STEERING COLUMN ASSEMBLY (w/o VGRS) REMOVAL

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing the steering column Click here.

Tech Tips


  • Use the same procedures for the RHD and LHD.

  • The procedures listed below are for the LHD.


  1. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

  2. REMOVE COWL TOP VENTILATOR LOUVER


    1. A01GM4S

      for LHD:

      Remove the 6 clips and cowl top ventilator louver RH.

    2. A01GI9P

      for RHD:

      Remove the 6 clips and cowl top ventilator louver LH.

  3. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


    1. Disable the AUTO TILT AWAY function by changing the customize parameter Click here.

      Note

      Record the current customize parameter setting (whether the AUTO TILT AWAY function is enabled or disabled) in order to restore the current setting after finishing the operation.

      Tech Tips

      Performing the above operation causes the AUTO TILT AWAY function to be disabled when the engine switch is turned off.

    2. Turn the engine switch on (IG). Operate the tilt and telescopic switch to fully extend and lower the steering column assembly.

    3. Turn the engine switch off and disconnect the cable from the negative battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  5. REMOVE STEERING WHEEL ASSEMBLY

    Click here

  6. REMOVE STEERING COLUMN COVER (w/o Driver Monitor Camera)


    1. A01GN19

      Remove the 3 screws.

    2. Detach the 2 claws to remove the steering column cover lower.

      Note

      Do not damage the tilt and telescopic switch.

    3. A01GI18

      Detach the 4 clips.

    4. Detach the claw to remove the steering column cover upper.

  7. REMOVE STEERING COLUMN COVER (w/ Driver Monitor Camera)


    1. A01GKGR

      Remove the 3 screws.

    2. Detach the 2 claws to remove the steering column cover lower.

      Note

      Do not damage the tilt and telescopic switch.

    3. A01GKHQ

      Detach the 4 clips.

    4. Detach the claw to remove the steering column cover upper.

    5. Disconnect the driver monitor connector.

  8. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY


    1. Disconnect the connectors from the turn signal switch with spiral cable.

    2. A01GK7P

      Using pliers, grip the claws of the clamp and remove the turn signal switch with spiral cable from the steering column.

  9. REMOVE NO. 1 LOWER INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

  10. REMOVE NO. 1 AIR DUCT SUB-ASSEMBLY


    1. Detach the 2 claws and remove the wiring harness protector.

    2. A01GI8Q

      Detach the bolt, and remove the 2 claws and air duct.

  11. REMOVE STEERING SLIDING WITH SHAFT YOKE SUB-ASSEMBLY


    1. A01GJFBE02
      Text in Illustration
      *a Front of the Vehicle

      Loosen bolt A and remove bolt B, then slide the steering sliding with shaft yoke.

      Note


      • Do not remove bolt A.

      • Do not separate the steering sliding with shaft yoke from the intermediate shaft.

    2. A01GHO5E04
      Text in Illustration
      *1 No. 2 steering intermediate shaft
      *2 Intermediate shaft
      *a Matchmark

      Put matchmarks on the steering sliding with shaft yoke, No. 2 steering intermediate shaft and intermediate shaft.

    3. Remove the bolt and the steering sliding with shaft yoke from the steering intermediate shaft.

    4. A01GKZRE03
      Text in Illustration
      *1 Steering sliding with shaft yoke
      *2 No. 2 steering intermediate shaft

      Separate the steering sliding with shaft yoke from the No. 2 steering intermediate shaft.

      Tech Tips

      Insert a screwdriver or equivalent into the yoke's hole. Hold down the intermediate shaft's claw and remove the intermediate shaft. If the claw is damaged, remove the claw. The intermediate shaft does not have to be replaced.

  12. REMOVE STEERING INTERMEDIATE SHAFT


    1. A01GLDLE02
      Text in Illustration
      *a Matchmark

      Put matchmarks on the steering intermediate shaft and power steering link.

    2. Remove the bolt and steering intermediate shaft.

  13. REMOVE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY


    1. A01GKDGE02
      Text in Illustration
      *a Matchmark

      Put matchmarks on the No. 2 steering intermediate shaft and the steering column.

    2. Remove the bolt.

    3. A01GHOW

      Remove the clamp and No. 2 steering intermediate shaft.

  14. REMOVE STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR)


    1. Disconnect the connectors and wire harness clamps from the steering column.

    2. A01GHZ1

      Remove the 4 nuts and steering column.