REAR AXLE HUB (for 2WD) INSTALLATION


  1. INSTALL REAR AXLE CARRIER SUB-ASSEMBLY


    1. A017GBY

      Temporarily install the rear axle carrier sub-assembly with the 2 bolts and the 2 nuts.

    2. A017DP6

      Install the rear axle carrier sub-assembly with the 2 bolts and the 2 nuts.

      Torque:
      290 N*m  { 2956 kgf*cm, 213 ft.*lbf }

  2. TEMPORARILY INSTALL REAR STRUT ROD ASSEMBLY


    1. A017CFSE01

      Check that the identification mark of the rear strut rod assembly is positioned on the inner side of the vehicle.

    2. Temporarily install the rear strut rod assembly with the 2 bolts and the 2 nuts.

      Note

      Since stopper nuts are used, temporarily tighten the bolts.

  3. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY


    1. A017DQI

      Install the parking brake assembly and the rear axle hub and bearing assembly with the 4 bolts.

      Torque:
      75 N*m  { 764 kgf*cm, 55 ft.*lbf }

      Note

      Do not twist the No. 3 parking brake cable assembly when installing it.

  4. INSPECT REAR AXLE HUB BEARING LOOSENESS


    1. A017EJZ

      Using a dial indicator, check for looseness near the center of the axle hub.

      Maximum looseness
      0 mm (0 in.)

      Note

      Ensure that the dial indicator is set perpendicular to the measurement surface.

      If the looseness exceeds the maximum, replace the rear axle hub and bearing assembly.

  5. INSPECT REAR AXLE HUB RUNOUT


    1. A017FBT

      Using a dial indicator, check for runout on the surface of the axle hub outside the hub bolt.

      Maximum runout
      0.08 mm (0.0031 in.)

      Note

      Ensure that the dial indicator is set perpendicular to the measurement surface.

      If the runout exceeds the maximum, replace the rear axle hub and bearing assembly.

  6. INSTALL REAR SPEED SENSOR WIRE


    1. A017FKF

      Connect the connector to the rear speed sensor.

  7. INSTALL REAR DISC


    1. A017FKWE01

      Align matchmarks and install the rear disc.

      Note

      When replacing the rear disc with a new one, select the installation position where the rear disc has minimal runout.

  8. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY


    1. A017FLR

      Install the rear disc brake caliper assembly with the 2 bolts.

      Torque:
      78 N*m  { 795 kgf*cm, 57 ft.*lbf }

  9. INSTALL REAR FLEXIBLE HOSE


    1. A017C06

      Install the rear flexible hose to the rear shock absorber with coil spring with the bolt.

      Torque:
      19 N*m  { 194 kgf*cm, 14 ft.*lbf }

      Note

      Do not twist the rear flexible hose when installing it.

  10. STABILIZE SUSPENSION


    1. A017FEHE01

      Jack up the rear axle carrier, placing a wooden block underneath to avoid damage. Apply load to the suspension so that the installed bolt of the rear No. 1 suspension arm (inner side) is horizontally aligned with the center of the rear axle hub.

      CAUTION:

      Do not jack up the rear axle carrier subassembly too high as the vehicle may fall.

      Note

      Do not bend the brake dust cover.

      Tech Tips


      • If the rear drive shaft assembly cannot be positioned horizontally as shown in the illustration even when the rear axle carrier subassembly is jacked up, apply additional load to the vehicle such as by having a person sit in the rear seat.

      • Use the same procedures for the RH side and LH side.

  11. FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY


    1. A017FNT

      Fully tighten the bolt.

      Torque:
      112 N*m  { 1141 kgf*cm, 82 ft.*lbf }

      Note


      • Since a stopper nut is used, fully tighten the bolt.

      • The final torque must be applied under standard vehicle height conditions.

  12. FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY


    1. A017DR1

      Fully tighten the bolt.

      Torque:
      112 N*m  { 1141 kgf*cm, 82 ft.*lbf }

      Note


      • Since a stopper nut is used, fully tighten the bolt.

      • The final torque must be applied under standard vehicle height conditions.

  13. FULLY TIGHTEN REAR STRUT ROD ASSEMBLY


    1. A017CNE

      Fully tighten the 2 bolts.

      Torque:
      80 N*m  { 815 kgf*cm, 59 ft.*lbf }

      Note


      • Since stopper nuts are used, fully tighten the bolts.

      • The final torque must be applied under standard vehicle height conditions.

  14. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY


    1. A017DVV

      Install the No. 3 parking brake cable assembly with the bolt and the nut.

      Torque:
      Bolt
      39 N*m  { 397 kgf*cm, 29 ft.*lbf }
      Nut
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

      Note

      Do not twist the No. 3 parking brake cable assembly when installing it.

  15. INSTALL REAR WHEEL

    Torque:
    103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

  16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  17. INSPECT AND ADJUST REAR WHEEL ALIGNMENT

    Tech Tips

    Click here

  18. CHECK FOR SPEED SENSOR SIGNAL

    Tech Tips

    Click here