Click here

OIL PUMP INSTALLATION

Click here
Click here
  1. Click here

    INSTALL TIMING CHAIN CASE OIL SEAL


    1. A017DW1E04

      Using SST, tap in a new oil seal until its surface is flush with the timing chain case edge.

      09223-22010
      09506-35010
      Note:

      • Keep the lip free from foreign matter.

      • Do not tap on the oil seal at an angle.

      • Make sure that the oil seal edge does not stick out of the timing chain case.

  2. Click here

    INSTALL TIMING CHAIN COVER SUB-ASSEMBLY


    1. A017G4RE04

      Apply seal packing in a continuous line to the engine unit as shown in the following illustration.

      Seal packing
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
      Seal diameter
      3.0 mm (0.118 in.)
      Note:

      • Be sure to clean and degrease the contact surfaces, especially the surfaces indicated by C in the illustration.

      • If the contact surfaces are wet, wipe them with an oil-free cloth before applying seal packing.

      • Install the chain cover sub-assembly within 3 minutes after applying seal packing.

      • Do not start the engine for at least 2 hours after installing the chain cover sub-assembly.

    2. A017D22E01

      Apply seal packing in a continuous line to the timing chain cover as shown in the following illustration.

      Seal packing
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
      Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent
      Note:

      • If the contact surfaces are wet, wipe them with an oil-free cloth before applying seal packing.

      • Install the chain cover sub-assembly within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.

      • Do not start the engine for at least 2 hours after installing the chain cover sub assembly.

      Apply seal packing as follows
      Area Seal Packing Diameter Application Position from Inside Seal Line
      Continuous Line Area 4.5 mm (0.177 in.) or more 3.0 to 4.0 mm (0.118 to 0.158 in.)
      Alternate Long and Short Dashed Line Area 3.5 mm (0.138 in.) or more 2.0 to 3.0 mm (0.079 to 0.118 in.)
      Dashed Line Area 3.5 mm (0.138 in.) or more 3.0 to 4.0 mm (0.118 to 0.158 in.)
      Diagonal Line Area 6.0 mm (0.236 in.) or more 5.0 mm (0.197 in.)
    3. A017F8XE01

      Install a new gasket.

    4. A017F2AE01

      Align the oil pump's drive rotor spline and the crankshaft as shown in the illustration. Install the spline and chain cover to the crankshaft.

    5. A017BG1E04

      Temporarily tighten the timing chain cover with the 23 bolts and 2 nuts.

      Table 1. Bolt length
      Item Length
      Bolt A 40 mm (1.57 in.)
      Bolt B 55 mm (2.17 in.)
      Bolt C 25 mm (0.98 in.)
      Note:

      Make sure that there is no oil on the bolt threads.

    6. Fully tighten the bolts in area 1 and area 2.

      21 N*m 214 kgf*cm 15 ft.*lbf

    7. Fully tighten the bolts and nuts in area 3.

      21 N*m 214 kgf*cm 15 ft.*lbf
      Tip:

      Tighten the bolts and nuts from top to bottom as shown in the illustration.

    8. Fully tighten the bolts in area 4.

      Bolt A
      43 N*m 438 kgf*cm 32 ft.*lbf
      Except bolt A
      21 N*m 214 kgf*cm 15 ft.*lbf
      Tip:

      Tighten the bolts from bottom to top as shown in the illustration.

  3. Click here

    INSTALL OIL PAN SUB-ASSEMBLY


    1. A017EK0E02

      Using an E8 "TORX" socket wrench, install the 4 stud bolts.

      Table 2. Text in Illustration
      *a Lower Cylinder Block *b Timing Chain Cover
      *c Oil Pan Sub-assembly LH Side - -
      Bolt A
      10 N*m 102 kgf*cm 7 ft.*lbf
      Bolt B
      9.0 N*m 92 kgf*cm 80 in.*lbf
    2. A017D6L

      Install 2 new O-rings.

    3. A017EG7E05

      Apply seal packing in a continuous line as shown in the illustration.

      Seal Packing
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
      Seal Diameter
      3.0 to 4.0 mm (0.118 to 0.157 in.)
      Note:

      • Remove any oil from the contact surface.

      • Install the oil pan sub-assembly within 3 minutes of applying seal packing.

      • Do not start the engine for at least 2 hours after installation.

    4. A017FQ1E02

      Install the oil pan sub-assembly with the 16 bolts and 2 nuts.

      Bolt A
      10 N*m 102 kgf*cm 7 ft.*lbf
      Except Bolt A
      21 N*m 214 kgf*cm 15 ft.*lbf
  4. Click here

    INSTALL OIL STRAINER SUB-ASSEMBLY


    1. A017BUKE11

      Using an E6 "TORX" socket wrench, install the stud bolts as shown in the illustration.

      4.0 N*m 41 kgf*cm 35 in.*lbf
    2. A017DJHE01

      Install a new gasket and the oil strainer sub-assembly with the bolt and 2 nuts.

      10 N*m 102 kgf*cm 7 ft.*lbf
  5. Click here

    INSTALL NO. 2 OIL PAN SUB-ASSEMBLY


    1. A017EWDE01

      Using an E6 "TORX" socket wrench, install the stud bolts as shown in the illustration.

      4.0 N*m 41 kgf*cm 35 in.*lbf
    2. A017C1JE04

      Apply seal packing in a continuous line as shown in the illustration.

      Seal Packing
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
      Seal Diameter
      3.0 to 4.0 mm (0.118 to 0.157 in.)
      Note:

      • Remove any oil from the contact surface.

      • Install the No. 2 oil pan sub-assembly within 3 minutes of applying seal packing.

