ДЕМПФЕР ПУЛЬСАЦИЙ ДАВЛЕНИЯ В ТОПЛИВНОЙ СИСТЕМЕ УСТАНОВКА


  1. INSTALL FUEL PRESSURE PULSATION DAMPER ASSEMBLY


    1. A01CDVEE03
      Text in Illustration
      *1 O-ring

      Apply a light coat of gasoline or spindle oil to new O-ring of the fuel pressure pulsation damper.

    2. A01CBLE

      Install the fuel pressure pulsation damper with the 2 bolts.

      Torque:
      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

      Note

      Make sure that the O-ring is not cracked or jammed before installing the damper.

  2. INSTALL FUEL TUBE SUB-ASSEMBLY


    1. A01CG60E26
      Text in Illustration
      *1 Retainer
      *2 O-ring
      *3 Nylon Tube
      *4 Fuel Tube Connector
      *5 Pipe

      Connect the fuel tube.

    2. Push the fuel tube connector until it makes a "click" sound.

    3. A01CDLR

      Install the No. 2 fuel pipe clamp.

    4. Install the fuel tube to the fuel hose clamp.

  3. INSTALL AIR CLEANER CAP SUB-ASSEMBLY WITH HOSE


    1. A01CDPJ

      Установите крышку воздушного фильтра в сборе со шлангом и зафиксируйте 2 зажима.

    2. A01CEYSE01
      Обозначения на рисунке
      *1 Хомут шланга воздушного фильтра № 1
      *2 Канавка
      *3 Выступ
      *4 95°

      Подсоедините шланг воздушного фильтра № 1 к корпусу дроссельной заслонки и расцепите замок хомута шланга воздушного фильтра № 1.

      Note


      • Совместите канавку шланга воздушного фильтра с выступом на корпусе дроссельной заслонки и установите шланг.

      • Убедитесь, что выступ шланга воздушного фильтра № 1 находится в диапазоне, обозначенном *4

    3. A01CD15

      Подсоедините 2 зажима жгутов проводов и разъем датчика массового расхода воздуха.

    4. A01CFO3

      Подсоедините вентиляционный шланг.

    5. A01CCLR

      Подсоедините продувочный шланг к электровакуумному клапану № 1 в сборе и шлангу воздушного фильтра.

    6. A01CEOK

      Подсоедините питающий шланг паров топлива к электровакуумному клапану № 1 в сборе.

    7. Подсоедините зажим жгута проводов и разъем электровакуумного клапана № 1.

  4. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  5. INSPECT FOR FUEL LEAK


    1. Check fuel pump operation.


      1. Connect the intelligent tester to the DLC3.

      2. Turn the engine switch on (IG) and turn the intelligent tester on.

        Note

        Do not start the engine.

      3. Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump / Speed.

      4. Check for pressure in the fuel inlet tube from the fuel line. Check that sounds of fuel flowing in the fuel tank can be heard. If no sounds can be heard, check the integration relay, fuel pump, ECM and wiring connectors.

    2. Inspect for fuel leaks.


      1. Check that there is no fuel leakage after performing maintenance anywhere on the fuel system. If there is a fuel leak, repair or replace parts if necessary.

    3. Turn the engine switch off.

    4. Disconnect the intelligent tester from the DLC3.