GENERATOR INSTALLATION


  1. INSTALL GENERATOR ASSEMBLY

    A01GHPM

    1. Using an E8 "TORX" socket wrench, set the generator with the 2 stud bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }
    2. A01GLG5

      Install the generator with the 2 bolts and 2 nuts.

      Torque:
      43 N*m  { 438 kgf*cm, 32 ft.*lbf }
    3. A01GN07

      Connect the generator connector.

    4. Connect the harness to the +B terminal with the nut.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

  2. INSTALL V-RIBBED BELT


    1. A01GMNLE01

      Install the V belt as shown in the illustration.

      Note

      Check that the drive belt is properly set to each pulley.


      1. Rotate the tensioner pulley counterclockwise, and then remove the fix bar.

  3. INSTALL INTAKE AIR CONNECTOR PIPE


    1. Align the protrusion of the intake air resonator with the cutout of the bracket and insert the protrusion.

    2. Install the intake air connector pipe with the 3 hose clamps.

      Torque:
      for intake air connector pipe and throttle body
      4.8 N*m  { 49 kgf*cm, 42 in.*lbf }
      for intake air connector pipe and air cleaner cap
      3.8 N*m  { 39 kgf*cm, 34 in.*lbf }

      Tech Tips


      • Insert the protrusion of the intake air connector pipe into the hole of the hose clamp.

      • The intake air connector pipe and throttle body clamp can be tightened within the range of 4.0 N*m (41 kgf*cm, 35 in.*lbf) to 5.5 N*m (56 kgf*cm, 49 in.*lbf), and the intake air connector pipe and air cleaner cap clamp can be tightened within the range of 2.0 N*m (20 kgf*cm, 18 in.*lbf) to 5.5 N*m (56 kgf*cm, 49 in.*lbf).

    3. Attach the 2 wire harness clamps.

    4. A01GMMEE03

      Connect the No. 1 and No. 2 ventilation hoses to the intake air connector pipe.

      Tech Tips


      • Position the claws of the clamps as shown in the illustration.

      • Install the clamps so that they are within the hose's paint marks.

  4. INSTALL NO. 2 ENGINE UNDER COVER


    1. A01GNYRE01

      Install the No. 2 engine under cover with the 8 bolts.

      Torque:
      for Bolt A
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }
      for Bolt B
      27 N*m  { 275 kgf*cm, 20 ft.*lbf }

  5. INSTALL FRONT SUSPENSION MEMBER PROTECTOR LOWER


    1. Install the front suspension member protector lower with the 8 bolts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

  6. INSTALL NO. 1 ENGINE UNDER COVER


    1. Install the No. 1 engine under cover with the 13 screws and 7 clips.

  7. INSTALL NO. 1 AIR CLEANER INLET

    A01GME8E01

    1. Align the holes with the connection areas labeled A, and attach the No. 1 air cleaner inlet.

    2. A01GM3N

      Install the No. 1 air cleaner inlet with the 2 bolts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

  8. INSTALL AIR CLEANER INLET COVER SUB-ASSEMBLY

    A01GNHGE01

    1. Attach the 4 clips B.

      Note


      • Make sure the clips are attached securely.

      • Attaching the clips forcefully or hitting the top of the clips may damage them.

    2. Install the air cleaner inlet cover sub-assembly with the 5 clips labeled A.

  9. INSTALL V-BANK COVER SUB-ASSEMBLY

    A01GLQ5E01

    1. After sliding the cover from the vehicle front to the rear to attaching the 2 clips labeled A, attach the 4 clips labeled B and install the V-bank cover sub-assembly.

      Note


      • Make sure the clips are attached securely.

      • Attaching the clips forcefully or hitting the top of the clips may damage them.

  10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  11. INSTALL COWL TOP VENTILATOR LOUVER RH


    1. A01GM4S

      Install the 6 clips and cowl top ventilator louver RH.

      Note

      If the cowl top ventilator louver RH is not properly installed, water may leak into the engine room and cause malfunctions. Therefore, make sure the cowl top ventilator louver RH is installed properly.