      • Do not start the engine for at least 2 hours after installation.

    3. A017B87E01

      Install the No. 2 oil pan sub-assembly with the 16 bolts and 2 nuts.

      10 N*m 102 kgf*cm 7 ft.*lbf
  6. Click here

    INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 2)


    1. A017EYBE01

      Apply seal packing as shown in the illustration.

      Seal Packing
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
      Note:

      • Remove any oil from the contact surfaces.

      • Install the cylinder head cover sub-assembly within 3 minutes of applying seal packing.

      • Do not start the engine for at least 2 hours after installation.

    2. A017FVT

      Install 3 new gaskets as shown in the illustration.

    3. Install a new cylinder head cover gasket to the cylinder head cover sub-assembly.

    4. A017BDFE03

      Install the cylinder head cover sub-assembly with the 12 bolts and a new seal washer.

      Bolt A
      21 N*m 214 kgf*cm 15 ft.*lbf
      Except bolt A
      10 N*m 102 kgf*cm 7 ft.*lbf
      Tip:

      After tightening all bolts, check the tightening torque of 1 and 10. Retighten the bolt if necessary.

  7. Click here

    INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 1)


    1. A017G6LE01

      Apply seal packing as shown in the illustration.

      Seal Packing
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
      Note:

      • Remove any oil from the contact surface.

      • Install the cylinder head cover sub-assembly within 3 minutes of applying seal packing.

      • Do not start the engine for at least 2 hours after installation.

    2. A017F2Q

      Install 3 new gaskets as shown in the illustration.

    3. Install a new cylinder head cover gasket to the cylinder head cover sub-assembly.

    4. A017CFIE01

      Install a cylinder head cover sub-assembly with the 12 bolts and a new seal washer.

      Bolt A
      21 N*m 214 kgf*cm 15 ft.*lbf
      Except bolt A
      10 N*m 102 kgf*cm 7 ft.*lbf
      Tip:

      After tightening all bolts, check the tightening torque of 1 and 11. Retighten the bolt if necessary.

  8. Click here

    INSTALL WATER INLET HOUSING


    1. A017DWR

      Install a new water inlet housing No. 1 gasket and water outlet pipe O-ring.

    2. A017EHTE04

      Install the water inlet housing with the 2 bolts and nut.

      10 N*m 102 kgf*cm 7 ft.*lbf
      Note:

      Be careful not to allow the O-ring to get caught between the parts.

    3. Connect the water hose.

  9. Click here

    INSTALL OIL COOLER PIPE


    1. A017B70

      Install a new gasket to the oil pan sub-assembly.

    2. Install the oil cooler pipe with the bolt and 2 nuts.

      21 N*m 214 kgf*cm 15 ft.*lbf
  10. Click here

    INSTALL CRANKSHAFT PULLEY


    1. Align the pulley set key with the key groove of the crankshaft pulley, and slide on the crankshaft pulley.

    2. A017GAJE01

      Using SST, install the pulley bolt.

      09213-70011 09213-70020
      09330-00021
      250 N*m 2550 kgf*cm 184 ft.*lbf
  11. Click here

    INSTALL OIL PIPE


    1. Make sure that there is no foreign matter on the mesh of the oil control valve filter RH.

      Note:

      Do not touch the mesh when installing the oil control valve filter RH.

    2. A017DWSE11

      Install the oil control valve filter RH to the oil pipe union. Install new gaskets and temporarily install the oil pipe (on the cylinder head cover sub-assembly side).

    3. Install a new gasket and temporarily install the oil pipe (on the cylinder head sub-assembly side) with the oil pipe union.

    4. Install the bolt (A) to the cylinder head sub-assembly.

      10 N*m 102 kgf*cm 7 ft.*lbf

    5. Tighten the oil pipe union (on the cylinder head cover sub-assembly side).

      65 N*m 663 kgf*cm 48 ft.*lbf

    6. Tighten the oil pipe union (on the cylinder head sub-assembly side).

      65 N*m 663 kgf*cm 48 ft.*lbf
      Note:

      If the link that connects the gaskets is broken, remove the connecting link by using side cutters or a similar tool.

  12. Click here

    INSTALL NO. 1 OIL PIPE


    1. Make sure that there is no foreign matter on the mesh of the oil control valve filter LH.

      Note:

      Do not touch the mesh when installing the oil control valve filter LH.

    2. A017BIAE01

      Install the oil control valve filter LH to the oil pipe union. Install new gaskets and temporarily install the No. 1 oil pipe (on the cylinder head cover sub-assembly side).

    3. Install a new gasket and temporarily install the No. 1 oil pipe (on the cylinder head sub-assembly side) with the oil pipe union.

    4. Tighten the oil pipe union (on the cylinder head cover sub-assembly side).

      65 N*m 663 kgf*cm 48 ft.*lbf

    5. Tighten the oil pipe union (on the cylinder head sub-assembly side).

      65 N*m 663 kgf*cm 48 ft.*lbf
      Note:

      If the link that connects the gaskets is broken, remove the connecting link by using side cutters or a similar tool.

  13. Click here

    INSTALL ENGINE HANGERS


    1. A017DNOE01

      Install the 2 engine hangers with the 4 bolts as shown in the illustration.

      Part No.
      No. 1 Engine hanger 12281-31120
      No. 2 Engine hanger 12282-31100
      Bolts 91671-10825
      33 N*m 337 kgf*cm 24 ft.*lbf

    2. Attach the engine sling device and hang the engine with the chain block.

  14. Click here

    REMOVE ENGINE STAND

  15. Click here

    INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

    Tip:

    Click here.