP) - N1-10 (CANN) R - W Engine switch off 54 to 69 Ω
      N1-9 (CANP) - N1-1 (GND) R - W-B Engine switch off 200 Ω or higher
      N1-10 (CANN) - N1-1 (GND) W - W-B Engine switch off 200 Ω or higher
      N1-9 (CANP) - N1-11 (CPUB) R - R Engine switch off 6 kΩ or higher
      N1-10 (CANN) - N1-11 (CPUB) W - R Engine switch off 6 kΩ or higher

  31. CHECK FRONT MULTIPLEX NETWORK DOOR ECU LH

    A01GI5TE13

    1. Disconnect the front multiplex network door ECU LH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      N10-9 (CANP) - N10-10 (CANN) R - W Engine switch off 54 to 69 Ω
      N10-9 (CANP) - N10-1 (GND) R - W-B Engine switch off 200 Ω or higher
      N10-10 (CANN) - N10-1 (GND) W - W-B Engine switch off 200 Ω or higher
      N10-9 (CANP) - N10-11 (CPUB) R - R Engine switch off 6 kΩ or higher
      N10-10 (CANN) - N10-11 (CPUB) W - R Engine switch off 6 kΩ or higher

  32. CHECK REAR MULTIPLEX NETWORK DOOR ECU RH

    A01GKLWE02

    1. Disconnect the rear multiplex network door ECU RH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      O3-9 (CANP) - O3-10 (CANN) R - W Engine switch off 54 to 69 Ω
      O3-9 (CANP) - O3-1 (GND) R - W-B Engine switch off 200 Ω or higher
      O3-10 (CANN) - O3-1 (GND) W - W-B Engine switch off 200 Ω or higher
      O3-9 (CANP) - O3-11 (CPUB) R - R Engine switch off 6 kΩ or higher
      O3-10 (CANN) - O3-11 (CPUB) W - R Engine switch off 6 kΩ or higher

  33. CHECK REAR MULTIPLEX NETWORK DOOR ECU LH

    A01GKLWE01

    1. Disconnect the rear multiplex network door ECU LH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      O14-9 (CANP) - O14-10 (CANN) R - W Engine switch off 54 to 69 Ω
      O14-9 (CANP) - O14-1 (GND) R - W-B Engine switch off 200 Ω or higher
      O14-10 (CANN) - O14-1 (GND) W - W-B Engine switch off 200 Ω or higher
      O14-9 (CANP) - O14-11 (CPUB) R - R Engine switch off 6 kΩ or higher
      O14-10 (CANN) - O14-11 (CPUB) W - R Engine switch off 6 kΩ or higher

  34. CHECK FRONT POWER SEAT SWITCH RH

    A01GI05E09

    1. Disconnect the front power swat switch RH connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      e79-25 (CANP) - e79-24 (CANN) R - W Engine switch off 54 to 69 Ω
      e79-25 (CANP) - e78-6 (GND) R - W-B Engine switch off 200 Ω or higher
      e79-24 (CANN) - e78-6 (GND) W - W-B Engine switch off 200 Ω or higher
      e79-25 (CANP) - e78-7 (+B) R - B-R Engine switch off 6 kΩ or higher
      e79-24 (CANN) - e78-7 (+B) W - B-R Engine switch off 6 kΩ or higher

  35. CHECK FRONT POWER SEAT SWITCH LH

    A01GI05E10

    1. Disconnect the front power swat switch LH connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      e72-25 (CANP) - e72-24 (CANN) R - W Engine switch off 54 to 69 Ω
      e72-25 (CANP) - e71-6 (GND) R - W-B Engine switch off 200 Ω or higher
      e72-24 (CANN) - e71-6 (GND) W - W-B Engine switch off 200 Ω or higher
      e72-25 (CANP) - e71-7 (+B) R - B Engine switch off 6 kΩ or higher
      e72-24 (CANN) - e71-7 (+B) W - B Engine switch off 6 kΩ or higher

  36. CHECK REAR POWER SEAT SWITCH

    A01GI1QE01
    Text in Illustration
    *A for 4-Passenger with Ottoman *B except 4-Passenger with Ottoman

