IGNITION COIL AND SPARK PLUG REMOVAL


  1. REMOVE COWL TOP VENTILATOR LOUVER RH

    A01GM4S

    1. Remove the 6 clips and cowl top ventilator louver RH.

  2. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE V-BANK COVER SUB-ASSEMBLY

    A01GLQ5E01

    1. While using both hands, lift the rear side of the cover upwards to detach the 4 clips B. Slide the cover towards the front of the vehicle to detach the 2 clips labeled A, and remove the V-bank cover sub-assembly.

      Note

      The V-bank cover sub-assembly may be damaged if its front and rear are lifted at the same time.

  5. REMOVE AIR CLEANER INLET COVER SUB-ASSEMBLY

    A01GNHGE01

    1. Remove the 5 clips labeled A.

    2. Lift up the air cleaner inlet cover sub-assembly to detach the 4 clips labeled B, and remove the air cleaner inlet cover sub-assembly.

  6. REMOVE ENGINE ROOM SIDE COVER LH


    1. A01GKBH

      Remove the 5 clips and engine room side cover LH.

  7. REMOVE ENGINE ROOM SIDE COVER RH


    1. A01GLUY

      Remove the 5 clips and engine room side cover RH.

  8. REMOVE NO. 1 AIR CLEANER INLET

    A01GM3N

    1. Remove the 2 bolts.

    2. A01GMLIE01

      Hold the No. 1 air cleaner inlet by the protrusions labeled A and labeled B, and detach the connections.

    3. Rotate the No. 1 air cleaner inlet as shown in the illustration to detach the protrusion labeled C.

    4. Hold the air cleaner inlet by the protrusions labeled D and labeled E, and detach the connections.

    5. Rotate the No. 1 air cleaner inlet as shown in the illustration to detach the protrusion labeled F.

  9. REMOVE INTAKE AIR CONNECTOR PIPE


    1. A01GNDS

      Disconnect the No. 1 and No. 2 ventilation hoses from the intake air connector pipe.

    2. Using a clip remover, detach the 2 wire harness clamps.

    3. Loosen the 3 hose clamps, and remove the intake air connector pipe.

  10. REMOVE BATTERY


    1. Disconnect the positive (+) battery cable from the battery terminal.

    2. A01GIXL

      Disconnect the battery cable clamp.

    3. Remove the nut, battery clamp and No. 2 battery clamp bolt.

    4. Remove the battery insulator.

    5. Remove the battery.

  11. REMOVE BATTERY TRAY


    1. A01GJ7N

      Remove the 3 bolts and battery tray.

  12. REMOVE SKID CONTROL ECU BRACKET

    Click here

  13. REMOVE AIR CLEANER ASSEMBLY LH


    1. A01GJIY

      Disconnect the mass air flow meter connector.

    2. Disconnect the 2 clamps and air cleaner cap LH.

    3. Remove the air cleaner element from air cleaner case LH.

    4. A01GJKZ

      Remove the 2 nuts, clip and air cleaner case LH.

  14. REMOVE AIR CLEANER ASSEMBLY RH


    1. A01GIMA

      Disconnect the mass air flow meter connector.

    2. Disconnect the 2 clamps and air cleaner cap RH.

    3. Remove the air cleaner element from air cleaner case RH.

    4. A01GM6U

      Remove the 2 nuts, clip and air cleaner case RH.

  15. REMOVE IGNITION COIL ASSEMBLY


    1. A01GMG1

      Disconnect the 8 ignition coil assembly connectors.

    2. Remove the 8 bolts.

    3. A01GNKFE01

      Using a screwdriver, pry at the cutouts to remove the 8 ignition coils assemblies together with the 8 spark plug tube gaskets.

      Note

      When removing the spark plug tube gaskets, do not damage the cylinder head cover.

      Tech Tips

      Tape the screwdriver tip before use.

  16. REMOVE SPARK PLUG


    1. A01GLTF

      Using a 16 mm plug wrench, remove the 8 spark plugs.