REAR SPEED SENSOR INSTALLATION

Tech Tips


  • The procedures listed below are for the RH side.

  • Other than areas where instructions are provided, use the same procedures for the LH side and RH side.

Note

While the battery is connected, even if the engine switch is off, the brake control system activates when the brake pedal is depressed or the door courtesy switch turns on. Therefore during servicing of the brake system components, do not operate the brake pedal and open/close the doors while the battery is connected.


  1. INSTALL REAR SPEED SENSOR RH


    1. A01GLB8

      Install the sensor with the bolt.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Note


      • The rear speed sensor is easily damaged. When installing the rear speed sensor to the rear axle hub RH, do not use excessive force to rotate and install it.

      • Prevent foreign matter from attaching to the sensor tip.

      • Do not drop the sensor. If the sensor has been dropped, replace the sensor with a new one.

  2. INSTALL SKID CONTROL SENSOR WIRE


    1. A01GN33

      Connect the connector to the rear speed sensor.

    2. Install the sensor clamp with the bolt.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Note

      Do not twist the sensor wire when installing the clamps.

    3. Connect the pad wear indicator connector.

    4. A01GIXVE04

      Install the sensor clamp with the nut.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      Note

      Do not twist the sensor wire when installing the clamps.

    5. Except for coil spring type suspension:


      1. Install the sensor clamp (labeled A) with the nut (labeled B).

        Torque:
        5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      2. Connect the rear height control sensor connector (labeled C).

    6. A01GN9L

      Insert the connector and grommet to the inside of the vehicle through the hole in the wheel house.

    7. for LH:


      1. A01GMGB

        Install the No. 1 skid control sensor clamp with the nut.

        Torque:
        8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

      2. Attach the skid control sensor wire.

      3. Connect the rear speed sensor wire connector.

    8. for RH:


      1. A01GLZW

        Connect the rear speed sensor wire connector.

  3. INSTALL REAR WHEEL

    Torque:
    140 N*m  { 1428 kgf*cm, 103 ft.*lbf }

  4. INSTALL LUGGAGE COMPARTMENT TRIM COVER ASSEMBLY RH

    Click here

  5. INSTALL LUGGAGE COMPARTMENT TRIM COVER ASSEMBLY LH

    Click here

  6. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  7. INSTALL COWL TOP VENTILATOR LOUVER


    1. A01GM4S

      for LHD:

      Install the 6 clips and cowl top ventilator louver RH.

      Note

      If the cowl top ventilator louver RH is not properly installed, water may leak into the engine room and cause malfunctions. Therefore, make sure the cowl top ventilator louver RH is installed properly.

    2. A01GI9P

      for RHD:

      Install the 6 clips and cowl top ventilator louver LH.

      Note

      If the cowl top ventilator louver LH is not properly installed, water may leak into the engine room and cause malfunctions. Therefore, make sure the cowl top ventilator louver LH is installed properly.

  8. CHECK SPEED SENSOR SIGNAL

    Click here