    1. Disconnect the rear power seat switch connector.

    2. Measure the resistance according to the value(s) in the table below.

      for 4-Passenger with Ottoman
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      S15-13 (CANH) - S15-14 (CANL) B - W Engine switch off 54 to 69 Ω
      S15-13 (CANH) - S15-1 (E) B - W-B Engine switch off 200 Ω or higher
      S15-14 (CANL) - S15-1 (E) W - W-B Engine switch off 200 Ω or higher
      S15-13 (CANH) - S15-8 (B) B - W Engine switch off 6 kΩ or higher
      S15-14 (CANN) - S15-8 (B) W - W Engine switch off 6 kΩ or higher
      except 4-Passenger with Ottoman
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      r2-5 (CANH) - r2-4 (CANL) R - W Engine switch off 54 to 69 Ω
      r2-5 (CANH) - r2-9 (E) R - W-B Engine switch off 200 Ω or higher
      r2-4 (CANL) - r2-9 (E) W - W-B Engine switch off 200 Ω or higher
      r2-5 (CANH) - r2-14 (B) R - W Engine switch off 6 kΩ or higher
      r2-4 (CANN) - r2-14 (B) W - W Engine switch off 6 kΩ or higher

  37. CHECK WINDSHIELD WIPER SWITCH ASSEMBLY

    A01GMFAE04

    1. Disconnect the windshield wiper switch assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      L25-5 (CANP) - L25-6 (CANN) R - W Engine switch off 54 to 69 Ω
      L25-5 (CANP) - L25-8 (E) R - W-B Engine switch off 200 Ω or higher
      L25-6 (CANN) - L25-8 (E) W - W-B Engine switch off 200 Ω or higher
      L25-5 (CANP) - L25-1 (B) R - B Engine switch off 6 kΩ or higher
      L25-6 (CANN) - L25-1 (B) W - B Engine switch off 6 kΩ or higher

  38. CHECK POWER TRUNK LID CONTROL ECU (LUGGAGE CLOSER MOTOR ASSEMBLY)

    A01GJ5WE03

    1. Disconnect the power trunk lid control ECU (luggage closer motor assembly) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      S43-6 (CANP) - S43-5 (CANN) B - W Engine switch off 54 to 69 Ω
      S43-6 (CANP) - S43-11 (GND) B - W-B Engine switch off 200 Ω or higher
      S43-5 (CANN) - S43-11 (GND) W - W-B Engine switch off 200 Ω or higher
      S43-6 (CANP) - S43-10 (ECUB) B - B Engine switch off 6 kΩ or higher
      S43-5 (CANN) - S43-10 (ECUB) W - B Engine switch off 6 kΩ or higher

  39. CHECK LUGGAGE ROOM JUNCTION BLOCK ASSEMBLY (REAR JUNCTION BLOCK ECU)

    A01GMXPE18

    1. Disconnect the luggage room junction block assembly (rear junction block ECU) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      S62-20 (CANP) - S62-28 (CANN) B - W Engine switch off 108 to 132 Ω
      S62-20 (CANP) - LA-43 (PGND) B - W-B Engine switch off 200 Ω or higher
      S62-28 (CANN) - LA-43 (PGND) W - W-B Engine switch off 200 Ω or higher
      S62-20 (CANP) - LD-4 (MPXB) B - R Engine switch off 6 kΩ or higher
      S62-28 (CANN) - LD-4 (MPXB) W - R Engine switch off 6 kΩ or higher

  40. CHECK TIRE PRESSURE WARNING RECEIVER ASSEMBLY (w/ Tire Pressure Warning System)

    A01GLL1E03

    1. Disconnect the tire pressure warning receiver assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      L101-3 (CANP) - L101-6 (CANN) B - W Engine switch off 54 to 69 Ω
      L101-3 (CANP) - L101-4 (GND) B - W-B Engine switch off 200 Ω or higher
      L101-6 (CANN) - L101-4 (GND) W - W-B Engine switch off 200 Ω or higher
      L101-3 (CANP) - L31-16 (BAT) B - B Engine switch off 6 kΩ or higher
      L101-6 (CANN) - L31-16 (BAT) W - B Engine switch off 6 kΩ or higher

  41. CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Pre-crash Safety System)

    A01GKVRE01

    1. Disconnect the millimeter wave radar sensor assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      B9-4 (CA1P) - B9-3 (CA1N) B - L Engine switch off 108 to 132 Ω
      B9-4 (CA1P) - L31-4 (CG) B - W-B Engine switch off 200 Ω or higher
      B9-3 (CA1N) - L31-4 (CG) L - W-B Engine switch off 200 Ω or higher
      B9-4 (CA1P) - L31-16 (BAT) B - B Engine switch off 6 kΩ or higher
      B9-3 (CA1N) - L31-16 (BAT) L - B Engine switch off 6 kΩ or higher

  42. CHECK REAR MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Pre-crash Intelligent Headrest)

    A01GKVRE02

    1. Disconnect the rear millimeter wave radar sensor assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      R51-4 (CA1P) - R51-3 (CA1N) B - W Engine switch off 108 to 132 Ω
      R51-4 (CA1P) - L31-4 (CG) B - W-B Engine switch off 200 Ω or higher
      R51-3 (CA1N) - L31-4 (CG) W - W-B Engine switch off 200 Ω or higher
      R51-4 (CA1P) - L31-16 (BAT) B - B Engine switch off 6 kΩ or higher
      R51-3 (CA1N) - L31-16 (BAT) W - B Engine switch off 6 kΩ or higher

  43. CHECK OBJECT RECOGNITION ECU (w/ Lane-keeping Assist System)

    A01GMJTE01

    1. Disconnect the object recognition ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      g1-16 (CANH) - g1-5 (CANL) B - W Engine switch off 54 to 69 Ω
      g1-16 (CANH) - g1-10 (GND) B - W-B Engine switch off 200 Ω or higher
      g1-5 (CANL) - g1-10 (GND) W - W-B Engine switch off 200 Ω or higher
      g1-16 (CANH) - L31-16 (BAT) B - B Engine switch off 6 kΩ or higher
      g1-5 (CANL) - L31-16 (BAT) W - B Engine switch off 6 kΩ or higher

  44. CHECK DRIVER MONITOR ECU ASSEMBLY (w/ Driver Monitor Camera)

    A01GNONE03

    1. Disconnect the driver monitor ECU assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      L140-12 (CANH) - L140-11 (CANL) B - W Engine switch off 54 to 69 Ω
      L140-12 (CANH) - L140-2 (GND) B - B Engine switch off 200 Ω or higher
      L140-11 (CANL) - L140-2 (GND) W - B Engine switch off 200 Ω or higher
      L140-12 (CANH) - L31-16 (BAT) B - B Engine switch off 6 kΩ or higher
      L140-11 (CANL) - L31-16 (BAT) W - B Engine switch off 6 kΩ or higher

  45. CHECK NO. 1 NIGHT VIEW ECU (w/ Night View System)

    A01GMGJE03

    1. Disconnect the No. 1 night view ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      g2-8 (CA1P) - g2-9 (CA1N) Y - L Engine switch off 54 to 69 Ω
      g2-8 (CA1P) - g2-6 (RE) Y - W-B Engine switch off 200 Ω or higher
      g2-9 (CA1N) - g2-6 (RE) L - W-B Engine switch off 200 Ω or higher
      g2-8 (CA1P) - L31-16 (BAT) Y - B Engine switch off 6 kΩ or higher
      g2-9 (CA1N) - L31-16 (BAT) L - B Engine switch off 6 kΩ or higher

  46. CHECK ACTIVE HEADREST CONTROL ECU RH (FRONT SEAT HEADREST ASSEMBLY RH) (w/ Pre-crash Intelligent Headrest)

    A01GK32E02

    1. Disconnect the active headrest control ECU RH (front seat headrest assembly RH) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      e60-2 (CA3H) - e60-5 (CA3L) R - G Engine switch off 108 to 132 Ω
      e60-2 (CA3H) - e60-1 (GND) R - W-B Engine switch off 200 Ω or higher
      e60-5 (CA3L) - e60-1 (GND) G - W-B Engine switch off 200 Ω or higher
      e60-2 (CA3H) - L31-16 (BAT) R - B Engine switch off 6 kΩ or higher
      e60-5 (CA3L) - L31-16 (BAT) G - B Engine switch off 6 kΩ or higher

  47. CHECK ACTIVE HEADREST CONTROL ECU LH (FRONT SEAT HEADREST ASSEMBLY LH) (w/ Pre-crash Intelligent Headrest)

    A01GK32E01

    1. Disconnect the active headrest control ECU LH (front seat headrest assembly LH) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      e73-2 (CA3H) - e73-5 (CA3L) R - G Engine switch off 108 to 132 Ω
      e73-2 (CA3H) - e73-1 (GND) R - W-B Engine switch off 200 Ω or higher
      e73-5 (CA3L) - e73-1 (GND) G - W-B Engine switch off 200 Ω or higher
      e73-2 (CA3H) - L31-16 (BAT) R - B Engine switch off 6 kΩ or higher
      e73-5 (CA3L) - L31-16 (BAT) G - B Engine switch off 6 kΩ or higher

  48. CHECK TCM

    A01GMLDE14

    1. Disconnect the TCM connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      A12-18 (CAN+) - A12-28 (CAN-) B - W Engine switch off 108 to 132 Ω
      A12-18 (CAN+) - E5-7 (E1) B - BR Engine switch off 200 Ω or higher
      A12-28 (CAN-) - E5-7 (E1) W - BR Engine switch off 200 Ω or higher
      A12-18 (CAN+) - A12-7 (BATT) B - R Engine switch off 6 kΩ or higher
      A12-28 (CAN-) - A12-7 (BATT) W - R Engine switch off 6 kΩ or higher